ignition YAMAHA YZF-R1SC 2004 User Guide

3-68
CHECKING THE FUSES
CHK
ADJ
WARNING
Pocket tester
90890-03112, YU-3112
b. If the pocket tester indicates “∞”, replace the
fuse.
3. Replace:

blown fuse
a. Set the main switch to “OFF”.
b. Install a new fuse of the correct amperage
rating.
c. Set on the switches to verify if the electrical
circuit is operational.
d. If the fuse immediately blows again, check
the electrical circuit.
Fuses
Amperage
ratingQ’ty
Main50 A1
Fuel injection
system15 A1
Headlight25 A1
Signaling
system10 A1
Ignition15 A1
Backup fuse
(odometer
and clock)
10 A1
Radiator
fan motor15 A2
Reserve25 A, 15 A,
10 A1
Never use a fuse with an amperage rating
other than that specified. Improvising or us-
ing a fuse with the wrong amperage rating
may cause extensive damage to the electri-
cal system, cause the lighting and ignition
systems to malfunction and could possibly
cause a fire.
4. Install:

front cowling inner panel (left)
Refer to “COWLINGS”.

rider seat
Refer to “SEATS”.
ProCarManuals.com

5-11
Order Job / Part Q’ty Remarks
1
2
3
4Removing the cylinder head cover
Fuel tank
Side and bottom cowlings
Throttle body assembly
Radiator assembly
Air cut-off valve
Ignition coil
Spark plug
Cylinder head cover
Cylinder head cover gasket4
4
1
1Remove the parts in the order listed.
Refer to “FUEL TANK” in chapter 3.
Refer to “COWLINGS” in chapter 3.
Refer to “THROTTLE BODIES” in
chapter 7.
Refer to “RADIATOR” in chapter 3.
Refer to “AIR INDUCTION SYSTEM” in
chapter 7.
13 Nm (1.3 m
kg, 9.4 ft
lb)
8 Nm (0.8 m
kg, 5.7 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
CAMSHAFTENG
EAS00194
CAMSHAFT
CYLINDER HEAD COVER
ProCarManuals.com

7-1
FUEL INJECTION SYSTEMFI
19Atmospheric pressure
sensor
20Fuel injection system
relay
21Engine trouble warning
light
22Lean angle cut-off
switch
23Air cut-off valve
13Coolant temperature
sensor
14Spark plug
15Cylinder identification
sensor
16Pressure regulator
17Battery
18ECU
1Ignition coil
2Air filter case
3Intake temperature
sensor
4Fuel delivery hose
5Fuel tank
6Fuel pump
7Fuel return hose
8Intake air presure sen-
sor
9Throttle position sen-
sor
10Fuel injector
11Catalytic converter
12Crankshaft position
sensor
FUEL INJECTION SYSTEM
FUEL INJECTION SYSTEM
ProCarManuals.com

7-3
FUEL INJECTION SYSTEMFI
1Main switch
4Fuse (main)
5Fuse (backup)
6Battery
7Fuse (fuel injection)
10Starting circuit cut-off relay
11Neutral switch
12Sidestand switch
13Fuel pump
14E.C.U.
15Ignition coil #1
16Ignition coil #2
17Ignition coil #3
18Ignition coil #4
19Spark plug
20Injector #1
21Injector #2
22Injector #3
23Injector #4
25Sub-throttle position sensor
26EXUP servo motor
27Speed sensor
28Coolant temperature sensor
29Intake air temperature sensor
31Crankshaft position sensor
32Throttle position sensor
33Intake air pressure sensor
34Atmospheric pressure sensor
35Cylinder identification sensor
36Lean angle cut-off switch
43Multi function meter
53Engine stop switch
73Fuse (ignition)
ProCarManuals.com

