key ACURA CSX 2006 Service Repair Manual

Icon
Colors Description
23-298Navigation System
System Diagnostic Mode (cont’d)
The System Links function runs automatically and
displays a flashing message at the bottom of the
screen reminding you to have the engine running
for the test. The diagnostic tests the following:
 Most of the wires connecting the navigation components shown in the block diagram.
 The results from the various components shown in the block diagram.
 The microphone is tested by listening to the bong sound produced by the navigation unit from the
speakers when the diagnostic is started. This
requires that the audio system be operating
normally.
When the diagnostic finishes, the icons turn
different colors based on their test status. The color
definitions are shown below and can also be seen
by selecting Help on the System Links screen.
The indication on the screen may not change until
you exit and reenter the Self-Diagnosis mode. In
some cases, you may have to restart the engine for
the indication to change. After you repair the
affected component or harness, repeat this
diagnostic. Explanation of each icon
Each icon color is explained in the table below.
Green The system ran a diagnosis and the results are OK.
Red Errors that require replacement of hardware or harness. Examples
are connection error or memory
diagnosis errors. Troubleshooting
for DTCs.
Yellow Errors that doesn’t require hardware replacement, such as an
open display cover, an incorrect
DVD, leaving the vehicle in
ACCESSORY (I), or because of a
missing accessory, like the
rearview camera.
White The diagnosis is running. The screen functions are locked out
while the diagnosis is runs.
Gray The system cannot automatically check this function. You have to
select the diagnosis item and
manually do additional testing,
like checking the navigation
buttons in the Hard Key test.
When you complete the Hard Key
test and return to the System
Links menu, the gray icon turns
green.
NOTE: By selecting the HELP icon, you can see a
description for each color.
08/08/21 14:16:38 61SNR030_230_0301
ProCarManuals.com
DYNOMITE -2009-

••••••
•••
••• •••
••• ••• ••• •••
•••
••• ••• ••• •••
Icon Icon Color
GREEN RED YELLOW WHITE GRAY
23-300Navigation System
System Diagnostic Mode (cont’d)
Mic
The microphone
detects the
sound ‘‘Pi-Pi-
Pon’’ at the
system link
menu. The microphone
could not detects
the sound ‘‘Pi-Pi-
Pon’’ at the
system link
menu. Executing (Not
completed)
ECU Info. Both V-RAM or D-RAM is OK,
and all Program
Flash, Serial No.,
Model is
available, and
the DVD lid is
closed.Either the
V-RAM or D-
RAM is NG, or
any of the
Program Flash,
Serial No.,
Model is
unavailable.DVD lid is
opened
Executing (Not
completed)
Hard Key All buttons are pressed and are
detected under
Hard key menu.All buttons are
not pressed or
pressed but not
detected under
Hard key menu,
or exit from Hard
key menu
without the
button not
detected. Until changing to
Hard key menu.
Error History Hard Error or
Soft Error is
detected under
Error History
menu. Executing (Not
completed)
Hard Error or
Soft Error is not
detected under
Error History
menu.
DVD DVD mechanism
is normal and
the proper DVD
is installed. Improper DVD is
installed, or DVD
is not installed,
or can not
identify software
version from the
DVD or internal
mechanism
failure.Executing (Not
completed)
Yaw Sensor Result of the Yaw Sensor
diagnosis menu
is OK.Result of the
Yaw Sensor
diagnosis menu
is NG.Result of the
Zero Point
Output under the
Yaw Sensor
diagnosis menu
is NO CHECK.Executing (Not
completed)
Car Status Check these
systems
manually.
08/08/21 14:16:39 61SNR030_230_0303
ProCarManuals.com
DYNOMITE -2009-

