key ACURA CSX 2006 Service Repair Manual

(#')(#')
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ µ
µ
Engine does not start with the immobilizer
key Immobilizer indicator does not go off
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO YES
NO
22-32522-325
NOTE: Before troubleshooting, check the items listed in
‘‘General Check before Tr
oubleshooting’’ and ‘‘How to
Troubleshoot’’ (see page 22-322).
1. Try to start the engine.
Intermittent failure, the system is OK at this
time. Check status log (see page 22-328).
Go to step 2.
2. Turn the ignition switch to LOCK (0).
3. Turn the ignition switch to ON (II), and check the immobilizer indicator.
Go to step 4.
Go to the immobilizer indicator blinks
troubleshooting (see page 22- 324).
4. Turn the ignition switch to START (III).
Go to step 5.
Go to Starting System and check the starter
motor (see page 4-6).
5. Try to start the engine with the immobilizer key.
Go to step 6.
Go to the PGM-FI System Symptom
Troubleshooting.
6. Wait for a few minutes with the engine running.
Go to the PGM-FI System Symptom
Troubleshooting.
The system is OK at this time. 1. Turn the ignition switch to LOCK (0).
2. Connect the HDS to the data link connector.
3. Turn the ignition switch to ON (II).
4. Enter IMMOBILIZER, then select the IMMOBILIZER
INFORMATION.
5. Do the SYSTEM CHECK with the HDS.
Replace the gauge control module (tach)
(see page 22-277).
Substitute a known-good immobilizer-keyless
control unit, then register it and recheck. If the
symptom goes away, replace the original
immobilizer-keyless control unit (see page 22-332).
Doestheenginestart?
Does t he i nd i cat or come on f or 2 second s, t hen gooff?
Does the starter motor run?Doestheenginestart?Doestheenginestop? Is N-1 OK indicated?
08/08/21 14:37:00 61SNR030_220_0327
ProCarManuals.com
DYNOMITE -2009-

(#')System
Check No. System Check Possible Cause
22-326Immobilizer System
System Check
1. Connect the HDS to the data link connector.
2. Turn the ignition switch to ON (II).
3. Monitor the SYSTEM CHECK in the IMMOBILIZER INFO with the HDS.
4. If the HDS displays NORMAL N-1, the immobilizer system is OK at this time, refer to the STATUS LOG. If the HDS
displays any other messages, check as follows:





















A-1 The key is not
registered This key is not registered in the immobilizer-keyless control unit. Try
to register keys using the HDS.
No communication between the antenna and the immobilizer key
because of interference from metal such as key chains/key rings/
other keys.
Low battery voltage.
A-2 Communication error between the
key and
immobilizer unit Intermittent interruption between transponder and immobilizer-
keyless control unit.
The immobilizer key type is incorrect
non-Acura key.
Key failure (transponder failure)
No communication between the antenna and the immobilizer key
because of interference from metal such as key chains/key rings/
other keys.
Low battery voltage.
A-3 No communication between the key
and immobilizer
unit The ignition switch was turned to ON (II) with a non-immob
ilizer key.
The immobilizer key type is incorrect non-Acura key.
Key failure (transponder failure)
No communication between the antenna and the immobilizer key
because of interference from metal such as key chains/key rings/
other keys.
Low battery voltage.
Immobilizer-keyless control unit failure
B-1 The ECM/PCM is not registered The ECM/PCM was not registered. Try to register the ECM/PCM
using the HDS.
No communication between the ECM/PCM and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the immobilizer-keyless control unit
and the ECM/PCM because of interference.
Open in the IG1 line
B-2 Error of communication
format in ECM/
PCM The ECM/PCM was not registered. Try to register the ECM/PCM
using the HDS.
No communication between the ECM/PCM and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the immobilizer-keyless control unit
and the ECM/PCM because of interference.
08/08/21 14:37:00 61SNR030_220_0328
ProCarManuals.com
DYNOMITE -2009-