7-5
FUEL INJECTION SYSTEMFI
SUBSTITUTE CHARACTERISTICS OPERATION CONTROL (FAIL-SAFE ACTION)
If the ECU detects an abnormal signal from a sensor while the vehicle is being driven, the ECU illumi-
nates the engine trouble warning light and provides the engine with alternate operating instructions
that are appropriate for the type of malfunction.
When an abnormal signal is received from a sensor, the ECU processes the specified values that are
programmed for each sensor in order to provide the engine with alternate operating instructions that
enable the engine to continue to operate or stop operating, depending on the conditions.
The ECU takes fail-safe actions in two ways: one in which the sensor output is set to a prescribed value,
and the other in which the ECU directly operates an actuator. Details on the fail-safe actions are given
in the table below.
FAIL-SAFE ACTIONS TABLE
Fault
Code No.ItemSymptomFail-safe actionAble / unable
to startAble / unable
to drive
11
Cylinder identification
sensorNo normal signals are received from
the cylinder identification sensor.Continues to operate the engine based
on the results of the cylinder
identification that existed up to that
point.
UnableAble
12Crankshaft position
sensorNo normal signals are received from
the crankshaft position sensor.
Stops the engine (by stopping the
injection and ignition).UnableUnable
13
14Intake air pressure
sensor (open or short
circuit) (pipe system)Intake air pressure sensor-open or
short circuit detected.
Faulty intake air pressure sensor
system.
Fixes the intake air pressure to
101.3 kpa.
AbleAble
15
16Throttle position sensor
(open or short circuit)
(stuck)Throttle position sensor-open or short
circuit detected.
Fixes the throttle position sensor to
fully open.AbleAble
17EXUP servo motor
potention
(open or short circuit)EXUP servo motor potention-open or
short circuit detected.
Turn the EXUP servo motor toward
the open side for 3 seconds and then
stop it.AbleAble
18
EXUP servo motor (lock)A lock of the EXUP servo motor is
detected.
Perform the preventive control
against motor locking.
Perform the lock release operation
twice every 100 seconds.
AbleAble
19Sidestand switch (open
circuit in wire to ECU)Open circuit in the input line of ECU
No.15 terminal is detected when the
start switch is pressed.-- (No start)UnableUnable
20Intake air pressure
Atmospheric pressureDefective values are detected due to
the internal malfunction
Fixes the intake air pressure and
atmospheric pressure to 101.3 kpa.AbleAble
21Coolant temperature
sensorCoolant temperature sensor-open or
short circuit detected.
Fixes the coolant temperature to
60C.AbleAble
22Intake temperature
sensorIntake temperature sensor-open or
short circuit detected.
Fixes the intake temperature to 20C.AbleAble
23Atmospheric pressure
sensorAtmospheric pressure sensor-open or
short circuit detected.
Fixes the atmospheric pressure to
101.3 kpa.AbleAble
33
34
35
36
Faulty ignitionOpen circuit detected in the primary
lead of the ignition coil.
Cut the injection of other cylinder in
the same group with the cylinder that
the error is detected.
(Example: when the #1 cylinder is
detective, cut the injection of #1 and
#4 cylinders, when the #2 cylinder is
detective, cut the injection of #2 and
#3 cylinders).
Turn on the power to the air induction
solenoid to always cut-off the air.
Able
(depending
on the num-
ber of faulty
cylinders)Able
(depending
on the num-
ber of faulty
cylinders)
30
41Lean angle cut-off
switch (latch up
detected) (open or short
circuit)Lean angle cut-off switch-open or short
circuit detected.
Turns OFF the fuel injection system
relay of the fuel system.
UnableUnable
42Speed sensor, neutral
switchNo normal signals are received from the
speed sensor; or, an open or short
circuit is detected in the neutral switch.
Fixes the gear to the top gear.AbleAble
43Fuel system voltage
(monitor voltage)The ECU is unable to monitor the
battery voltage (an open circuit in the
line to the ECU).
Fixes the battery voltage to 12 V.AbleAble
44
Error in writing the
amount of CO
adjustment on
EEPROMAn error is detected while reading or
writing on EEPROM (CO adjustment
value).--
AbleAble
ProCarManuals.com

