coolant reservoir YAMAHA YZF-R1SC 2004 Service Manual

2-3
ENGINE SPECIFICATIONSSPEC
ItemStandardLimit
Oil filter
Oil filter type
Bypass valve opening pressure
Paper
80  120 kPa (0.8  1.2 kg / cm2,
0.8  1.2 bar, 11.6  17.4 psi)








Oil pump
Oil pump type
Inner-rotor-to-outer-rotor-tip
clearance
Outer-rotor-to-oil-pump-housing
clearance
Trochoid
0.01  0.10 mm
(0.0004  0.0039 in)
0.09  0.15 mm
(0.00035  0.0059 in)



0.18 mm
(0.0071 in)
0.22 mm
(0.0087 in)
Cooling system
Radiator capacity
Radiator cap opening pressure
Radiator core
Width
Height
Depth
Coolant reservoir
Capacity
Water pump
Water pump type
Reduction ratio
Max. impeller shaft tilt
2.51 L (2.21 Imp qt, 2.65 US qt)
108  137 kPa (1.08  1.37 kg / cm2,
1.0  1.3 bar, 15.6  19.9 psi)
380 mm (14.96 in)
258 mm (10.2 in)
24 mm (0.94 in)
0.25 L (0.22 Imp qt, 0.26 US qt)
Single suction centrifugal pump
65 / 43
25 / 32 (1.181)































0.15 mm
(0.006 in)
Starting system typeElectric starter
Spark plugs
Model (manufacturer)
quantity
Spark plug gap
CR9EK (NGK)
4
0.6  0.7 mm (0.0236  0.0276 in)







Cylinder head
Volume
Max. warpage
12.5  13.1 cm3 (0.76  0.80 cu.in)







0.10 mm
(0.0039 in)
ProCarManuals.com

2-23
TIGHTENING TORQUESSPEC
See NOTE 2 CHASSIS TIGHTENING TORQUES
ItemThreadTighteningRemarksItemsizeNmm
kgft
lbRemarks
Upper bracket and outer tubeM8262.619
Upper bracket and steering stem nutM2811 311.382
Handlebar and outer tubeM8171.712
Handlebar and upper bracketM6131.39
Steering shaft and ring nutM30181.813See NOTE 1
Outer tube and under bracketM8232.317
Main switch and upper bracketM8262.619
Front brake master cylinder cap stopperM41.20.120.9
Front brake hose union boltsM10303.022
Front brake master cylinder and bracketM6131.39
Meter assembly and front cowling stay—1.30.130.9
Headlight and front cowling stay—0.80.080.6
Front cowling and headlight assembly—1.50.151.1
Cover 7, 8 and frameM650.53.6
Under cowling and engineM650.53.6
Windshield and front cowlingM50.40.040.3
Duct and console panelM51.30.130.9
End grip and handlebarM640.42.9
Horn bracket and under bracketM640.42.9
Coolant reservoir tank and frameM650.53.6
Engine mount front (left and right)M10454.533
Engine mount rear upperM10515.137
Engine mount rear underM10515.137
Engine mount rear adjust boltM1670.75.1
Catalyst pipe stay and frameM10444.432
Clutch cable lock nut (engine side)M870.75.1
Main frame and rear frameM10414.130
Throttle cable adjust nut (throttle body side)M650.53.6
Cover 2 and plate—0.80.080.6
Pivot shaft and nutM1810510.576
Connecting rod and frameM10444.432
Relay arm and connecting rodM10444.432
Relay arm and swingarmM10444.432
Rear shock absorber and relay armM10444.432
Rear shock absorber and upper bracketM10444.432
Upper bracket and frameM14929.267
Seal guardM670.75.1
Drive chain caseM670.75.1
Chain puller adjust nutM8161.612
Fuel tank and fuel pump assemblyM540.42.9
Fuel tank stay (front side) and frameM670.75.1
Fuel tank and fuel tank stay (front side)M670.75.1
Fuel tank stay (rear side) and rear frameM670.75.1
Side cover and fuel tankM50.40.040.3
Rider seat and frameM670.75.1
Seat lock plate and rear frameM6101.07
Side cover (rear side) and frameM540.42.9
ProCarManuals.com