µ
Î
Î
Factory diagnostic screen In Line DiagDetailed Information & Settings
23-301
In Line Diag
123
456
789
0 Return
Navi ECU
Display XXXXCorrect PIN
GPS Antenna
RR Camera RadioXM
HFL A/C
Exit Diag
Start Diag
BACK
Delete Done
KA
Select Diagnosis Items
Self- Diagnosis Mode
Detail Information & Setting
(Navi will check internal function. connections, etc.
Perform this test with vehicle stopped and engine running.)
(Individual Diagnostic screens to confirma specific diagnostic screen.)
NOTE: If the vehicle left the factory in the factory
diagnostic mode, or if the navigation unit is replaced
you will see this screen every time you turn on the
ignition.
When a navigation unit is powered up for the first time
at the factory or after replacement with a new or
remanufactured navigation unit, the factory diagnosis
screen (In Line Diag) appears. Normally the factory
does the steps necessary to verify proper operation and
terminate the factory diagnostic.
Until the proper confirmation sequence is done, the
screen appears every time the vehicle is started.
Follow the steps below to prevent the screen from
showingupinthefuture:
 Press and hold the buttons (MENU, MAP/GUIDE, and CANCEL) for about 3 seconds. The Select Diagnosis
items screen appears.
 Press and hold the MAP/GUIDE button for 5 10 seconds. A screen with a Complete button,
appears.
 Press complete, then Return, and then shut the key off for 5 seconds. Do not disconnect the battery
during this period as the unit is saving the setting to
the SRAM memory. The In Line Diag should not
appear again.
 Restart the vehicle, and confirm normal operation by completing the TQI of the Navigation System Service
Bulletin. These section allows you to run a specific diagnostic
and allows additional setting choices for some screens
that are not shown when selecting an icon from the
System Links screen.
When you select the menu item Detail Information &
Setting menu, the main diagnosis menu is displayed.
(cont’d)
08/08/21 14:16:39 61SNR030_230_0304
ProCarManuals.com
DYNOMITE -2009-

´´
´µ
Î
Î Î

´
Black Raster
Touch Panel Check 1Touch Panel Calibration
23-303
Black RasterReturn
Return
Return
SetX:0 Y:0
X:227 Y:111
X:479 Y:2331
2
3 4
5
Please press the center of’’ ’’button.
This diagnostic screen checks for pixels that may be
stuck on. The entire display must be black. If pixels are
stuck on, replace the navigation unit.
The panel touch sensing system consists of a touch
sensitive resistive membrane covering the display.
Contrary to other systems using infrared beams, the
screen has to be physically touched to make it work.
The display has the capability of 479 touch locations
(left to right), and 233 touch locations (top to bottom).
The upper left hand corner is position (0, 0) and the
lower right hand corner is (479, 233) as displayed.
Touching anywhere on the screen displays the
coordinate of the location, and a icon appears where
you touched the screen. If any area of the screen either
doesn’t respond, or responds at some other location
when touched, then replace the navigation unit.
NOTE: Unlike earlier screens that used infrared sensors,
direct sunlight does not affect this test. The display screen uses a touch sensitive membrane.
This means that every location of the entire surface of
the display is touch sensitive. This diagnostic allows
alignment of these touch locations with the location of
the buttons images on the screen.
Normally this should n
ever need adjustment, and is
used only to adjust the touch locations for parallax (the
touch locations appear different when viewed at an
angle). However, if an adjustment is necessary, follow
this procedure:
 The screen consists of the button icons. Touch the center of the five buttons on order 1 5.
 To store any change you make, touch the Set button.
 Use the Return key to exit the diagnostic.
(cont’d)
08/08/21 14:16:40 61SNR030_230_0306
ProCarManuals.com
DYNOMITE -2009-

Î
Î

Î

Unit Check (Quick Check)Display
Radio
23-305
ReturnReturn
ReturnSelect Check Units Display Radio Hard Key
Yaw Sensor DVD
GPS
ECU Info.
Rear Camera
PC Card Info Aircon
HFL
XM Display
OK
OK
Connection
Version
040423
Radio OK
Connection
OK
0.2dBuV
Electric Field Intensity
7150
CD Mech. Version
Some of the tests and screens that are displayed under
the Unit Check are different from the more detailed
checks listed in other areas of this service manual.
To start the test, select the item you want to check.
Display
Radio
GPS
ECUInfo.
 Rear Camera
 PC Card Info.
 Hard Key
 Yaw Sensor
DVD
 Aircon
HFL
XM This performs additional checks on the communication
bus between the navi CPU and the navigation display.
In addition, this test checks the internal electronic
functions
If the connection is NG, replace the navigation unit.
 Connection verifies internal communications.
 Version represents the software version for the display.
This diagnostic screen checks the internals of the radio
(AM and FM) and CD player. If NG, replace the
navigation unit.
(cont’d)
08/08/21 14:16:41 61SNR030_230_0308
ProCarManuals.com
DYNOMITE -2009-