7-7
Engine operation is not normal or the engine trouble warning light is on.
* Engine trouble warning light may not come on even if the engine operation is not normal.
The engine trouble warning light comes on.
Check the fault code number displayed on the me-
ter.
Identify the probable cause of malfunction. (Refer
to the “Diagnostic fault code table”.)
Check and repair the probable case of malfunc-
tion.
Fault code No.
appearFault code No.
disappear
Check and repair.
(Refer to “TROU-
BLESHOOTING DE-
TAILS”.)
Monitor the operation
of the sensors and
actuators in the diag-
nostic mode. (Refer
to “Diagnostic mode
table” in chapter 7)Check and repair.
(Refer to “FAIL-SAFE
ACTIONS TABLE”.)
Perform ECU reinstatement action. (Refer to “Re-
instatement method” in “TROUBLESHOOTING
DETAILS”.)
Turn the main switch to “OFF”, turn the main switch
back to “ON”, and then check if the fault code num-
ber is still displayed.
Erasing the malfunction history:*
The malfunction history is stored even if the main
switch is turned OFF.
The malfunction history must be erased in the
diagnostic mode. (Refer to the “Diagnostic mode
table (Diagnostic code No.62)”)Repairs completed
The engine trouble warning light does not come
on.
Check the operation of following sensors and ac-
tuators in the diagnostic mode (Refer to “Diagnos-
tic mode table” in chapter 7.)
Malfunction of en-
gineDefective sensor
or actuator
Check and repair
the inner parts of
engine. (Refer to
Chapter 5)Check and repair
the corresponding
sensor or actua-
tor.
* Operated when the engine trouble warning light is on.
Fault code
number displayed
Fault code number not displayed
OKNG
OK
OK
Check the engine condition.
OK NG
01: Throttle position
sensor (throttle
angle)
03: Intake air pressure
07: Vehicle speed pulse
09: Fuel system volt-
age (battery bolt)
21: Neutral switch
30: Ignition coil #1
31: Ignition coil #232: Ignition coil #3
33: Ignition coil #4
36: Injector #1
37: Injector #2
38: Injector #3
39: Injector #4
48: Al system solenoid
53: EXUP servo motor
56: Sub-throttle servo
motor
FUEL INJECTION SYSTEMFI
EAS00904
TROUBLESHOOTING CHART
ProCarManuals.com

7-10
FUEL INJECTION SYSTEMFI
Diagnostic fault code table
Fault
code No.SymptomProbable cause of malfunctionDiagnostic
code
11
No normal signals are received from
the cylinder identification sensor.
Open or short circuit in wiring sub lead.

Open or short circuit in wiring harness.

Defective cylinder identification sensor.

Malfunction in ECU.

Improperly installed sensor.
—
12
No normal signals are received from
the crankshaft position sensor.
Open or short circuit in wiring harness.

Defective crankshaft position sensor.

Malfunction in pickup rotor.

Malfunction in ECU.

Improperly installed sensor.
—
13
Intake air pressure sensor-open or
short circuit detected.
Open or short circuit in wiring sub lead.

Open or short circuit in wiring harness.

Defective intake air pressure sensor.

Malfunction in ECU.
03
14
Faulty intake air pressure sensor hose
system; a hose is detached, causing
constant application of the
atmospheric pressure to the sensor;
or, the hose is clogged.
Intake air pressure sensor hose is detached, clogged,
kinked, or pinched.

Malfunction in ECU.
03
15
Throttle position sensor-open or
short circuit detected.
Open or short circuit in wiring sub lead.

Open or short circuit in wiring harness.

Defective throttle position sensor.

Malfunction in ECU.

Improperly installed throttle position sensor.
01
16A stuck throttle position sensor is
detected.
Stuck throttle position sensor.

Malfunction in ECU.01
17EXUP servo motor potention
circuit-open or short circuit detected.
Open or short circuit in wiring sub lead.

Detective EXUP servo motor (potention circuit).53
18EXUP servo motor is stuck.
Open or short circuit in wiring sub lead.

Stuck EXUP servo motor (mechanism).

Stuck EXUP servo motor (motor).53
19Open circuit in the input line of ECU
No.15 terminal is detected when the
start switch is pressed.
Open circuit in wiring harness (ECU Coupler).

Malfunction in ECU.20
20
When the main switch is turned to ON,
the atmospheric sensor voltage and
intake air pressure sensor voltage
differ greatly.
Atmospheric pressure sensor hose is clogged.

Intake air pressure sensor hose is clogged, kinked, or pinched.

Malfunction of the atmospheric pressure sensor in the
intermediate electrical potential.

Malfunction of the intake air pressure sensor in the
intermediate electrical potential.

Malfunction in ECU.
03
02
21Coolant temperature sensor-open or
short circuit detected.
Open or short circuit in wiring harness.

Defective coolant temperature sensor.

Malfunction in ECU.06
22Intake temperature sensor-open or
short circuit detected.
Open or short circuit in wiring harness.

Defective intake temperature sensor.

Malfunction in ECU.05
23Atmospheric pressure sensor-open or
short circuit detected.
Open or short circuit in wiring sub lead.

