trailer Abarth Punto Evo 2011 Owner handbook (in English)

136
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
DRIVING STYLE
Starting
Do not warm up the engine at low or high revs when
the car is stationary; this causes the engine to warm up
more slowly, thereby increasing fuel consumption and
emissions. It is therefore advisable to move off
immediately, slowly, avoiding high speeds: in this way the
engine will warm up more quickly.
Unnecessary actions
Avoid accelerating when stopped at traffic lights or
before switching off the engine. The latter action, like
double-clutching, is unnecessary and causes increase of
consumption and pollution.
Gear selection
As soon as the conditions of the traffic and road allow,
use a higher gear. Using a low gear for faster
acceleration will increase consumption. In the same way
improper use of a high gear increases consumption,
emissions and engine wear. Roof rack/ski rack
Remove the roof rack or the ski rack from the roof
after use. These accessories lower air penetration and
adversely affect consumption levels. When transporting
particularly large objects, use a trailer if possible.
Electrical devices
Use electrical devices only for the amount of time
needed. Rear heated window, additional headlights,
windscreen wipers and heater fan need a considerable
amount of energy, therefore increasing the requirement
of current increases fuel consumption (up to +25% in
the urban cycle).
Climate control system
The climate control system is an additional load which
greatly affects the engine leading to higher consumption
(on average up to +20%). When the temperature
outside the car permits it, use the air vents where
possible.
Devices for aerodynamic control
The use of non-certified devices for aerodynamic
control may adversely affect air drag and consumption
levels.

145
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Contact an Abarth Dealership as soon
as possible if the warning light Udoes
not light up when the key is turned to MAR or
if, during travel, the warning light comes on
either constantly or flashing (along with a
message on the display). The operation of the
warning light Umay be checked by the traffic
control authorities using specific devices. Always
comply with the traffic regulations in force in
the country where you are driving.
WARNING
If the light flashes, release the accelerator pedal to
reduce engine revs until the warning light stops flashing;
continue the journey at a moderate speed, trying to
avoid driving conditions that may cause further flashing,
and contact an Abarth Dealership as soon as possible.EXCESSIVE ENGINE COOLANT
TEMPERATURE (red)
When the key is turned to the MAR position
the warning light comes on but should go out after a
few seconds. The warning light turns on when the
engine is overheated. If the warning light comes on
when driving, proceed as follows:
❒when driving normally: stop the car, switch off the
engine and check that the water level in the
reservoir is not below the MIN mark. If it is not, wait
for a few minutes for the engine to cool down then
slowly and carefully open the cap, top up with
coolant and check that the level is between the MIN
and MAX marks. Also check visually for any fluid
leaks. Contact an Abarth Dealership if the warning
should come on when the engine is started again.
❒if the vehicle is used under demanding conditions
(e.g. towing trailers uphill or fully loaded): slow down
and, if the light stays on, stop the car. Wait for 2 or
3 minutes with the engine running and slightly
accelerated to further favour the coolant circulation.
Then stop the engine. Check correct liquid level as
described above.
IMPORTANT Over demanding routes, it is advisable to
keep the engine on and slightly accelerated for a few
minutes before switching it off.
The display shows the dedicated message.
ç

205
F0U180Abfig. 176
H Maximum allowed weight on second axle (rear)
I Engine type
L Bodywork version code
M Number for spare parts
KNOWING
YOUR VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
TECHNICAL SPECIFICATIONS
IDENTIFICATION DATA
We recommend taking note of the identification codes.
The following identification codes are printed and
shown on the plates:
❒Vehicle identification number (VIN) plate.
❒Chassis marking.
❒Bodywork paint identification plate.
❒Engine marking.
IDENTIFICATION DATA PLATE
fig. 176
The data plate is located on the left side of the boot
floor and it bears the following identification data:
B Type-approval number
C Vehicle type identification code
D Chassis number
E Maximum authorised weight of vehicle fully laden
F Maximum authorised weight of vehicle fully laden
plus trailer.
G Maximum permitted weight on first (front) axle