´µ ´µ
Î
Î Î
Î
Î
´
µ
´
µ
´µ
Hard Key
Yaw Sensor DVD
Aircon
HFL
23-308Navigation System
System Diagnostic Mode (cont’d)
Hard KeyReturn
Return
ZOOM OUT ZOOM IN
CANCEL SET UP MAP
MENU INFO
MODE CH
CH
VOL
VOL
FF
REW
RPT RDM
SEEK UP SCAN
AUDIO
CD/AUX
AM/FMSKIP
SKIP
SEEK DOWN Keep Pushing to Return.
Yaw Sensor
Zero Point Output OK OK
Output Value x.xxxV
Current Offset x.xxxV
Temperature in ECU xx°C
Return
Return
ReturnDVD
Error Detail -
Version 20050404
Maker ID 0x01
Navi Platform 0x01
Connection OK Aircon
HFL
Connection OK
This diagnostic screen checks the status of each of the
hard buttons surrounding the navigation display. When
you press each hard button, the corresponding item on
the screen should flash blue. Touch the return key, or
press and hold the joystick to exit.
NOTE: It is normal for the VOL ( , ) CH ( , ) and
MODEbuttontobeinactive.
This screen gives a quick test of the yaw sensor
functionality based on the two voltages Sensor and
Offset. For more information see the Yaw Rate
Diagnostic. This diagnostic tests the navigation DVD reader.
This diagnostic tests the climate bus connection (AC-SI
and AC-SO) between the navigation unit and climate
control unit. Make sure the engine is running for this
test.
 This checks the 4 wire communication bus between the HFL and the navigation.
 When connection is shown with NG, check the connection between the navigation unit and the
HandsFreeLink control unit.
08/08/21 14:16:42 61SNR030_230_0311
ProCarManuals.com
DYNOMITE -2009-

(#'#
)

µ
µ
µ
µ
YES
NO
YES
NO
Navigation display buttons do not work or
respond properly
23-34023-340Navigation System
Symptom Troubleshooting (cont’d)
5. Turn the ignition switch to LOCK (0), then turn to
ON (II), and observe the navigation picture.
Check for sources of electrical noise, such as
poor battery connection, alternator, defective
battery, aftermarket accessories or cell phone, and
poor pin fits at the navigation unit.
Replace the navigation unit (see page 23-355). NOTE:
 Check the vehicle battery condition first.
 Always make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Always check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the navigation system anti-theft codes.
1. Turn the ignition switch to ON (II).
2. Go into the Detail Information & Settings select Unit Check, and use Hard Key test under Unit Check
(see page 23-305).
The system is OK at this time.
Replace the navigation unit (see page 23-355).
Di d t he i mage i mpr ov e?
Does t he nav i gat i on uni t but t ons w or k pr oper l y ?
08/08/21 14:17:50 61SNR030_230_0343
ProCarManuals.com
DYNOMITE -2009-

(#'#
)(#'#
)

µ
µ
µ
µ
µ
µ µ
µ
µ
µ
Navigation display stays on with ignition
switch in LOCK (0) Navigation cannot control audio system
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
23-34923-349
NOTE:
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, get the navigation system anti-theft code, then write down the audio presets.
 After troubleshooting, re-enter the anti-theft code, and re-initialize the navigation system, then enter the
audio presets.
 Check for aftermarket accessories that use the same power circuit. A feedback can cause this problem.
1. Remove the key from the ignition.
Go to step 2.
The system is OK at this time.
2. The vehicle may have been used as a demonstration vehicle at an event like an auto
show. In these events, power is often jumpered to
the navigation system so that the ignition key is not
needed in the vehicle. At the end of the show, the
jumper wire may not have been removed. Check
the navigation unit connector A (24P) for a non-
factory jumper wire in series with the factory cable.
Remove the jumper wire, and re-test. Return
the jumper wire to Tech Line.
Go to step 3.
3. Check if the audio unit works.
Troubleshoot the ACC circuit for a short to
power with another circuit.
Replace the navigation unit (see page 23-355). NOTE:
 Check the vehicle battery condition first.
 Verify that the correct navigation unit is installed for this model. Go into the Diagnostic mode and use
Version (see page 23-316).
 Check for connectors for poor connections loose terminals.
 Before troubleshooting, make sure you have anti- theft codes for the navigation system.
 After troubleshooting, enter the anti-theft codes for the navigation system.
 Make sure that the correct navigation DVD color and version are installed.
 Inspect the navigation DVD for dirt or damage.
 Check any official Honda service website for more service information about the navigation system.
1. Make sure the anti-theft code for the navigation system is entered.
2. Go into the Diagnostic Menu, and use the Navi System Link test (see page 23-297).
Do the troubleshooting for the voice
guidance cannot be heard (see page 23-341).
Go to step 3.
3. Substitute a known-good navigation unit (see page 23-355), and recheck.
Replace the navigation unit (see page 23-355).
Do the audio system troubleshooting.
Does t he nav i gat i on scr een st ay on?
Is t her e a j umper w i r e?Does the audio unit work with the ignition switchoff? Is the Radio icon red?
Can t he nav i gat i on cont r ol aud i o?
08/08/21 14:17:52 61SNR030_230_0352
ProCarManuals.com
DYNOMITE -2009-

