key ACURA CSX 2006 Service Manual Online


(#'

)
Î
(#'
)
22-20722-207
Ignition Key Switch Test Ignition Key Light Test
A
A
1. Remove the steering column upper and lower
covers (see page 17-9).
2. Disconnect the 6P connector (A) from the ignition key switch.
3. Check for continuity between terminals No. 1 and No. 2.
 There should be continuity with the key in the ignition switch.
 There should be no continuity with the key removed.
4. If the continuity is not as specified, replace the steering lock assembly. 1. Remove the steering column upper and lower
covers (see page 17-9).
2. Disconnect the 6P connector (A) from the ignition key switch.
3. The LED should come on when power is connected to terminal No. 6 and ground is connected to
terminal No. 5.
4. If the LED does not come on, replace the steering lock assembly.
08/08/21 14:27:55 61SNR030_220_0209
ProCarManuals.com
DYNOMITE -2009-

(#')
22-212Power Windows
Circuit Diagram
G21
N9
5
2
3
6
4
1
11
(LED) *3
(LED)
*1 *2 (LED)
UNDER-DASH FUSE/RELAY BOX
BLU
No. 4 (P/W) (40 A)
UNDER-HOOD FUSE/RELAY BOX
No. 1 (BAT) (100 A)
BATTERY
CONTROL UNITDOWN
UP
DRIVER’S
YEL GRN PUR
PNKORN
UP DOWN SVCC PLSA PLSB
6
5
16
9
10 4
POWER WINDOW MASTER SWITCH No. 26
(20 A)
WHT
PULSER
BLK
G503 7
SGND
BRN POWER
WINDOW
RELAY
DOWN
(AUTO)
UP
(AUTO) MICU
(Key-off
timer)
DR
LIGHT
(LED) K2
DRIVER’S POWER WINDOW MOTOR 32
4 1
08/08/21 14:28:39 61SNR030_220_0214
ProCarManuals.com
DYNOMITE -2009-

Î(#'
)
Except TYPE S model
22-244Gauges
Circuit Diagram - Gauge Control Module (Tach)
UART
WHT
IG1 HOT in ON (II) and START (III)
UNDER-HOOD FUSE/RELAY BOX
5V



MAIN CIRCUIT
MAIN CIRCUIT
MICU
  LT GRN
20
21
PNK
124
CAN L
CAN H 

 CHIME
BRN
WHT BRN
RED 19
1
WHT No. 2 (IG) (50 A)
GAUGE CONTROL MODULE (TACH) 18 17 TACHOMETER ORN
IG1
BAT
BLU
WHT
No. 23 (10 A)
BATTERY
IGNITION SWITCH
No. 1 (BAT) (100 A)
(7.5 A) No. 10UNDER-DASH
FUSE/RELAY
BOX
GAUGE CONTROL
MODULE (SPEEDO)
DRIVE
CIRCUIT DIMMING
CIRCUIT
PARKING
BRAKE
REMINDER
SEAT
BELT
REMINDER
KEY-IN
REMINDER
F-CAN
TRANSCEIVER B-CAN
TRANSCEIVER
IMMOBILIZER-
KEYLESS
CONTROL UNIT GAUGE
CONTROL
MODULE
(SPEEDO) 10 V
STABILIZING
CIRCUIT
HIGH BEAM
INDICATOR
(LED)
LIGHTS-ON
REMINDER
CLIMATE CONTROL
UNIT
HANDSFREELINK
CONTROL UNIT*3 IMMOBILIZER
INDICATOR
(LED)
ON/OFF
5V
5V
CONTROL
CIRCUIT
H1
D4 G2D2
Q1 P5 P10 Q9
A
ECM/PCM
ABS MODULATOR-
CONTROL UNIT*1
VSA MODULATOR-
CONTROL UNIT*2
YAW RATE-LATERAL
ACCELERATION SENSOR*2
EPS CONTROL UNIT
TPMS CONTROL UNIT*2
DATA LINK CONNECTOR
SRS UNIT







