reset Abarth Punto Evo 2010 Owner handbook (in English)

6
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U005Abfig. 4
KEY WITH REMOTE CONTROL fig. 4
The metal insert A operates:
❒the ignition switch;
❒the door locks;
❒the fuel cap lock/release (for versions/markets where
provided);
Pressing button B opens/closes the metal insert.
All the keys and the CODE card must be
handed over to the new owner when
selling the car.
Button B should only be pressed when
the key is away from the body, in
particular from the eyes and from objects that
can be spoilt (e.g. clothes). Never leave the key
unattended and make sure it can never be
touched by others, especially children, who may
inadvertently press the button.
WARNING
Button Ëis used for unlocking the doors and the boot.
Button Áis used for locking the doors and the boot.
Button
Ris used to open the boot remotely.
When unlocking the doors, the passenger compartment
ceiling lights will come on for a preset time.
001-028 GPUNTO EVO Abarth GB 2ed 30-04-2010 16:26 Pagina 6

27
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
BUTTON VOLUME
(Adjusting the button volume)
This function may be used to adjust (to 8 levels) the
volume of the noise made when the MENU ESC, +e –
buttons are pressed.
To set the desired volume, proceed as follows:
– briefly press MENU ESC: the previously set volume
level will flash on the display;
– press the button +or –for setting;
– briefly press the MENU ESC button to go back to the
menu screen or hold the button down to go back to the
standard screen without saving.
SEAT BELT BUZZ
(SBR buzzer reactivation)
(for versions/markets where provided)
This function can only be displayed after Abarth
Dealership has deactivated the SBR system (see
paragraph “SBR system” in section “Safety devices”).SERVICE (Scheduled servicing)
Using this function you can display information about
the mileage intervals for car servicing.
To consult this display, proceed as follows:
– briefly press MENU ESC: service intervals in km or mi,
depending on the previous setting, will be displayed (see
“Measurement units”);
– press the MENU ESC button briefly to return to the
menu screen or hold the button down to return to the
standard screen.
Note The “Scheduled Servicing Plan” requires the
vehicle to be serviced every 15,000 km (or 9,000 mi).
This indication will appear automatically, with the key in
MAR position, starting from 2,000 km (or 1,240 mi)
when the next service is due and will be displayed again
every 200 km (or 124 mi). Below 200 km servicing
indications are more frequent. The displaying will be in
kilometres or miles depending on the measurement unit
settings. When the next scheduled service is
approaching and the key is turned to MAR, the word
Service will appear on the display, followed by the
number of kilometres or miles left. Go to an Abarth
Dealership, where the “Scheduled Servicing Plan”
operations will be performed and the message will be
reset.
001-028 GPUNTO EVO Abarth GB 2ed 30-04-2010 16:26 Pagina 27

29
Values displayed
Outside temperature
Indicates the temperature outside the vehicle passenger
compartment.
Range
This indicates the approximate distance that may be
travelled with the fuel remaining in the tank, assuming
that driving conditions do not change. The display will
show the reading
“----“ when the following events take place:
– range value lower than 50 km (or 30 mi)
– car parked with engine running for a long period.
Distance travelled
This value shows the distance covered from the start of
the new journey.
Average consumption
This value shows the approximate average fuel
consumption from the start of the new journey.
Current consumption
This indicates the fuel consumption. The value is
constantly updated. The display will show “----” if the
car is parked with the engine running.
Average speed
This value shows the car’s average speed as a function
of the overall time elapsed since the start of the new
mission.TRIP COMPUTER
General information
The Trip computer is used to display information on car
operation when the key is turned to MAR. This function
is made up of two separate trips called “Trip A” and
“Trip B” which can monitor the car’s “complete mission”
independently of each other. Both functions can be
zeroed
(reset - start of a new journey).
“Trip A” is used to display the figures relating to:
– Outside temperature
– Range
– Trip distance
– Average consumption
– Current consumption
– Average speed
– Trip time (driving time).
Trip B allows the display of the following parameters:
– Trip distance B
– Average consumption B
– Average speed B
– Trip time B (driving time).
N.B. “Trip B” may be disabled (see “Activating Trip B”).
“Range” and “Instantaneous consumption” cannot be
reset.
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
029-068 GPUNTO EVO Abarth GB 2ed 23-04-2010 13:33 Pagina 29

