AUX YAMAHA YZF-R1SC 2004 Service Manual

2-15
ELECTRICAL SPECIFICATIONSSPEC
ELECTRICAL SPECIFICATIONS
ItemStandardLimit
System voltage12 V



Ignition system
Ignition system type
Ignition timing
Crankshaft position sensor
resistance / color
T.C.I. unit model (manufacturer)
DC. T.C.I.
5 BTDC at 1,050 r / min
336  504 Ω at 20C (68F) / Gy-B
F8T822 (MITSUBISHI) (USA)
F8T823 (MITSUBISHI) (CAL)



















Ignition coils
Model (manufacturer)
Minimum ignition spark gap
Primary coil resistance
Secondary coil resistance
F6T558 (MITSUBISHI)
6 mm (0.24 in)
1.19  1.61 Ω at 20C (68F)
8.5  11.5 kΩ at 20C (68F)















Charging system
System type
Model (manufacturer)
Normal output
Stator coil resistance / color
A.C. magneto
F4T850 (MITSUBISHI)
14 V / 560 W at 5,000 r / min
0.14  0.18 Ω at 20C (68F) / W-W















Rectifier / regulator
Regulator type
Model (manufacture)
Semi conductor short circuit
FH011AA (SHINDENGEN)







()
No-load regulated voltage
Rectifier capacity
Withstand voltage
()
14.3  15.1 V
50 A
100 V











Battery
Battery type
Battery voltage / capacity
Specific gravity
Manufacturer
Ten hour rate amperage
YTZ10S
12 V / 8.6 Ah
1.310
YUASA
0.8 A



















Headlight typeHalogen bulb
Bulbs (voltage / wattage
quantity)
Headlight
Auxiliary light
Tail / brake light
Front turn signal light / position light
Rear turn signal light
Licence plate light
Meter light
12 V 55 W
4
12 V 5 W
2
LED
1
12 V 21 W / 5 W
2
12 V 21 W
2
12 V 5 W
1
LED
1



























ProCarManuals.com

2-35
CABLE ROUTINGSPEC
G Clamp the head light lead by
wrapping and insert it to the in-
take air grill hole. (only at the
right side.)
H Do not connect the wire to the
coupler with the plug for options.
I To the turn signal light
J To the wire harness
K Cut the tip of the clamp.A Insert to the rib of the head light.
(Either location of the right and
left relays is acceptable.)
B The lead should not stretch too
much.
C Make sure to insert the coupler
and boot to the stay 1 hole.
D The speedometer lead should
not be strained.
E To the stay 1 hole
F Connect after passing over the
upper side of the duct.1Ground lead
2Meter lead
3Stay 1
4Auxiliary light lead (right)
5Headlight lead
6Auxiliary light lead (left)
7Console panel 1
8Duct 1
9Console panel 2
10Duct 2
11Headlight lead (right)
12Headlight lead (left)
EAS00035
CABLE ROUTING
ProCarManuals.com

8-28
LIGHTING SYSTEMELEC
1Main switch
4Fuse (main)
6Battery
14E.C.U.
46Hi beam indicator light
49Meter light
57Dimmer switch
62Front turn signal/position light (left)
63Front turn signal/position light (right)
66Headlight
67Auxiliary light
68License plate light
69Rear brake light switch
70Tail/brake light
71Headlight relay (on / off)
72Headlight relay (dimmer)
74Fuse (signal)
75Fuse (headlight)
ProCarManuals.com

8-33
LIGHTING SYSTEMELEC
EAS00791
4. The auxiliary light fails to come on.
YESNO 1. Auxiliary light and socket

Check the auxiliary light bulb and socket for
continuity.
Refer to “CHECKING THE BULBS AND
BULB SOCKETS”.

Are the auxiliary light .bulb and socket OK?
Replace the auxiliary
light bulb, socket or
both.
YESNO 2. Voltage

Connect the pocket tester (DC 20 V) to the
auxiliary light coupler (auxiliary light side) as
shown.
The wiring circuit
from the main switch
to the auxiliary light
coupler is faulty and
must be repaired. Positive tester probe
blue / red
Negative tester probe
black
1

Turn the main switch to “ON”.

Measure the voltage (DC 12 V) of blue / red
on the auxiliary light coupler (auxiliary
light side).

Is the voltage within specification?
2
This circuit is OK.
2
5. The turn signa l/ position light fails to come on.
YESNO 1. Turn signal / position light and socket

Check the turn signal / position light bulb and
socket for continuity.
Refer to “CHECKING THE BULBS AND
BULB SOCKETS”.