Defective atmospheric pressure sensor.

Malfunction in ECU.02
30The motorcycle has overturned.
Overturned.

Malfunction in ECU.08
33
Open circuit is detected in the primary
lead of the ignition coil (#1).
Open or short circuit in wiring harness.

Malfunction in ignition coil.

Malfunction in ECU.

Malfunction in a component of ignition cut-off circuit system.
30
ProCarManuals.com

7-11
FUEL INJECTION SYSTEMFI
Fault
code No.SymptomProbable cause of malfunctionDiagnostic
code
34
Open circuit is detected in the primary
lead of the ignition coil (#2).
Open or short circuit in wiring harness.

Malfunction in ignition coil.

Malfunction in ECU.

Malfunction in a component of ignition cut-off circuit system.
31
35
Open circuit is detected in the primary
lead of the ignition coil (#3).
Open or short circuit in wiring harness.

Malfunction in ignition coil.

Malfunction in ECU.

Malfunction in a component of ignition cut-off circuit system.
32
36
Open circuit is detected in the primary
lead of the ignition coil (#4).
Open or short circuit in wiring harness.

Malfunction in ignition coil.

Malfunction in ECU.

Malfunction in a component of ignition cut-off circuit system.
33
41Lean angle cut-off switch-open or
short circuit detected.
Open or short circuit in wiring harness.

Defective lean angle cut-off switch.

Malfunction in ECU.08
42
No normal signals are received from
the speed sensor; or, an open or
short circuit is detected in the neutral
switch.
Open or short circuit in wiring harness.

Defective speed sensor.

Malfunction in vehicle speed sensor detected unit.

Defective neutral switch.

Malfunction in the engine side of the neutral switch.

Malfunction in ECU.
07
21
43The ECU is unable to monitor the
battery voltage (an open circuit in the
monitor line to the ECU).
Open circuit in wiring harness.

Malfunction in ECU.09
44An error is detected while reading or
writing on EEPROM.
Malfunction in ECU. (The CO adjustment value is not
properly written on or read from the internal memory).60
46Power supply to the FI system is not
normal.
Malfunction in “CHARGING SYSTEM”.—
47Sub-throttle servo motor potention cir-
cuit-open or short circuit detected.
Open or short circuit in wiring harness.

Detective Sub-throttle servo motor (potention circuit).56
48Sub-throttle servo motor is stuck.
Open or short circuit in wiring harness.

Stuck Sub-throttle servo motor (mechanism).

Stuck Sub-throttle servo motor (motor).56
50
Faulty ECU memory. When this
malfunction is detected, the code
number might not appear on the
meter.
Malfunction in ECU. (The program and data are not
properly written on or read from the internal memory.)
—
Er-1
No signal are received from the ECU.
Open or short circuit in wiring harness.

Malfunction in meter.

Malfunction in ECU.

Defective wire connection of the ECU coupler.
—
Er-2No signal are received from the ECU
within the specified duration.
Improper connection in wiring harness.

Malfunction in meter.

Malfunction in ECU.—
Er-3Data from the ECU can not be
received correctly.
Improper connection in wiring harness.

Malfunction in meter.

Malfunction in ECU.—
Er-4Non-registered data has been
received from the meter.
Improper connection in wiring harness.

Malfunction in meter.

Malfunction in ECU.—
ProCarManuals.com

7-12
FUEL INJECTION SYSTEMFI
NOTE: Diagnostic mode table
Switch the meter display from the regular mode to the diagnosis mode. To switch the display, refer to
“DIAGNOSTIC MODE”.

Check the intake air temperature and coolant temperature as close as possible to the intake air tem-
perature sensor and the coolant temperature sensor respectively.

If it is not possible to check it with an atmospheric pressure gauge, judge it by using 101.3 kPa as the
standard.

If it is not possible to check the intake air temperature, use the ambient temperature as reference.
Diagnostic
codeItemDescription of actionData displayed on meter
(reference value)
01
Throttle angleDisplays the throttle angle.

Check with throttle fully closed.