 MICU
08/08/21 14:35:12 61SNR030_220_0246
ProCarManuals.com
DYNOMITE -2009-

Î(#'
)
TYPE S model
22-250Gauges
Circuit Diagram - Gauge Control Module (Tach) (cont’d)
UART
WHT
IG1 HOT in ON (II) and START (III)
UNDER-HOOD FUSE/RELAY BOX









 ECM
VSA MODULATOR-
CONTROL UNIT
YAW RATE-LATERAL
ACCELERATION SENSOR
EPS CONTROL UNIT
TPMS CONTROL UNIT*1
DATA LINK CONNECTOR
SRS UNIT MAIN CIRCUIT
MAIN CIRCUIT
MICU
  GRY
2
21
PNK
124
CAN L
CAN H 

 CHIME
BRN
WHT BRN
RED 19
1
WHT No. 2 (IG) (50 A)
GAUGE CONTROL MODULE (TACH) 18 17 TACHOMETER ORN
IG1
BAT
BLU
WHT
No. 23 (10 A)
BATTERY
IGNITION SWITCH
No. 1 (BAT) (100 A)
(7.5 A) No. 10UNDER-DASH
FUSE/RELAY
BOX
GAUGE CONTROL
MODULE (SPEEDO)
DRIVE
CIRCUIT DIMMING
CIRCUIT
PARKING
BRAKE
REMINDER
SEAT
BELT
REMINDER
KEY-IN
REMINDER
F-CAN
TRANSCEIVER B-CAN
TRANSCEIVER
IMMOBILIZER-
KEYLESS
CONTROL UNIT GAUGE
CONTROL
MODULE
(SPEEDO) 10 V
STABILIZING
CIRCUIT
HIGH BEAM
INDICATOR
(LED)
LIGHTS-ON
REMINDER
CLIMATE CONTROL
UNIT
HANDSFREELINK
CONTROL UNIT*2 IMMOBILIZER
INDICATOR
(LED)
H1
D4 G2D2
Q1 P5 P10 Q9
A DRIVER DRIVERMAIN CIRCUIT
MICU
08/08/21 14:35:15 61SNR030_220_0252
ProCarManuals.com
DYNOMITE -2009-

µµµ
(#'

)
Description
Outside Air Temperature Indicator Logic Update to the outside air temperature
indicator while driving
Troubleshooting
22-279
Outside Air Temperature Indicator Calibration
The outside temperature sensor is located behind the
center of the front bumper. The gauge control module
(tach) uses measurements from this sensor to display
the outside air temperature.
Because of the location of the sensor, it may be affected
by heat reflection from the road, engine and radiator
heat or hot exhaust from surrounding traffic.
These conditions can heat soak the outside air
temperature sensor and cause inaccurate readings.
Logic has been written into the gauge control module
(tach) to help prevent abnormal or fluctuating outside
air temperature indicator readings.
Initial outside air temperature indication after the
ignition switch is turned to ON (II).
 If the engine coolant temperature is 60 °C (140 °F) or higher when the ignition switch is turned to ON (II),
the outside air temperature indicated the last time the
key was turned off will be displayed regardless of the
current temperature measured by the outside air
temperature sensor.
 If the engine coolant temperature is 59 °C (139 °F) or lower when the ignition switch is turned to ON (II), the
current temperature measured by the outside air
temperature sensor will be indicated. If the temperature measured by the outside air
temperature sensor is greater than the temperature on
the outside air temperature indicator, the outside air
temperature indicator will increase by 1 °C (1.8 °F) per
minute after the vehicle speed is greater than 30 km/h
(19 mph) for more than 1 minute and 30 seconds. It will
continue to increase until the current outside air
temperature is indicated. So, the first change to the
outside air temperature indicator is 1 minute and
30 seconds after the vehicle speed is greater than
30 km/h (19 mph). If the vehicle speed drops below
30 km/h (19 mph), the indicator will not update again
until the vehicle speed is increased to 30 km/h (19 mph)
or more for more than 1 minute and 30 seconds again.
If the outside air temperature is less than the indicated
temperature, the temperature will decrease 1 °C every
2 seconds (1 °F
every 1.1 seconds) until the current
outside air temperature is indicated regardless of
vehicle speed.
If the indicator displays ‘‘ ’’ for more than 2
seconds after selecting the outside air temperature
display mode, check the outside air temperature sensor
(see page 21-68), or gauge control module self-
diagnosis (see page 22-241).
(cont’d)
08/08/21 14:36:00 61SNR030_220_0281
ProCarManuals.com
DYNOMITE -2009-