System
Check No. System Check Possible Cause
22-327























C-1 The imoes unit is
not registered Imoes unit was not registered.
No communication between the imoes unit and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the imoes unit and the immobilizer-
keyless control unit because of interference.
C-2 Error of communication
format in imoes
unit Imoes unit was not registered.
No communication between the imoes unit and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the imoes unit and the immobilizer-
keyless control unit because of interference.
D-1 S-net line short Harness short from the ECM/PCM to the immobilizer-keyless control unit. (IMOCD (S-net) line short)
No communication between the ECM/PCM and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the immobilizer-keyless unit and the
ECM/PCM because of interference.
Immobilizer-keyless control unit failure
ECM/PCM failure
D-2 No communication between imoes
unit and
immobilizer unit Blown fuse
Harness open from the imoes unit to the immobilizer-keyless control
unit. (IMOCD (S-net) line open)
No communication between the imoes unit and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the imoes unit and the immobilizer-
keyless control unit because of interference.
Immobilizer-keyless control unit failure
Imoes unit failure
D-3 No communication between ECM/PCM
and immobilizer
unit Blown fuse
Harness open from the ECM/PCM to the immobilizer-keyless control
unit.
No communication between the ECM/PCM and the immobilizer-
keyless control unit because of low battery voltage.
No communication between the immobilizer-keyless control unit
and the ECM/PCM because of interference.
Immobilizer-keyless control unit failure
ECM/PCM failure
E-1 Initial registration of immobilizer unit
is not completed The immobilizer-keyless control unit is not registered. Try to register
the immobilizer-keyless control unit using the HDS.
E-2
E-3
E-4
E-5
F-1 Special Mode Turn the ignition switch to ON (II) and to LOCK (0) with the registered key.
F-2
F-3
F-4
F-5
08/08/21 14:37:00 61SNR030_220_0329
ProCarManuals.com
DYNOMITE -2009-

(#')
Status Log No.Detected Item Probable Cause
22-328Immobilizer System
Status Log
If you suspect there is a immobilizer system problem, check the status log in the HDS.
1. Connect the HDS to the data link connector.
2. Turn the ignition switch to ON (II).
3. On the HDS screen, at MAIN MENU, enter IMMOBILIZER, then select IMMOBILIZER SET-UP, select IMMOBILIZER INFORMATION, then select STATUS LOG.
4. Check the STATUS LOG count. Troubleshoot the status with the highest count first. If no counts are listed, the immobilizer system is OK. Continue with normal symptom troubleshooting.






































A-1 KEY CODE MISMATCH
(Code format normal, but code
data is mismatch) The key was not registered
Interference from metal such as key chains
Low battery voltage
A-2 KEY CODE MISMATCH (Code format failure) Ignition switch was turned to ON (II) with another type of immobilizer key or
aftermarket key
Interference from metal such as key chains
Low battery voltage
A-3 KEY CODE MISMATCH (No key code or non-
immobilizer key) Ignition switch was turned to ON (II) with another type of immobilizer key or
aftermarket key
Interference from metal such as key chains
Low battery voltage
Key failure
Immobilizer-keyless control unit failure
B-1 ECM/PCM CODE MISMATCH (Code format normal, but code
data is mismatch) ECM/PCM was not registered correctly
Low battery voltage
Poor or loose terminal connections at the immobilizer-keyless control unit
Communication line electrical noise
B-2 ECM/PCM MISMATCH (Code format failure) ECM/PCM was not registered correctly
Low battery voltage
Poor or loose terminal connections at the immobilizer-keyless control unit
Communication line electrical noise
C-1 IMOES UNIT mismatch (Code format normal, but data is
mismatch) Imoes unit was not registered
The communication was not good between imoes unit and immobilizer unit
by battery voltage low
The communication was not good between imoes unit and immobilizer unit
by influence of some noise
C-2 IMOES UNIT mismatch (Code format failure) Imoes unit was not registered correctly
The communication was not good between imoes unit and immobilizer unit
by battery voltage low
The communication was not good between imoes unit and immobilizer unit
by influence of some noise
D-1 SECURITY-NET LINE PROBLEM IMOCD (S-NET)
(Short to ground) Low battery voltage
Poor or loose terminal connections at the immobilizer-keyless control unit and
the ECM/PCM
Communication line electrical noise
D-2 SECURITY-NET LINE PROBLEM (No communication) Blown fuse
Harness open from imoes unit to immobilizer unit
The communication was not good between imoes unit and immobilizer unit
by battery voltage low
The communication was not good between imoes unit and immobilizer unit
by influence of some noise
Imoes unit failure
Immobilizer unit failure
D-3 SECURITY-NET LINE PROBLEM IMOCD (S-NET)
(Open line or ECM/PCM failure) Open or short in the harness from the ECM/PCM to the immobilizer-keyless
control unit
Low battery voltage
Poor or loose terminal connections at the immobilizer-keyless control unit and
the ECM/PCM
Communication line electrical noise
08/08/21 14:37:01 61SNR030_220_0330
ProCarManuals.com
DYNOMITE -2009-