30
F0U018Abfig. 19
New mission
This begins after a reset:
– “manual” resetting by the user, by pressing the
relevant button;
– “automatic” resetting, when the distance travelled
reaches 99,999.9 km or when the journey time reaches
99.59 (99 hours and 59 minutes);
– disconnection/reconnection of the battery.
IMPORTANT The reset operation when “Trip A”
details are being displayed resets the information
associated with this function only.
IMPORTANT The reset operation when “Trip B”
details are being displayed resets the information
associated with this function only.
Start of journey procedure
With the ignition key in the MAR position, reset by
pressing the TRIP button and keeping it pressed for
more than 2 seconds.
Exit Trip
To exit from the Trip function: keep MENU ESC
pressed for over 2 seconds. Trip time
Time elapsed since the start of the new journey.
IMPORTANT In the absence of information, Trip
Computer values are displayed with “----”. When
normal operating condition is restored, calculation of
different units will restart regularly. No values displayed
before the failure will be reset nor will a new mission
be started.
TRIP control button fig. 19
The TRIP button is located on the right hand lever.
With the ignition key turned to MAR, this button allows
you to view the previously described parameters and
reset them to begin a new mission:
– short press to display the different values;
– long press to reset and start a new mission.
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
029-068 GPUNTO EVO Abarth GB 2ed 23-04-2010 13:33 Pagina 30

54
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
❒move the stalk upwards (+) for at least one second,
then release it. The car speed is now memorised and
you can therefore release the accelerator pedal.
If needed (when overtaking for instance), you can
accelerate simply by pressing the accelerator pedal;
when you release the pedal, the car will return to the
speed memorised previously.
RESTORING THE MEMORISED SPEED
If the device has been switched off, for example by
depressing the brake or clutch pedal, the memorised
speed can be restored as follows:
❒accelerate gradually until reaching a speed
approaching the memorised speed;
❒engage the gear selected at the time of speed
memorisation;
❒press button RES B-fig. 39.CRUISE CONTROL
(for versions/markets where provided)
This is an electronically controlled device which allows
the vehicle to be driven at a chosen speed above 30
km/h on long stretches of dry, straight roads with few
variations (e.g. motorways), without having to depress
the accelerator pedal. It is therefore not recommended
to use this device on extra-urban roads with traffic. Do
not use it in town.
TURING THE DEVICE ON
Turn twist switch A-fig. 39 to ON.
The cruise control cannot be engaged in 1st or reverse
gear. It is advisable to engage it in 4th gear or higher.
When travelling downhill with the device engaged, the
vehicle speed may slightly exceed the preset one.
When the device is activated the warning light
Ücomes
on together with the relevant message on the
instrument panel.
SETTING VEHICLE SPEED
Proceed as follows:
❒turn twist switch A-fig. 39 to ON and press the
accelerator pedal until you reach the required speed;
F0U039Abfig. 39
029-068 GPUNTO EVO Abarth GB 2ed 23-04-2010 13:33 Pagina 54

55
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
INCREASING THE MEMORISED SPEED
This can be done in two ways:
❒by pressing the accelerator and then memorising the
new speed reached;
or
❒moving the stalk upwards (+).
Each operation of the lever will correspond to a slight
increase in speed of about 1 km/h, while keeping the
lever upwards will increase the speed continuously.
REDUCING THE MEMORISED SPEED
This can be done in two ways:
❒by turning the device off and then storing a new
speed;
or
❒by moving the stalk downwards (–) until reaching the
new speed which will be memorised automatically.
Each movement of the lever will correspond to a slight
reduction in speed of about 1 km/h, while keeping the
lever held downwards will decrease the speed
continuously.
TURNING THE DEVICE OFF
The device can be switched off by the driver in the
following ways:
❒turning twist switch A to OFF;
❒switching off the engine;
❒pressing the brake pedal;❒pressing the clutch pedal;
❒pressing the accelerator pedal; in this case, the
system is not really switched off but the request for
acceleration takes priority. The cruise control is,
however, active and you do not need to press
button RES B-fig. 39 to restore the previous
conditions when you have finished accelerating.
The device is automatically switched off in the following
cases:
❒if the ABS or ESP systems cut in;
❒if the car speed drops below the preset limit;
❒if there is a system failure.
While travelling with the device engaged, do
not put the gear lever into neutral.
WARNING
In the event of malfunction or if the device
fails, turn twist switch A to OFF and contact an
Abarth Dealership.
WARNING
029-068 GPUNTO EVO Abarth GB 2ed 23-04-2010 13:33 Pagina 55

104
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
CD CHANGER CAPABILITY
(for versions/markets where provided)
The system consists of:
❒power cables;
❒connection cables.
For connection to the preset cables,
contact an Abarth Dealership to prevent
any problem that could impair car safety.
WARNING
When the SHIFT UP icon (NSHIFT) is shown on the
display, the “e-GSI” system is advising the driver to
select a higher gear, while the SHIFT DOWN
(
OSHIFT) icon suggests that a lower gear should be
engaged.
Note The “e-GSI” system intervenes only when the
“Normal” driving mode is activated (see the “Manettino
Abarth car dynamic control system (DSS – Driving
Sport Switch)” paragraph in this section).
069-108 GPUNTO EVO Abarth GB 2ed 23-04-2010 13:36 Pagina 104