Î
Î(#'

)
22-281
Reminder Systems
Component Location Index
GAUGE CONTROL MODULE (TACH)
MICU COMBINATION LIGHT SWITCH
IGNITION KEY SWITCH PARKING BRAKE SWITCH SRS UNIT
DRIVER’S DOOR SWITCH FRONT SEAT BELT
BUCKLE SWITCHES
Input Test, page 22-271
Input Test, page 22-284 Test/Replacement, page 22-166
Test, page 22-72 Test, page 19-11
08/08/21 14:36:01 61SNR030_220_0283
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
µµ
µ
22-282 Reminder Systems
Circuit Diagram


MICU







 ORN
(10 A) No. 23
BLK1 2
SRS UNIT
G602
B11
A12
A11 YEL
WHT REDRED
WHT
ORN28
LT GRN BLK16
G504
INDICATOR DRIVE CIRCUIT
MICU
  ECM/PCM MAIN CIRCUIT
21
PNK
124
CAN L
CAN H


 CHIME
WHT
BRN
RED 19
1
WHT No. 2 (IG) (50 A)
GAUGE CONTROL MODULE (TACH) 18
17
IG1
BAT
BLU
WHT
UNDER-HOOD FUSE/RELAY BOX
BATTERY IGNITION SWITCH
No. 1 (BAT) (100 A)
(7.5 A) No. 10UNDER-DASH
FUSE/RELAY
BOX
DRIVE
CIRCUIT
PARKING
BRAKE
REMINDER
SEAT
BELT
REMINDER
KEY-IN
REMINDER
F-CAN
TRANSCEIVER B-CAN
TRANSCEIVERLIGHTS-ON
INDICATOR
(LED)
IG1 HOT in ON (II)
and START (III)
ABS MODULATOR-
CONTROL UNIT*1 LIGHTS-ON INDICATOR
DIMMING CIRCUIT
PARKING
BRAKE
SWITCH
(Closed:
Lever pulled)
DRIVER’S
SEAT BELT
BUCKLE
SWITCH
(Closed:
unbuckled) SEAT BELT
REMINDER
INDICATOR
(LED)
BRAKE
SYSTEM
INDICATOR
(LED)COMPULSORY
TURNING-ON
CIRCUIT
LIGHTS-ON
REMINDER
CLIMATE
CONTROL
UNIT
IMMOBILIZER-
KEYLESS
CONTROL UNIT
HANDSFREELINK
CONTROL UNIT*4
H1
D4 D2
Q1 Q9
G2 :CANline
1
VSA MODULATOR-
CONTROL UNIT*2
YAW RATE-LATERAL
ACCELERATION SENSOR*2
DATA LINK CONNECTOR
EPS CONTROL UNIT
TPMS CONTROL UNIT*3 10 V
STABILIZING
CIRCUIT
*1: ’06 07 Touring and Premium models
*2: ’07 TYPE S and ’08 09 models
*3: ’08 09 models
*4: ’09 model with navigation system
MICU
A
B
08/08/21 14:36:02 61SNR030_220_0284
ProCarManuals.com
DYNOMITE -2009-