(#'
)
Add one new key/Keyless transmitter
Add and Delete keys/Keyless transmitters,
Then select Delete or Add keysAll keys are lost
Programming immobilizer-keyless control
unit
22-329
Immobilizer Key Registration
NOTE:
 The HDS is required for registration of the immobilizer keys.
 Programming the immobilizer also programs the keyless transmitter.
 Check for aftermarket electrical equipment that can cause problems with transponder operation.
 The immobilizer-keyless control unit can store up to six immobilizer keys.
1. Have a registered key, a new immobilizer key, and the first password from the iN system.
2. Connect the HDS to the data link connector.
3. Turn the ignition switch to ON (II).
4. Select IMMOBILIZER from the SYSTEM SELECT menu.
5. Select Add and Delete keys, then Add 1 key.
6. Do the registration according to the instructions on the HDS screen.
7. Check if the engine can be started with the newly registered key.
8. When prompted by the HDS, do the keyless transmitter programming.
1. Have all registered keys, all new keys, and the first password from the iN system.
2. Connect the HDS to the data link connector.
3. Turn the ignition switch to ON (II).
4. Select IMMOBILIZER from the SYSTEM SELECT menu.
5. Select Add and Delete Keys, or Delete or Add Multiple Keys.
6. Do the registration according to the instructions on the HDS screen.
7. Check if the engine can be started with all the registered keys. 8. When prompted by the HDS, do the keyless
transmitter programming.
1. Prepare all new keys and have the immobilizer ECM/PCM code.
2. Connect the HDS to the data link connector.
3. Turn the ignition switch to ON (II).
4. Select IMMOBILIZER from the SYSTEM SELECT menu.
5. Select Add and Delete keys, then ALL KEYS LOST.
6. Do the registration according to the instructions on the HDS screen.
7. Check if the engine can with started by all the registered keys.
8. When prompted by the HDS, do the keyless transmitter programming.
1. Have all registered keys and the ECM/PCM code.
2. Connect the HDS to the data link connector.
3. Turn the ignition switch to ON (II).
4. Select IMMOBILIZER from the SYSTEM SELECT menu.
5. Select REPLACE IMMOBILIZER/KEYLESS CONTROL UNIT REPLACE.
6. Do the registration according to the instructions on the HDS screen.
7. Check that the engine can be started with all registered keys.
8. When prompted by the HDS, do the keyless transmitter programming.
08/08/21 14:37:08 61SNR030_220_0331
ProCarManuals.com
DYNOMITE -2009-


(#')
22-330Immobilizer System
Immobilizer-keyless Control Unit Input Test
WHT
BLK
PNK
YEL AB
NOTE: Before testing the immobilizer system, troubleshoot the system using B-CAN System Diagnosis Test Mode A
(see page 22-93) and check the No. 10 (7.5 A) and No. 38 (30 A) fuses in the under-dash fuse/relay box.
1. Remove the driver’s dashboard lower cover (see page 20- 102).
2. Remove the steering column covers (see page 17-9).
3. Disconnect the 7P connector (A) from the immob ilizer-keyless control unit (B).
4. Inspect the connector and socket terminals to be sure they are all making good contact.  If the terminals are bent, loose or corroded, repair them as necessary, and recheck the system.
 IftheterminalslookOK,gotostep5.
Wire side of female terminals
08/08/21 14:37:09 61SNR030_220_0332
ProCarManuals.com
DYNOMITE -2009-

Cavity Wire Test conditionTest: Desired result Possible cause if desired result
is not obtained
Cavity Wire Test condition Test: Desired result Possible cause if desired result
is not obtained
22-331
5. With the connector still disconnected, do these input tests at the following connector.
 If any test indicates a problem, find and correct the cause, then recheck the system.
 If all the input tests prove OK, go to step 6.




