engine oil YAMAHA YZF-R6 2000 User Guide
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2000, Model line: YZF-R6, Model: YAMAHA YZF-R6 2000Pages: 111, PDF Size: 11.91 MB
Page 62 of 111
PERIODIC MAINTENANCE AND MINOR REPAIR
6-12
6 7. Apply a light coat of engine oil to
the O-ring of the new oil filter.
NOTE:@ Make sure the O-ring is seated proper-
ly. @
8. Install the oil filter and tighten it to
the specified torque with an oil fil-
ter wrench.9. Fill the engine with sufficient oil to
reach the specified level. Install
the engine oil filler cap and tighten
it.
EC000066
CAUTION:@ l
Do not put in any chemical addi-
tives. Engine oil also lubricates
the clutch and additives could
cause clutch slippage.
l
Be sure no foreign material en-
ters the crankcase.
@
1. O-ring
1. Torque wrenchTightening torque:
Oil filter:
17 Nm (1.7 m·kg)
Recommended oil:
See page 8-1.
Oil quantity:
Total amount:
3.5 L
Periodic oil change:
2.5 L
With oil filter replacement:
2.7 L
E_5eb_Periodic.fm Page 12 Thursday, November 18, 1999 4:06 PM
Page 63 of 111
PERIODIC MAINTENANCE AND MINOR REPAIR
6-13
610. Start the engine and warm it up for
several minutes. While warming
up, check for oil leakage. If oil
leakage is found, stop the engine
immediately and check for the
cause.
11. After the engine is started, the oil
level indicator light should go off if
the oil is at the specified level.
EC000067
CAUTION:@ If the indicator light flickers or re-
mains on, immediately stop the en-
gine and consult with a Yamaha
dealer. @12. Install the cowling.
EAU01611
Cooling system1. Check the coolant level in the res-
ervoir tank when the engine is cold
as the coolant level will vary with
engine temperature. The coolant
level should be between the maxi-
mum and minimum marks.2. If the level is low, remove the res-
ervoir tank cover by removing the
bolts.
3. Add coolant or distilled water to
raise it to the specified level.
4. Install the reservoir tank cover and
bolts.1. Maximum level mark
2. Minimum level mark
1. Bolt (´ 2)
Reservoir tank capacity:
0.44 L
E_5eb_Periodic.fm Page 13 Thursday, November 18, 1999 4:06 PM
Page 79 of 111
PERIODIC MAINTENANCE AND MINOR REPAIR
6-29
6
EAU01251
Drive chain slack adjustment1. Loosen the axle nut.
2. Loosen the locknuts on each side.
To tighten the chain, turn the chain
adjusting bolts in direction
a. To
loosen the chain, turn the adjust-
ing bolts in direction
b and push
the wheel forward. Turn each ad-
justing bolt exactly the same
amount to maintain correct axle
alignment. There are marks on
each side of the swingarm. Use
these marks to align the rear
wheel.
EC000096
CAUTION:@ Too little chain slack will overload
the engine and other vital parts.
Keep the slack within the specified
limits. @3. After adjusting, tighten the lock-
nuts. Then tighten the axle nut to
the specified torque.
EAU03006
Drive chain lubricationThe chain consists of many parts which
work with each other. If the chain is not
maintained properly, it will wear out
quickly. Therefore, the chain must be
serviced regularly. This service is es-
pecially necessary when riding in dusty
areas. This motorcycle is equipped
with a sealed type chain. Steam clean-
ing, high-pressure washers, and sol-
vents can damage the drive chain, so
do not use these for cleaning it. Use
only kerosene to clean the drive chain.
Wipe it dry, and thoroughly lubricate it
with SAE 30 ~ 50W motor oil. Do not
use any other lubricants on the drive
chain. They may contain solvents that
could damage the sealed chain.
EC000097
CAUTION:@ Be sure to oil the chain after wash-
ing the motorcycle or riding in the
rain. @
1. Axle nut
2. Adjusting bolt
3. Locknut
4. Alignment marks
Tightening torque:
Axle nut:
150 Nm (15.0 m·kg)
E_5eb_Periodic.fm Page 29 Thursday, November 18, 1999 4:06 PM
Page 80 of 111
PERIODIC MAINTENANCE AND MINOR REPAIR
6-30
6
EAU02962
Cable inspection and
lubrication
EW000112
WARNING
@ Damage to the outer housing of ca-
bles may lead to internal rusting and
interfere with the cable movement.
Replace damaged cables as soon as
possible to prevent unsafe condi-
tions. @Lubricate the cables and cable ends. If
a cable does not operate smoothly, ask
a Yamaha dealer to replace it.