Î
22-283
R16
PNK
Q6
PNK
PNK
B-CAN PNK
R6
G504 BLK
2 1
PNK
GRN E37 MICU
UNDER-DASH FUSE/RELAY BOX
9 S1
ORN S5
S11S13
BLK
PNK
GRY
12
(
()
1011
)
OFF
COMBINATION LIGHT SWITCH DRIVER’S
DOOR SWITCH
(Closed :
Door open)
IGNITION
KEY
SWITCH
(Closed :
Key inserted)IMMOBILIZER-
KEYLESS
CONTROL UNIT
GAUGE CONTROL
MODULE (TACH)




MICU
CLIMATE CONTROL
UNIT
IMMOBILIZER-
KEYLESS
CONTROL UNIT
HANDSFREELINK
CONTROL UNIT*
1 : CAN line
*: ’09 model with navigation system
A
08/08/21 14:36:02 61SNR030_220_0285
ProCarManuals.com
DYNOMITE -2009-

Cavity WireTest condition Test: Desired resultPossible cause if desired result is not
obtained
22-285
5. Reconnect the connector to the under-dash fuse/relay box, and do these input tests at the following connectors.
 If any test indicates a problem, find and correct the cause, then recheck the system.
 If all the input tests prove OK, the MICU must be faulty; replace the under-dash fuse/relay box.





















E37 GRN Driver’s door open Measure the voltage to ground:
There should be less than 0.5 V.Faulty driver’s door switch
An open in the wire
Driver’s door closed Measure the voltage to ground: There should be more than 5 V. Faulty driver’s door switch
A short to ground in the wire
R6 PNK Ignition key inserted into the ignition switch Measure the voltage to ground:
There should be less than 0.5 V. Poor ground (G504)
Faulty ignition key switch
An open in the wire
Ignition switch OFF and ignition
key removed from the ignition
switch Measure the voltage to ground:
There should be more than 5 V.
Faulty ignition key switch
A short to ground in the wire
S1 ·
S5 ORN
·
BLK Combination light switch OFF Measure the voltage between S1
and S5 terminals:
There should be less than 0.5 V. Faulty combination light switch
An open in the wire
Combination light switch in any
other position than OFF Measure the voltage between S1
and S5 terminals:
There should be more than 5 V. Faulty combination light switch
A short to ground in the wire
S11 ·
S5 PNK
·
BLK Combination light switch
(Headlight position) ON
Measure the voltage between S11
and S5 terminals:
There should be less than 0.5 V. Faulty combination light switch
An open in the wire
Combination light switch OFF Measure the voltage between S11 and S5 terminals:
There should be more than 5 V. Faulty combination light switch
A short to ground in the wire
S13 ·
S5 GRY
·
BLK Combination light switch
(SMALL position) ON
Measure the voltage between S13
and S5 terminals:
There should be less than 0.5 V. Faulty combination light switch
An open in the wire
Combination light switch OFF Measure the voltage between S13 and S5 terminals:
There should be more than 5 V. Faulty combination light switch
A short to ground in the wire
08/08/21 14:36:03 61SNR030_220_0287
ProCarManuals.com
DYNOMITE -2009-

Î
Î(#')
22-314Immobilizer System
Component Location Index
IMMOBILIZER INDICATOR
IMMOBILIZER-KEYLESS CONTROL UNIT (With built-in receiver)
IMOES UNIT
(Built into the MICU)
TRANSPONDER
(Combined with the
keyless transmitter)
IGNITION KEY IGNITION KEY
(Including transponder)
ECM/PCM
Symptom Troubleshooting Information, page 22-321
System Check, page 22-326
Registration, page 22-329
Input Test, page 22-330
Replacement, page 22-332
Transmitter Test, page 22-142 Replacement,
page 11-228
Substitute known- good for testing,
page 11-7
08/08/21 14:36:57 61SNR030_220_0316
ProCarManuals.com
DYNOMITE -2009-