Are the turn signal / position light bulb and
socket OK?
Replace the turn sig-
nal / position light
bulb, socket or both.
YESNO 2. Voltage

Connect the pocket tester (DC 20 V) to the
turn signal / position light coupler (wire har-
ness side) as shown.
The wiring circuit from
the main switch to the
turn signal / position
light coupler is faulty
and must be repaired.
Turn the main switch to “ON”.

Measure the voltage (DC 12 V) of blue or
blue on the turn signal / position light cou-
pler (wire harness side).

Is the voltage within specification?
3
This circuit is OK.
Left turn signal / position light
Positive tester probe
blue
Negative tester probe
black
Right turn signal / position light
Positive tester probe
blue
Negative tester probe
black
1
2
A
Left turn signal / position light
Right turn signal / position light
B
A
B
3
4
1
ProCarManuals.com

59Clutch switch
60Turn signal switch
61Horn
62Front turn signal / position light (left)
63Front turn signal / position light (right)
64Rear turn signal light (left)
65Rear turn signal light (right)
66Headlight
67Auxiliary light
68License plate light
69Rear brake light switch
70Tail / brake light
71Headlight relay (on / off)
72Headlight relay (dimmer)
73Fuse (ignition)
74Fuse (signal)
75Fuse (headlight)
76Radiator fan motor relay
77Fuse (radiator fan motor left)
78Fuse (radiator fan motor light)
79Radiator fan motor 2
80Radiator fan motor 1
81Ground
COLOR CODE
B Black. . . . .
Br Brown. . . .
Ch Chocolate. . .
Dg Dark green. . .
G Green. . . .
Gy Gray. . .
L Blue. . . . .
Lg Light green. . . .
O Orange. . . .
P Pink. . . . .
R Red. . . . .
Sb Sky blue. . . .
W White. . . .
Y Yellow. . . . .
B / G Black / Green. .
B / L Black / Blue. . .
B / R Black / Red. .
B / W Black / White. .
B / Y Black / Yellow. .
Br / G Brown / Green.
Br / L Brown / Blue. .
Br / R Brown / Red. .
Br / W Brown / White.
G / B Green / Black. .
G / R Green / Red. .
G / W Green / White. . G / Y Green / Yellow. .
Gy / B Gray / Black.
Gy / G Gray / Green.
Gy / R Gray / Red.
L / B Blue / Black. . .
L / R Blue / Red. .
L / W Blue / White. .
L / Y Blue / Yellow. . .
O / B Orange / Black. .
O / G Orange / Green. .
P / W Pink / White. .
R / B Red / Black. .
R / G Red / Green. .
R / L Red / Blue. .
R / W Red / White. .
R / Y Red / Yellow. .
Sb / W Sky blue / White.
W / B White / Black. .
W / R White / Red. .
W / Y White / Yellow. .
Y / B Yellow / Black. .
Y / G Yellow / Green. .
Y / L Yellow / Blue. . .
Y / R Yellow / Red. .
Y / W Yellow / White. .
YZF-R1S / YZF-R1SC WIRING DIAGRAM
1Main switch
2A.C. magneto
3Rectifier / regulator
4Fuse (main)
5Fuse (backup)
6Battery
7Fuse (fuel injection)
8Starter relay
9Starter motor
10Starting circuit cut-off relay
11Neutral switch
12Sidestand switch
13Fuel pump
14E.C.U
15Ignition coil #1
16Ignition coil #2
17Ignition coil #3
18Ignition coil #4
19Spark plug
20Injector #1
21Injector #2
22Injector #3
23Injector #4
24Air induction system solenoid
25Sub-throttle position sensor
26EXUP servo motor
27Speed sensor
28Coolant temperature sensor
29Intake air temperature sensor
30Option switch
31Crankshaft position sensor
32Throttle position sensor
33Intake air pressure sensor
34Atmospheric pressure sensor
35Cylinder identification sensor
36Lean angle cut-off switch
37Meter assembly
38Fuel level warning light
39Oil level warning light
40Neutral indicator light
41Tacho meter
42Shift timing indicator light
43Multi function meter
44Engine trouble warning light
45Coolant temperature indicator light
46Hi beam indicator light
47Turn signal indicator light (left)
48Turn signal indicator light (light)
49Meter light
50Oil level switch
51Right handlebar switch
52Front brake light switch
53Engine stop switch
54Start switch
55Turn signal relay
56Left handlebar switch
57Dimmer switch
58Horn switch
ProCarManuals.com