EAU00773
Throttle cable and grip
lubricationThe throttle twist grip assembly should
be greased at the time that the cable is
lubricated, since the grip must be re-
moved to get at the end of the throttle
cable. After removing the screws, hold
the end of the cable up in the air and
put in several drops of lubricant. With
the throttle grip disassembled, coat the
metal surface of the grip assembly with
a suitable all-purpose grease.
EAU01290*
Brake pedal lubricationLubricate the pivoting parts.
Recommended lubricant:
Engine oilRecommended lubricant:
Engine oil
E_5eb_Periodic.fm Page 30 Thursday, November 18, 1999 4:06 PM
Page 81 of 111
PERIODIC MAINTENANCE AND MINOR REPAIR
6-31
6
EAU02985
Brake and clutch lever
lubricationLubricate the pivoting parts.
EAU02986
Sidestand lubricationLubricate the sidestand pivoting point
and metal-to-metal contact surfaces.
Check that the sidestand moves up
and down smoothly.
EW000113
WARNING
@ If the sidestand does not move
smoothly, consult a Yamaha dealer. @
EAU00791
Rear suspension lubricationLubricate the pivoting parts.
Recommended lubricant:
Engine oil
Recommended lubricant:
Engine oil
Recommended lubricant:
Lithium soap base grease
E_5eb_Periodic.fm Page 31 Thursday, November 18, 1999 4:06 PM
Page 82 of 111
PERIODIC MAINTENANCE AND MINOR REPAIR
6-32
6
EAU02939
Front fork inspectionVisual check
EW000115
WARNING
@ Securely support the motorcycle so
there is no danger of it falling over. @Check for scratches or damage on the
inner tube and excessive oil leakage
from the front fork.
Operation check
1. Place the motorcycle on a level
place.
2. Hold the motorcycle in an upright
position and apply the front brake.
3. Push down hard on the handle-
bars several times and check if the
fork rebounds smoothly.
EC000098
CAUTION:@ If any damage or unsmooth move-
ment is found with the front fork,
consult a Yamaha dealer. @
EAU00794
Steering inspectionPeriodically inspect the condition of the
steering. Worn out or loose steering
bearings may be dangerous. Place a
stand under the engine to raise the
front wheel off the ground. Hold the
lower end of the front forks and try to
move them forward and backward. If
any free play can be felt, ask a Yamaha
dealer to inspect and adjust the steer-
ing. Inspection is easier if the front
wheel is removed.
EW000115
WARNING
@ Securely support the motorcycle so
there is no danger of it falling over. @
E_5eb_Periodic.fm Page 32 Thursday, November 18, 1999 4:06 PM
Page 97 of 111
MOTORCYCLE CARE AND STORAGE
7-3
71. Clean your motorcycle with cold
water and soap after the engine
has cooled down.
ECA00012
CAUTION:@ Do not use warm water since it in-
creases the corrosive action of the
salt. @2. Be sure to apply a corrosion pro-
tection spray on all (even chrome-
and nickel-plated) metal surfaces
to prevent corrosion.After cleaning
1. Dry the motorcycle with a chamois
or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)
4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all (even chrome-
and nickel-plated) metal surfaces.
5. Use spray oil as a universal clean-
er to remove any remaining dirt.
6. Touch up minor paint damage
caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely
before storing it or covering it.
EWA00001
WARNING
@ Make sure that there is no oil or wax
on the brakes and tires. If neces-
sary, clean the brake discs and lin-
ings with a regular brake disc
cleaner or acetone, and wash the
tires with warm water and mild soap.
Then, carefully test the motorcycle
for its braking performance and cor-
nering behavior. @
E_5eb_Cleaning.fm Page 3 Thursday, November 18, 1999 4:08 PM
Page 99 of 111
MOTORCYCLE CARE AND STORAGE
7-5
7a. Remove the spark plug caps and
spark plugs.
b. Pour a teaspoonful of engine oil
into each spark plug bore.
c. Install the spark plug caps onto the
spark plugs and place the spark
plugs on the cylinder head so that
the electrodes are grounded. (This
will limit sparking during the next
step.)
d. Turn the engine over several times
with the starter. (This will coat the
cylinder walls with oil.)
e. Remove the spark plug caps from
the spark plugs, install the spark
plugs and then the spark plug
caps.
EWA00003
WARNING
@ When turning the engine over, be
sure to ground the spark plug elec-
trodes to prevent damage or injury
from sparking. @
6. Lubricate all control cables and
the pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
7. Check and, if necessary, correct
the tire air pressure, then raise the
motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
8. Cover up the muffler outlet with a
plastic bag to prevent moisture
from entering.9. Remove the battery and fully
charge it. Store it in a cool, dry
place and recharge it once a
month. Do not store the battery in
an excessively cold or warm place
(less than 0°C or more than 30°C).
For more information, see “Battery
storage” in the chapter “PERIOD-
IC MAINTENANCE AND MINOR
REPAIRS”.