2-39
E Clamp the clamp upper end
along the line of lower end of the
hose clamp assembly. Point the
tip of the clamp (surplus section)
to the front side of the vehicle.
Clutch cable is what the clamp
fastens.
F The clutch cable doesn’t project
outside the water hose and the
cylinder head in the box part in
the figure.
G To the engine
H Clamp behind the bracket 3.17Throttle body lead
A Clamp it after passing between
the frame and radiator stay.
Point the tip of the clamp (exces-
sive part) to the front side of the
vehicle. Fasten the right handle-
bar switch lead with a clamp.
B To the wire harness
C The clutch cable positioning
guide should be above the upper
end of the clamp. Fasten the
clutch cable with a clamp. (Refer
to )
D Position relation between the
clamp and guide.
M
CABLE ROUTINGSPEC
1Wire harness
2Crankshaft position sensor lead
3Heat protector
4Right handlebar switch lead
5Positioning guide
6Rear brake light switch lead
7Coolant reservoir tank
8Speed sensor lead
9Clutch cable
10Radiator
11Oil cooler outlet hose
12Coolant reservoir tank drain
hose
13Breather pipe
14Fuel tank drain hose
15A.C. magneto lead
16Wire harness
ProCarManuals.com

2-40
P To the air filter
Q Route the fuel tank drain hose
over the canister stay and be-
tween the breather hose 2 and
wire harness. On the front side of
the canister stay, let though the
bottom of the A.C.magneto lead
and the wire harness.
R Route by the upside of vehicle
away from the canister stay.
CABLE ROUTINGSPEC
I The coupler for the air induction
solenoid lead and camshaft sen-
sor lead should be connected
above the ignition coil sub wire
harness and it should not drop
on the cylinder head cover be-
hind the ignition coil.
J Pass the right handlebar switch
lead between the frame and heat
protector.
K Coolant reservoir tank drain
hose should cross with the
speed sensor lead under the
swingarm bracket. Route the
coolant reservoir tank drain hose
over the up side of the vehicle.L Pass the rear brake light switch
lead between the swingarm
bracket and coolant reservoir
tank.
M Release the tip of the clamp and
install it to the clutch cable.
Insert the clamp to the hole lo-
cated on the right back side of
the radiator.
Radiator fan motor lead should
not be caught while inserting the
clamp.
N Push the clamp until it hits the ra-
diator side stay. Radiator fan mo-
tor lead should not be caught.
O Clamp the clutch cable so that it
is within this specified clamp.
ProCarManuals.com

2-41
C Fold back the clamp and secure
it after passing the lead through
the clamp.
D To the EXUP servo motor
E Pass the coolant reservoir tank
drain hose and fuel tank drain
hose through the clamp from the
outer side of the water pump inlet
pipe after routing it behind the
water pump breather hose.
The lengths of two hose ends are
allowed to be random. Any direc-
tion of cut edges can be ac-
cepted. (Only for the fuel tank
drain hose)
F Clamp the fuel tank drain hose
and fuel tank breather hose.A Clamp the leads so that they are
positioned inner of the vehicle
than the washer position after
routing them between the frame
and radiator stay. Align the clamp
position with the taping sections
of leads. Point the tip of the clamp
(surplus section) to the down
front side of the vehicle.
What the clamp fastens at this
stage are the handlebar switch
and main switch leads.
B Pass the main switch lead and
left handlebar switch lead be-
tween the frame and the heat
protector.
CABLE ROUTINGSPEC
1Heat protector
2Main switch lead
3Left handlebar switch lead
4EXUP servo motor lead
5Coolant reservoir tank drain hose
6Fuel tank drain hose
7Coolant outlet pipe
8Sidestand switch lead
9Oil level switch lead
10A.C.magneto lead
11Fuse box stay
12Water hose
13Stay 1
14Chain case cover
ProCarManuals.com

2-42
R Arrange so as not for each hose
to cross in the part between “BB”
from the section “AA” which is in
the illustration.G Route the lead by the inside of
the water hose and water pipe.
H Route the lead by the inside of
the water hose and water pipe.
I Route by the outside of vehicle
away from the water hose.
J Point the tip of the clamp (exces-
sive part) to the down rear side of
the vehicle. Fasten the wire har-
ness with a clamp.
K Route the water hose so that it is
placed at the outermost position
finally after routing other leads
and hoses in the guide.
L To the coolant reservoir tank
CABLE ROUTINGSPEC
M There should be no exposure of
bared conductors due to the dis-
placement of the tube.
N Route the coolant reservoir tank
drain hose so that it is routed at
the innermost position to each
hose and lead.
O Can be routed in any order.
P Align the molded part of the fuel
tank drain hose with the stay 1.
Q Routing of the fuel tank drain
hose.
EXUP servo motor, oil level
switch and sidestand switch
leads are omitted in this drawing.
ProCarManuals.com