149
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
TYRE PRESSURE CHECK
(amber)
TYRE PRESSURE LOW (amber)
TYRE PRESSURE UNSUITABLE FOR
SPEED
(amber)
(for versions/markets where provided)
Check tyre pressures
The symbol is shown on the display to indicate the flat
tyre. Should two or more tyres be flat, the display will
show the indications corresponding to each tyre in
sequence.
Restore correct tyre pressures as soon as possible (see
“Cold tyre pressures” in the “Technical specifications”
section).
Tyre pressure low
The symbol is shown on the display if the pressure of
one or more tyres drops below the preset level. In this
way the TPMS system warns the driver that one or
more tyres may be dangerously flat and liable to
puncture.
n
IMPORTANT Do not continue driving with one or
more flat tyres as handling may be compromised. Stop
the car, avoiding harsh braking or steering manoeuvres.
Repair using the dedicated kit (see the “Automatic
Fix&Go quick tyre repair kit” paragraph in the “In an
emergency” section) and contact an Abarth Dealership
as soon as possible.
Tyre pressure unsuitable for speed
Should travelling at a higher speed than 160 km/h be
required, inflate tyres to pressures values specified in
paragraph “Inflation pressures”.
If the TPMS system (where provided) detects that the
pressure of one or more tyres is unsuitable for the
current speed, the symbol will be shown on the display
together with the dedicated message (see paragraph
“Low tyre pressure” in this section) and it will stay on
until the car speed returns within the preset threshold.
IMPORTANT In this case, slow down immediately
because tyre overheating could compromise tyre
performance and durability beyond repair, and may even
make the tyre explode.
141-150 GPUNTO EVO Abarth GB 2ed 23-04-2010 14:04 Pagina 149

Selecting a frequency band ........................................... 244
Preselection buttons ..................................................... 245
Storing the last station listened to ............................. 245
Automatic tuning ............................................................ 245
Manual tuning .................................................................. 245
Autostore function ........................................................ 246
Emergency alarm reception ......................................... 247
EON function ................................................................. 247
Stereophonic broadcasters .......................................... 247
CD PLAYER .................................................................... 248
Introduction .................................................................... 248
CD player selection ....................................................... 248
CD loading/ejection ....................................................... 249
Display readings .............................................................. 250
Track selection ................................................................ 250
Fast forward/rewind through tracks .......................... 250
Pause function ................................................................. 250
CD MP3 PLAYER ........................................................... 251
Introduction .................................................................... 251
MP3 mode ....................................................................... 251
Selection of MP3 sessions with hybrid discs ............ 252
Display readings .............................................................. 252
Selection of next/previous folder ............................... 253
Folder structure ............................................................. 253
TROUBLESHOOTING ............................................... 254
RADIO
INTRODUCTION ........................................................ 222
Suggestions ...................................................................... 222
Technical specifications ................................................. 224
QUICK GUIDE .............................................................. 225
Steering wheel controls ................................................ 228
General information ...................................................... 229
FUNCTIONS AND ADJUSTMENTS ........................ 231
Turning the car radio on .............................................. 231
Turning the car radio off .............................................. 231
Selecting the radio functions ....................................... 231
Selecting CD function ................................................... 231
Audio source memory function .................................. 231
Volume adjustment ........................................................ 232
Mute/Pause function ...................................................... 232
Audio adjustments ......................................................... 233
Tone adjustment ............................................................ 234
Balance adjustment ........................................................ 234
Fader adjustment ........................................................... 234
Loudness adjustment ..................................................... 234
Preset/User/Classic/Rock/Jazz functions ................... 235
User Eq Settings function ............................................. 235
Menu ................................................................................. 236
Phone set-up ................................................................... 242
Anti-theft protection ..................................................... 243
RADIO (Tuner) .............................................................. 244
Introduction .................................................................... 244
RADIO
221
221-258 GPUNTO EVO Abarth GB 2ed 30-04-2010 16:40 Pagina 221

Button
1 2 3 4 5 6
RADIO FUNCTIONS
Radio station search:
- Automatic search
- Manual search
Storing the current radio station
Stored station recall
Mode
Automatic search: pressing buttons ¯or ˙
(long press for fast forward)
Manual search: pressing buttons ▲or ▼
(long press for fast forward)
Long button press for memory preset
1 to 6 respectively
Short button press for memory preset
1 to 6 respectively
Button
MUTE
AUDIO
MENU
GENERAL FUNCTIONS
Volume activation/deactivation (Mute/Pause)
Audio adjustments: low tones (BASS), high tones
(TREBLE), RH / LH balance (BALANCE),
front / rear balance (FADER)
Advanced functions adjustment
Volume adjustment
Mode
Short button press
Menu activation: short button press
Adjustment type selection: buttons ▲or ▼
press Value adjustment: buttons ¯or ˙press
Menu activation: short button press
Adjustment type selection: buttons ▲or ▼
press Value adjustment: buttons ¯or ˙press
Left/right rotation of twist control
RADIO
226
221-258 GPUNTO EVO Abarth GB 2ed 30-04-2010 16:40 Pagina 226