NOTE:@ Make any necessary repairs before
storing the motorcycle. @
E_5eb_Cleaning.fm Page 5 Thursday, November 18, 1999 4:08 PM
Page 101 of 111
8-1
8
EAU01038
8-SPECIFICATIONSSpecifications01E
Model YZF-R6
Dimensions
Overall length 2,025 mm (except for N, S, SF)
2,075 mm (for N, S, SF)
Overall width 690 mm
Overall height 1,105 mm
Seat height 820 mm
Wheelbase 1,380 mm
Ground clearance 135 mm
Minimum turning radius 3,400 mm
Basic weight (with oil and full
fuel tank)
188 kg
Engine
Engine type Liquid-cooled 4-stroke, DOHC
Cylinder arrangement Forward-inclined parallel
4-cylinder
Displacement 600 cm
3
Bore ´ Stroke 65.5 ´ 44.5 mm
Compression ratio 12.4:1
Starting system Electric starter
Lubrication system Wet sumpEngine oil
Ty p e
Recommended engine oil
classification API Service SE, SF, SG type or
higher
Quantity
Periodic oil change 2.5 L
With oil filter replacement 2.7 L
Total amount 3.5 L
-20˚ -10˚ 0˚
10˚20˚ 30˚
40˚50˚C
SAE 10W/30
SAE 15W/40SAE 20W/40SAE 20W/50
SAE 10W/40
CAUTION:Be sure to use motor oils that do not contain anti-fric-
tion modifiers. Passenger car motor oils (often labeled
“Energy Conserving”) contain anti-friction additives
which will cause clutch and/or starter clutch slippage,
resulting in reduced component life and poor engine
performance.
E_5eb_Spec.fm Page 1 Thursday, November 18, 1999 4:08 PM
Page 109 of 111
10-INDEXAAir filter .................................................. 6-17
Air intake duct ........................................ 6-19
Antitheft alarm (optional) ........................ 3-12BBattery ................................................... 6-33
Brake and clutch lever lubrication........... 6-31
Brake fluid replacement ......................... 6-28
Brake light switch adjustment ................. 6-25
Brake pedal lubrication........................... 6-30CCable inspection and lubrication ............ 6-30
Carburetor adjustment ........................... 6-20
Care.........................................................7-1
Changing the coolant ............................. 6-14
Checking the front and rear brake
pads .................................................... 6-26
Clutch lever ............................................ 3-11
Clutch lever free play adjustment ........... 6-25
Controls/Instruments ................................2-3
Cooling system ...................................... 6-13
Cowling and panel removal and
installation .............................................6-6
Cowlings A and B ....................................6-6DDiagnosis device......................................3-9
Digital speedometer .................................3-7
Dimmer switch .........................................3-9
Drive chain lubrication ............................ 6-29
Drive chain slack adjustment.................. 6-29
Drive chain slack check.......................... 6-28
EEngine break-in ....................................... 5-5
Engine oil .............................................. 6-10
Engine stop switch................................. 3-10FFront brake lever ................................... 3-11
Front fork adjustment............................. 3-17
Front fork inspection .............................. 6-32
Front wheel installation .......................... 6-38
Front wheel removal .............................. 6-37
Fuel ....................................................... 3-13
Fuel indicator light ................................... 3-2
Fuel indicator light circuit check ............... 3-6
Fuel tank breather hose ......................... 3-14
Fuel tank cap ......................................... 3-13
Fuse replacement.................................. 6-34GGive safety the right of way ..................... 1-1HHandlebar switches ................................. 3-9
Dimmer switch ................................... 3-9
Engine stop switch ........................... 3-10
Horn switch ...................................... 3-10
Light switch ...................................... 3-10
Pass switch ........................................ 3-9
Start switch ...................................... 3-10
Turn signal switch ............................ 3-10
Headlight bulb replacement ................... 6-35
Helmet holder ........................................ 3-17
High beam indicator light ......................... 3-2
Horn switch ........................................... 3-10
IIdentification number records ...................9-1
Idle speed adjustment ............................6-20
Indicator lights ..........................................3-2
Fuel indicator light...............................3-2
High beam indicator light ....................3-2
Neutral indicator light ..........................3-2
Oil level/coolant temperature
indicator light....................................3-3
Turn indicator light ..............................3-2
Inspecting the brake fluid level ...............6-27KKey identification number .........................9-1LLeft view...................................................2-1
Light switch ............................................3-10
Luggage strap holders ...........................3-23MMain switch/Steering lock .........................3-1
Model label ..............................................9-2NNeutral indicator light ...............................3-2OOil level/coolant temperature indicator
light ........................................................3-3
Oil level / coolant temperature indicator
light circuit check ...................................3-5PPanel C ....................................................6-8
Parking.....................................................5-5
E_5ebIX.fm Page 1 Thursday, November 18, 1999 4:09 PM