Check with throttle fully open.0
125 degrees

Fully closed position (15
18)

Fully open position (95
100)
02
Atmospheric
pressureDisplays the atmospheric pressure.
* Use an atmospheric pressure gauge to check the
atmospheric pressure.Compare it to the value
displayed on the meter.
03
Intake air pressureDisplays the intake air pressure.
Engine stop switch is on.
* Generate the pressure difference by cranking the engine
with the starter, without actually starting the engine.
Not cranking-atmospheric
pressure

Cranking-intake air pressure It
changes at the value whitch is
smaller than in the atomo-
spheric pressure.
05Intake temperatureDisplays the intake air temperature.
* Check the temperature in the air cleaner case.Compare it to the value
displayed on the meter.
06Coolant temperatureDisplays the coolant temperature.
* Check the temperature of the coolant.Compare it to the value
displayed on the meter.
07
Vehicle speed pulseDisplays the accumulation of the vehicle pulses that are
generated when the tire is spun.(0
999; resets to 0 after 999)
OK if the numbers appear on
the meter.
08Lean angle cut-off
switchDisplays the lean angle cut-off switch values.Upright: 0.4
1.4 V
Overturned: 3.7
4.4 V
09Fuel system voltage
(battery voltage)Displays the fuel system voltage (battery voltage).
Engine stop switch is on.0
18.7 V
Normally, approximately 12.0 V
20Sidestand switchDisplays that the switch is ON or OFF. (When the gear is in a
position other than neutral.)Stand retracted: ON
Stand extended: OFF
21Neutral switchDisplays that the switch is ON or OFF.Neutral: ON
In gear: OFF
30
Ignition coil #1After the engine stop switch has been turned from OFF to
ON, it actuates ignition coil #1 for five times every second
and illuminates the engine trouble warning light.
* Connect an ignition checker.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check that spark is generated,
5 times with the engine stop
switch ON.
31
Ignition coils #2After the engine stop switch has been turned from OFF to
ON, it actuates ignition coil #2 for five times every second
and illuminates the engine trouble warning light.
* Connect an ignition checker.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check that spark is generated,
5 times with the engine stop
switch ON.
ProCarManuals.com

7-13
FUEL INJECTION SYSTEMFI
Diagnostic
codeItemDescription of actionData displayed on meter
(reference value)
32
Ignition coil #3After the engine stop switch has been turned from OFF to
ON, it actuates ignition coil #3 for five times every second
and illuminates the engine trouble warning light.
* Connect an ignition checker.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check that spark is generated,
5 times with the engine stop
switch ON.
33
Ignition coil #4After the engine stop switch has been turned from OFF to
ON, it actuates ignition coil #4 for five times every second
and illuminates the engine trouble warning light.
* Connect an ignition checker.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check that spark is generated,
5 times with the engine stop
switch ON.
36
Injector #1After the engine stop switch has been turned from OFF to
ON, it actuates the injector #1 five times every second and
illuminates the engine trouble warning light.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the operating sound of
the injector five times with
engine stop switch ON.
37
Injector #2After the engine stop switch has been turned from OFF to
ON, it actuates the injector #2 five times every second and
illuminates the engine trouble warning light.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the operating sound of
the injector five times with
engine stop switch ON.
38
Injector #3After the engine stop switch has been turned from OFF to
ON, it actuates the injector #3 five times every second and
illuminates the engine trouble warning light.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the operating sound of
the injector five times with
engine stop switch ON.
39
Injector #4After the engine stop switch has been turned from OFF to
ON, it actuates the injector #4 five times every second and
illuminates the engine trouble warning light.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the operating sound of
the injector five times with
engine stop switch ON.
48
AI system solenoidAfter the engine stop switch has been turned from OFF to
ON, it actuates the AI system solenoid five times every
second and illuminates the engine trouble warning light.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the operating sound of
the AI system solenoid 5 times
with the engine stop
switch ON.
50
Fuel injection system
relayAfter the engine stop switch has been turned from OFF to
ON, it actuates the fuel injection system relay five times
every second and illuminates the engine trouble warning
light (the light is OFF when the relay is ON, and the light is
ON when the relay is OFF).
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the fuel injection system
relay operating sound 5 times
with the engine stop
switch ON.
51
Radiator fan motor
relayAfter the engine stop switch has been turned from OFF to
ON, it actuates the radiator fan motor relay five times every
5 seconds and illuminates the engine trouble warning light.
(ON 2 seconds, OFF 3 seconds)
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the radiator fan motor
relay operating sound 5 times
with the engine stop
switch ON.
(At that time, the fan motor
rotates.)
ProCarManuals.com