1 ORN Under all
conditions Measure the voltage between
immobilizer-keyless control unit
7P connector terminals No. 1
and body ground:
There should be battery voltage. Blown No. 23 (10 A) fuse in
the under-hood fuse/relay
box
An open in the wire
2 YEL Ignition switch ON (II) Measure the voltage to ground:
There should be battery voltage. Blown No. 2 (15 A) fuse in the
under-dash fuse/relay box
An open in the wire
6. Reconnect the connector to the immob ilizer-keyless control unit, and do these input tests at the following
connector.
 If any test indicates a problem, find and correct the cause, then recheck the system.
 If all the input tests prove OK, the immobilizer-keyless control unit must be faulty; replace it.





7 BLK Under all
conditions Measure the voltage to ground:
There should be less than 0.5 V. Poor ground (G101)
An open in the wire
6 PNK Ignition key inserted into the
ignition switch Measure the voltage to ground:
There should be less than 1 V.
Poor ground (G504)
Faulty ignition key switch
An open in the wire
08/08/21 14:37:09 61SNR030_220_0333
ProCarManuals.com
DYNOMITE -2009-


(#' )
22-332Immobilizer System
Immobilizer-keyless Control Unit Replacement
A
B
1. Remove the driver’s dashboard lower cover
(see page 20-102).
2. Remove the steering column covers (see page 17-9).
3. Disconnect the 7P connector (A) from the immobilizer-keyless control unit (B).
4. Remove the two screws and the immobilizer- keyless control unit.
5. Install the immobilizer-keyless control unit in the reverse order of removal.
6. After replacement, register the immobilizer-keyless control unit (see page 22-329), and make sure the
immobilizer system works properly.
08/08/21 14:37:09 61SNR030_220_0334
ProCarManuals.com
DYNOMITE -2009-

Î
Map MatchingObtaining a Navigation DVD
23-94Navigation System
General Troubleshooting Information (cont’d)
Navigation system is unable acquire a
 Move vehicle to another location
 Turn the ignition switch off
 Disconnect the battery for 30
minutes to clear the GPS receiver’s
memory
 Reconnect the battery and follow
the screen prompts proper GPS signal.
If the navigation system finds the satellites properly,
this box clears, and changes to the Disclaimer screen. If
within 10 minutes the system fails to locate a sufficient
number of satellites to locate your position, the
following screen appears.
After 30 minutes with this screen displayed, turn off the
engine, then restart the vehicle. If the Disclaimer screen
appears, the GPS initialization is complete.
NOTE:
 The average acquiring time is less than 10 minutes, but it can take as long as 45 minutes.
 If the system is still unable to acquire a signal, follow the instructions on the screen. If this screen appears
again, go to troubleshooting for the GPS icon is white
or not shown (see page 23-122).
 To bypass the GPS acquire screens, press and hold the Menu, and Zoom out keys at the same time.
Touch the Return button on the screen to exit the
diagnostic mode. This allows you to continue
troubleshooting while in the shop.
This part of the initialization matches the GPS
coordinates with a road on the map screen. To do this
part of the procedure, make sure that the navigation
system displays a map, and drive the vehicle on a
mapped road shown on the map screen. Do not enter a
destination at this time. When the name of the current
road you are driving on, appears at the bottom of the
screen, the entire procedure is complete. Your system
is now ready to use. If the navigation DVD is lost or damaged, or you need a
yearly
updated DVD, you have 2 ways to purchase one.
You can either call 888-291-4675, or order on-line at
www.hondanavi.com.
Both methods require a credit card. The DVD cannot be
ordered through the parts system. The following DVDs
will not work in this navigation system:
 Earlier model navigation DVDs (black, orange, or older vesions with a white label)
 Map software programs manufactured by other companies
 DVD movies, or DVDs containing audio recordings
 Copies of an original Navigation DVD
Update DVDs are available for purchase usually in the
fall of each year. They may contain the following:  Enhanced maps and points of interest (POI) coverage
 Fixes for minor software bugs
 Additional features
NOTE:  Map matching must be done any time the DVD is removed or replaced.
 Always order navigation DVDs on an as-needed basis. During a typical model year, each color DVD may
undergo a half a dozen software only version
upgrades to fix minor issues on some or all models
the DVD supports. This is normal. Usually only the
letter at the end of the version number changes,
while the database (maps and POIs) remain
unchanged.
 Never promise your customers future free updates.
There are no free programs for updating the
navigation DVD. Update DVDs are generally available
for purchase each fall. The on-time DVD order site
provides information when an update for a particular
color DVD is available, damaged discs are not
warrantable.
08/08/21 14:06:25 61SNR030_230_0097
ProCarManuals.com
DYNOMITE -2009-