(#'#
)
µ
µ
µ
µ µ
µ
µ
µ
µ
µ
Navigation system will not accept security
code
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
23-353
NOTE:
 Check the vehicle battery condition first.
 The system will not operate without the 4-digit security (anti-theft) code. Follow the this procedure.
(After 10 consecutive tries, you must cycle the key to
continue trying)
 The Navigation System Diagnosis and Core Return From is available online, under Job aids, and can be
printed out for recording this information. This
information will help the reman facility determine
what caused the failure.
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the anti- theft codes for the navigation system.
 Verify that the correct navigation unit is installed for this model. Go into the Diagnostic mode, and use
Version (see page 23-316).
 Make sure that the correct navigation DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
1. Go into the System diagnosis menu (see page 23-297), select Unit check, and then ECU info. A
brief diagnostic runs for 20 seconds, and the serial
number is displayed.
Go to step 4.
Go to step 2.
2. Remove the navigation unit (see page 23-355).
3. Check the serial number on the label on the underside of the navigation unit.
Go to step 4.
Replace the navigation unit (see page 23-355). 4. Using the serial number, look up the navigation
security code in the Interactive Network. (click:
Service, Vehicle Information, Anti-Theft code
Inquiry, and then select Navigation from the
Product dropdown box). Enter the serial number.
Go to step 5.
Call the Warranty Department to obtain the
code (the telephone number is in the PDI service
bulletin).Thengotostep5.
5. Check that the obtained code works to bypass the code screen in the navigation system.
The system is OK at this time Return the
vehicle to the client, and give them the anti-theft
code.
Go to step 6.
6. Try entering four zeros (0000) in place for the code.
Replace the navigation unit, and enter
Security code is 0000 in the problem description
field of the core return form.
Replace the navigation unit, and enter Won’t
take security code (as proof, enclose the sticker that
contains the Serial number and the Code) in the
problem description field of the core return form.
Is t he ser i al number d i spl ay ed ?
Is the serial number conf irmed on the underside oft he nav i gat i on uni t ? Is a 4-digit code displayed on the screen?
Doesthecodework?Do t he f our zer os w or k t o by pass t he cod e scr een?
08/08/21 14:17:53 61SNR030_230_0356
ProCarManuals.com
DYNOMITE -2009-

Pairing TroubleshootingPairing Checks
23-364HandsFreeLink System
General Troubleshooting Information (cont’d)
Many pairing issues are resolved by altering the client’s
phone settings.
Bluetooth feature settings must be turned on. Phone
manufacturers set the default to disable Bluetooth
features to conserve battery life. Cell phones may
provide procedures to Temporary Power On Bluetooth,
or Power On Bluetooth. Turn the Bluetooth feature on,
pair the phone to the vehicle, and confirm the phone is
linked. Do this by turning the phone off and back on.
Make or receive a call to confirm that the cell phone is
successfully paired.
When the phone’s Bluetooth feature is on, other
handsfree accessories such as earpieces or headsets
may automatically reconnect to the phone when you
turn on the accessory or move it within range of the cell
phone. This results in the phone not connecting to the
HFL system when the client’s enters the vehicle. You
must unlink the hands-free accessory from the phone
before the HFL system can reconnect.
Some phones have an Auto Answer setting that
functions with a headset. This setting must be turned
off or the HFL system cannot accept any incoming calls.
When this setting is on, it blocks the HFL system from
answering the call, and the call goes to voice mail. This
can cause the client to think that the cell phone is not
paired properly.
If the HFL system has six phones paired, it will not tell
you that it has reached its maximum, and will not allow
you to pair a new phone. To check how many phones
are paired, press and release the HFL TALK button.
After the beep, say ‘‘Phone setup list.’’ The HFL system
lists every assigned
phone name paired with it, then
finishes by saying ‘‘The entire list has been read.
Returning to the main menu.’’ Count the number of
phones listed. If there are six, you must delete one
phone before adding a new one. For more information about pairing, refer to the cell
phone owner’s manual, or go to handsfreelink.com.
1. Is the cell phone compatible with the HFL?
2. Is the Bluetooth feature turned on?
3. Is the client using the HFL buttons, not the navigation buttons, when pairing?
4. Is the cell phone battery fully charged, and is there good signal strength when pairing?
5. Do a soft reset on the cell phone.
6. If the client is trying to pair a Blackberry
or Palm
Treo device, make sure the client uses the shift
key when entering the pass code. If the shift key is
not pressed, the client may be entering letters. The
HFL does not recognize letters.TM
08/08/21 14:18:37 61SNR030_230_0367
ProCarManuals.com
DYNOMITE -2009-