2-43
33Throttle body side cap
34Mud guard
35Turn signal light lead
36License plate light lead
37Rear fender rib
38Speed sensor lead
39Rear brake light switch lead
40Rear frame
41Swingarm bracket
42Main fuse lead
43Starting circuit cut-off relay lead
44Turn signal light relay lead
45Starter relay lead
46Main fuse lead (To the battery
positive lead)
47Right handlebar switch lead
17Battery negative lead
18Starter motor lead
19A.C.magneto lead
20Oil level switch lead
21Sidestand switch lead
22Throttle body lead
23Coolant reservoir tank drain hose
24Fuel tank drain hose
25Cover 7
26Radiator fan motor lead (left)
27Radiator fan motor lead (right)
28Wire harness
29Pipe 3
30Frame
31Coolant reservoir tank hose
32Thermo stat assembly breather
hose
CABLE ROUTINGSPEC
1Heat protector
2Crankshaft position sensor lead
3Neutral switch lead
4Ground lead
5Coolant reservoir tank
6Battery positive lead
7Starter relay
8Turn signal relay
9Main fuse
10Lean angle cut-off switch
11Atmospheric pressure sensor
12Tail / brake light lead
13Rear fender
14Seat lock cable
15Anti safety alarm coupler
16Starting circuit cut-off relay
ProCarManuals.com

3-39
CHANGING THE COOLANT
CHK
ADJ
CAUTION:
EAS00105
CHANGING THE COOLANT
1. Remove:

bottom cowlings

side cowlings
Refer to “COWLINGS”.

rider seat
Refer to “SEATS”.
2. Remove:

coolant reservoir tank

coolant reservoir hose
3. Disconnect:

coolant reservoir cap
1
4. Drain:

coolant
(from the coolant reservoir tank)
5. Remove:

radiator cap
1
A hot radiator is under pressure. Therefore,
do not remove the radiator cap when the en-
gine is hot. Scalding hot fluid and steam may
be blown out, which could cause serious in-
jury. When the engine has cooled, open the
radiator cap as follows:
Place a thick rag or a towel over the radiator
cap and slowly turn the radiator cap coun-
terclockwise toward the detent to allow any
residual pressure to escape. When the his-
sing sound has stopped, press down on the
radiator cap and turn it counterclockwise to
remove.
The following procedure applies to all of the
coolant drain bolts and copper washers.
6. Remove:

coolant drain bolts
1
(along with the copper washers)
ProCarManuals.com

3-40
CHANGING THE COOLANT
CHK
ADJ
10 Nm (1.0 m
kg, 7.2 ft
lb)
WARNING
7. Drain:

coolant
(water pump inlet pipe and outlet pipe)
8. Check:

copper washers
1 New
9. Install:

coolant drain bolts
2
(with copper washers)
10. Install:

coolant reservoir tank
11. Connect:

coolant reservoir hose
12. Fill:

cooling system
(with the specified amount of the recom-
mended coolant)
Recommended antifreeze
High-quality ethylene glycol
antifreeze containing corrosion
inhibitors for aluminum engines
Mixing ratio
1:1 (antifreeze:water)
Quantity
Total amount
2.51 L
(2.21 Imp qt, 2.65 US qt)
Coolant reservoir capacity
0.25 L
(0.22 Imp qt, 0.26 US qt)
Handling notes for coolant
Coolant is potentially harmful and should be
handled with special care.

If coolant splashes in your eyes, thorough-
ly wash them with water and consult a doc-
tor.

If coolant splashes on your clothes, quick-
ly wash it away with water and then with
soap and water.

If coolant is swallowed, induce vomiting
and get immediate medical attention.
ProCarManuals.com

3-41
CHANGING THE COOLANT
CHK
ADJ
CAUTION:
NOTE:
Adding water instead of coolant lowers the
antifreeze content of the coolant. If water is
used instead of coolant check, and if nec-
essary, correct the antifreeze concentra-
tion of the coolant.

Use only distilled water. However, if dis-
tilled water is not available, soft water may
be used.

If coolant comes into contact with painted
surfaces, immediately wash them with wa-
ter.

Do not mix different types of antifreeze.
13. Install:

radiator cap
14. Fill:

coolant reservoir tank
(with the recommended coolant to the maxi-
mum level mark
a)
15. Install:

coolant reservoir cap
16. Start the engine, warm it up for several min-
utes, and then stop it.
17. Check:

coolant level
Refer to “CHECKING THE COOLANT LEV-
EL”.
Before checking the coolant level, wait a few
minutes until the coolant has settled.
18. Install:

rider seat
Refer to “SEATS”.

bottom cowlings

side cowlings
Refer to “COWLINGS”.
ProCarManuals.com