ItemDefinition
23-110Navigation System
System Description (cont’d)
LCD
Liquid Crystal Display (the navigation screen)
Map matching The received GPS information allows the navigation system to position the vehicle on the map. Map matching
has occurred if the map screen displays the current street name in the bottom-shaded area.
Mic Abbreviation for the microphone used for receiving voice commands. It is located near the map light in the
ceiling. The ANC circuit may also use it to check its tuning.
MID Multi-Information Display
MW Maneuver Window. While on-route to a destination, this window displays information about the next maneuver.
Navi Abbreviation for the Navigation System.
Off-road tracking See bread-crumbs.
Off route Off route This occurs when the user leaves mapped roads. Off road tracking dots (bread-crumbs) are displayed if
the option is enabled in the setup menu. The user can use them to return to a mapped road. The bottom of the
navigation screen displays Not on a digitized road.
Outlying areas These are rural areas that typically have only their main roads mapped. All other roads are shown in light brown
for reference only, since they have not been verified.
Paired Linking your cell phone to the HFL.
PC Card slot PC Card Slot The PC Card (PCMCIA, type II) slot is for factory use only. Make sure that the sliding door is closed at
all times, if opened, an error message is displayed on the screen.
PCM Powertrain Control Module. This unit supplies the navigation system speed signal, also refered to as PCM.
PCMCIA A computer industry defined term referring to the PC Card slot standard.
PIN Personal Identification Number, a random 4 digit number created by the customer to protect personal
information.
POI Point Of Interest. These are the businesses, schools, etc. found under the places option on the main menu.
Polygon Colored areas on the map screen denoting parks, schools, etc. See the Navigation System Manual Driving to
Your Destination for a list of the assigned colors.
QWERTY Keyboard layout resembling the typewriter keys. The keyboard layout can be changed to an alphabetical layout
in the Setup mode.
SCS connector The service check signal 2-pin connector used to put the navigation system into the diagnostic mode.
Security code Code needed to activate the navigation system. You can get the security code from the iN by entering the
navigation unit serial number. You can find the serial number on the diagnostic screens (unit check, Navi ECU),
or on the underside of the navigation unit.
Tuning A continual update of internal navigation system scaling factors. See the individual sensor tuning discussions
under either System Description, or System Diagnosis Mode (see page 23-135).
Unverified Streets These streets have not been verified for turn restrictions, one-way, etc. They appear light brown on the map. You can enter address destinations in these areas, but depending on your Unverified Routing choice in setup, voice
guidance may end at the last verified street closest to your destination.
USB Universal Serial Bus. the USB is used for playing the compressed audio files (MP3, WMA, and AAC) on the
external device through the audio unit.
Verified streets These streets consist of the detailed metropolitan coverage areas, and all other inter-town connection roads.
These roads are shown in black or red on the map. (interstates are red)
VP Vehicle Position. When in map mode, this circular icon shows the vehicle position on the map.
VR Voice Recognition. This allows voice control of many of the navigation functions. The hardware consists of the
microphone, voice control switch (navigation TALK/BACK buttons), and the center speaker. See the overview for
more information.
VSP Vehicle Speed Pulse. This pulse signal coming from the PCM (via the CSS) is used to update the Vehicle position
on the map. These pulses do not indicate direction (forward or backward). When in reverse, the navigation
receives a signal and directs the VP to move backwards on the map.
XM This device receives information from the XM satellites and passes XM audio information to the audio unit. In
addition, traffic information is sent to the navigation unit.
Yaw Sensor This device is located in the navigation system control unit and senses the side-to-side twisting force generated
when the vehicle turns. See a detailed description of how this sensor works in system description.
08/08/21 14:06:29 61SNR030_230_0113
ProCarManuals.com
DYNOMITE -2009-