set clock YAMAHA YZF-R1SC 2004 Service Manual

1-2
1
1 Clock
2 Speedometer
3 “SELECT” button
4 “RESET” button
5 Tachometer
6 Coolant temperature display / air intake
temperature display
7 Odometer / tripmeters / fuel reserve tripme-
ter / stopwatch
8 Shift timing indicator light
1 Clock
2 Speedometer
FEATURES
GEN
INFO
NOTE:
EAS00019
FEATURES
INSTRUMENT FUNCTIONS
Multi-function display
The multi-function meter unit is equipped with
the following:

a speedometer (which shows the riding
speed)

a tachometer (witch shows engine speed)

an odometer (which shows the total distance
traveled)

two tripmeters (which show the distance
traveled since they were last set to zero)

a fuel reserve tripmeter (which shows the
distance traveled since the fuel level warning
light came on)

a stopwatch

a clock

a coolant temperature display

an air intake temperature display

a self-diagnosis device

a display brightness and shift timing indicator
light control mode

Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons.
Clock mode
Turn the key to “ON”.
To set the clock
1. Push the “SELECT” button and “RESET”
button together for at least two seconds.
2. When the hour digits start flashing, push the
“RESET” button to set the hours.
3. Push the “SELECT” button, and the minute
digits will start flashing.
4. Push the “RESET” button to set the minutes.
5. Push the “SELECT” button and then release
it to start the clock.
ProCarManuals.com

3-19
SYNCHRONIZING THE THROTTLE BODIES /
ADJUSTING THE EXHAUST GAS VOLUMECHK
ADJ
NOTE:
NOTE: 9. Measure:

engine idling speed
Out of specification
Adjust.
Make sure that the vacuum pressure is within
specification.
10. Stop the engine and remove the measuring
equipment.
11. Adjust:

throttle cable free play
Refer to “ADJUSTING THE THROTTLE
CABLE FREE PLAY”.
Throttle cable free play
(at the flange of the throttle grip)
3  5 mm (0.12  0.20 in)
13. Install:

synchronizing hoses

fuel tank
Refer to “FUEL TANK”.

rider seat
Refer to “SEATS”.
ADJUSTING THE EXHAUST GAS VOLUME
Be sure to set the carbon monoxide density to
standard, and then adjust the exhaust gas.
1. Turn the main switch to “OFF” and engine
stop switch “ON”.
2. While keeping the “SELECT” and “RESET”
buttons pressed simultaneously, turn “ON”
the main switch (keep them pressed for 8 se-
conds or more).
All indications on the meter disappear except
the clock and trip indications.
Letters “dIAG” appear on the clock LCD.
ProCarManuals.com

3-20
ADJUSTING THE EXHAUST GAS VOLUME
CHK
ADJ
NOTE:
NOTE: 3. Using the “SELECT” button, select either the
Co adjustment mode
1 (which appears as
“Co”) or the diagnosis mode (which appears
as “dIAG”).
4. After “Co” appears as a result of pressing the
“SELECT” button, simultaneously press the
“SELECT” and “RESET” buttons for 2 se-
conds or more to excute the selection.
5. Press the “SELECT” and “RESET” buttons to
select the cylinder
2.

The adjustment cylinder appears on the clock
LCD.
“RESET” button = decrement
“SELECT” button = increment
6. Excute the selection of the cylinder by simul-
taneously pressing the “SELECT” and “RE-
SET” buttons for approximately 2 seconds.
7. After selecting the adjustment cylinder,
change the “Co” adjustment volume by
pressing the “SELECT” and “RESET” but-
tons.
The Co adjustment volume appears on the trip
LCD.
“RESET” button = decrement
“SELECT” button = increment
8. The selection is executed upon releasing the
finger from the switch.
9. Simultaneously press the “SELECT” and
“RESET” buttons to return to the cylinder
selection. (step 5)
10. Cancel the mode by turning “OFF” the main
switch.
ProCarManuals.com

3-68
CHECKING THE FUSES
CHK
ADJ
WARNING
Pocket tester
90890-03112, YU-3112
b. If the pocket tester indicates “∞”, replace the
fuse.
3. Replace:

blown fuse
a. Set the main switch to “OFF”.
b. Install a new fuse of the correct amperage
rating.
c. Set on the switches to verify if the electrical
circuit is operational.
d. If the fuse immediately blows again, check
the electrical circuit.
Fuses
Amperage
ratingQ’ty
Main50 A1
Fuel injection
system15 A1
Headlight25 A1
Signaling
system10 A1
Ignition15 A1
Backup fuse
(odometer
and clock)
10 A1
Radiator
fan motor15 A2
Reserve25 A, 15 A,
10 A1
Never use a fuse with an amperage rating
other than that specified. Improvising or us-
ing a fuse with the wrong amperage rating
may cause extensive damage to the electri-
cal system, cause the lighting and ignition
systems to malfunction and could possibly
cause a fire.
4. Install:

front cowling inner panel (left)
Refer to “COWLINGS”.

rider seat
Refer to “SEATS”.
ProCarManuals.com

7-8
FUEL INJECTION SYSTEMFI
NOTE:
NOTE:
EAS00905
DIAGNOSTIC MODE
It is possible to monitor the sensor output data
or check the activation of actuators without con-
necting the measurement equipment by simply
switching the meter indication from the normal
mode to the diagnostic monitoring mode.
Setting the diagnostic mode
1. Turn the main switch to “OFF” and set the en-
gine stop switch to “OFF”.
2. Disconnect the wire harness coupler from
the fuel pump.
3. Simultaneously press and hold the “SE-
LECT” and “RESET” buttons, turn the main
switch to “ON”, and continue to press the but-
tons for 8 seconds or more.

All displays on the meter disappear except the
clock and tripmeter displays.

“dIAG” appears on the LCD meter.
4. Press the “SELECT” button to select the CO
adjustment mode “Co” or the diagnostic
mode “dIAG”.
5. After selecting “dIAG”, simultaneously press
the “SELECT” and “RESET” buttons for 2 se-
conds or more to execute the selection.
6. Select the diagnostic code number that ap-
plies to the item that was verified with the
fault code number by pressing the “SELECT”
and “RESET” buttons.

The diagnostic code number appears on the
LCD meter (01-70).

To decrease the selected diagnostic code
number, press the “RESET” button. Press the
“RESET” button for 1 second or longer to auto-
matically decrease the diagnostic code num-
bers.

To increase the selected diagnostic code num-
ber, press the “SELECT” button. Press the
“SELECT” button for 1 second or longer to au-
tomatically increase the diagnostic code num-
bers.
ProCarManuals.com