diagram YAMAHA YZF-R1SC 2004 User Guide

2-32
1Oil cooler
2Oil filter cartridge
3Oil level switch
4Oil strainer
5Oil pump
6Oil pipe
LUBRICATION DIAGRAMSSPEC
ProCarManuals.com

2-33
1Main axle
2Oil delivery pipe
3Drive axle
LUBRICATION DIAGRAMSSPEC
ProCarManuals.com

2-34
1Cylinder head
2Crankshaft
LUBRICATION DIAGRAMSSPEC
ProCarManuals.com

2-44
K Pass the water hose lower side
of the thermostat, and between
the ground lead and the neutral
switch.
L Install the leads so that the en-
gine ground lead is positioned
lower and the battery negative
lead to be upper. Install the pro-
trusion of each lead to be above
the vehicle.
M Route the crankshaft position
sensor lead under the wire har-
ness.
N To the fuel pump
O Clamp the wire harness winding
in and insert it to the frame hole.A Pass the wire harness through
the clamp inserted to the radiator
stay.
B To the headlight lead
C Clamp the lead between three
protrusions of the pipe (the first
and second parts from the ve-
hicle front). Point the tip of the
clamp (excessive part) to the in-
side of the vehicle.
D To the vehicle right side diagram
E To the engine
F Clamp the lead between three
protrusions of the pipe (the in-
side and outside of the vehicle).G Point the tip of the clamp (exces-
sive part) to the inside of the ve-
hicle.
H All hoses and leads should be
routed over the vehicle’s upper
side above the heat protector.
I To the starter motor
J Fasten the wire harness, clank
shaft position sensor lead, rear
brake light switch lead and
speed sensor lead with a clamp.
Then, point the tip of the clamp
(cut the tip of the clamp leaving 2
to 4 mm (0.08 to 0.16 in).) to the
inside of the vehicle.
CABLE ROUTINGSPEC
ProCarManuals.com

7-2
FUEL INJECTION SYSTEMFI
7
WIRING DIAGRAM
ProCarManuals.com

7-47
AIR INDUCTION SYSTEMFI
A To cylinder #1 and #2
B To cylinder #3 and #41 Air cut-off valve
2 Plate
3 Reed valve assembly
4 Reed valve cap
5 To air filter case
EAS00509
AIR INDUCTION SYSTEM DIAGRAMS
ProCarManuals.com

8-8
IGNITION SYSTEMELEC
EAS00735
IGNITION SYSTEM
CIRCUIT DIAGRAM
ProCarManuals.com

8-13
IGNITION SYSTEMELEC
12. Starting circuit cut-off relay (diode)

Disconnect the starting circuit cut-off relay
coupler from the wire harness.

Connect the pocket tester (Ω
1) to the
starting circuit cut-off relay coupler as
shown.

Check the starting circuit cut-off relay for
continuity.
Positive tester probe

blue / yellow
Negative tester probe

sky blue
1
2
EAS00753
Positive tester probe

blue / yellow
Negative tester probe

blue / black Continuity
1
3
Positive tester probe

sky blue
Negative tester probe

blue / yellow
2
1
Positive tester probe

blue / black
Negative tester probe

blue / yellow No
continuity
3
1
YESNO
Replace the starting
circuit cut-off relay. When you switch the positive and negative
tester probes, the readings in the above chart
will be reversed.

Are the tester readings correct?
NOTE:
13. Lean angle cut-off switch

Check the lean angle cut-off switch.
Refer to “FUEL INJECTION SYSTEM” in
chapter 7.

Is the lean angle cut-off switch OK?
YESNO
Replace the lean
angle cut-off switch.
EAS00754
14. Wiring

Check the entire ignition system’s wiring.
Refer to “CIRCUIT DIAGRAM”.

Is the ignition system’s wiring properly con-
nected and without defects?
YESNO
Properly connect or
repair the ignition
system’s wiring.
Replace the ECU.
ProCarManuals.com

8-14
1Main switch
4Fuse (main)
6Battery
8Starter relay
9Starter motor
10Starting circuit cut-off relay
11Neutral switch
12Sidestand switch
53Engine stop switch
54Start switch
73Fuse (ignition)
ELECTRIC STARTING SYSTEMELEC
EAS00755
ELECTRIC STARTING SYSTEM
CIRCUIT DIAGRAM
ProCarManuals.com

8-18

Check the entire starting system’s wiring.
Refer to “CIRCUIT DIAGRAM”.

Is the starting system’s wiring properly con-
nected and without defects?
EAS00766
12. Wiring
YESNO
Properly connect or
repair the starting
system’s wiring.
The starting system
circuit is OK.
11. Start switch

Check the start switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the start switch OK?
YESNO
Replace the right
handlebar switch.
EAS00764
10. Clutch switch

Check the clutch switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the clutch switch OK?
YESNO
Replace the clutch
switch.
EAS00763EAS00752
9. Sidestand switch

Check the sidestand switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the sidestand switch OK?
YESNO
Replace the side-
stand switch.
ELECTRIC STARTING SYSTEMELEC
ProCarManuals.com