ABS ACURA CSX 2006 Service Repair Manual


(#'

 ) Special Tools Required
Front
19-173
Wheel Speed Sensor Replacement
A
B
C9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
Guide pin tool 07AAG-SVBA100
1. Turn the ignition switch to LOCK (0).
2. Release the clamp (A), then disconnect the wheel speed sensor connector (B).
3. Remove the clips, the bolt, and the wheel speed sensor (C).
4. Install the wheel speed sensor in the reverse order of removal, and note these items:  Install the sensor carefully to avoid twisting the wires.
 If the wheel speed sensor comes in contact with the wheel bearing, it is faulty, investigate the cause beforereplacing the sensor.
5. Start the engine, and make sure the ABS and the VSA indicators go off.
6. Test-drive the vehicle, and make sure the ABS and the VSA indicators do not come on.
(cont’d)
08/08/21 15:06:47 61SNR030_190_0173
ProCarManuals.com
DYNOMITE -2009-

Î
ÎÎ
19-175
A
B
A
07AAG-SVBA100 B
07AAG-SVBA100
A
4. Apply multi-purpose grease to the wheel speedsensor O-ring (A) and the sensor hole in the knuckle
(B).
5. Insert the guide pin tool (A) into the wheel speed sensor bolt hole until the shoulder of the tool
contacts the wheel speed sensor bracket.
NOTE: To prevent O-ring damage, the wheel speed
sensor must be installed with the guide pin tool. 6. Insert the wheel speed sensor (A) and the guide pin
tool (B) into the bolt hole on the knuckle.
NOTE: To ensure proper alignment when pushing
the wheel speed sensor into the knuckle housing,
do not hold the sensor bracket during installation,
hold the sensor wire.
7. Gently push and pull the wheel speed sensor in and out to make sure the O-ring is sliding properly in its
housing. While you are doing this, make sure the
sensor doesn’t come out of the knuckle assembly. If
the sliding effort is too high, remove the wheel
speed sensor, inspect the O-ring for damage, and
start the installation process again.
8. Remove the guide pin tool, then install the bolt, and tighten it to specified torque.
9. Clean the mating surfaces between the brake disc and the inside of the wheel, then install the front
wheel.
10. Start the engine, and make sure the ABS and the VSA indicators go off.
11. Test-drive the vehicle, and make sure the ABS and the VSA indicators do not come on.
08/08/21 15:06:48 61SNR030_190_0175
ProCarManuals.com
DYNOMITE -2009-



(#' )

S

pecial Tools Required
Driver’s side Passenger’s sideFront Door Sill Area
20-66Interior Trim
Trim Removal/Installation - Door Areas
A
B C
D
E
F
G G
A B A
B
G
G
Fastener Locations
:Clip,1
F : Clip, 4
G
(White)
(Orange)
E Fa
stener Locations
: Clip, 1
F : Clip, 4
G
(White)
(Orange)
A
B
C D E
F
G B
A
A
BG
G
G
E
AB
A
A
KTC trim tool set SOJATP2014
NOTE:
Put on gloves to protect your hands.
 Take care not to bend or scratch the trim and panels.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Driver’s side: Remove the footrest (see step 3 on page 20-89).
2. Driver’s side: Remove the front side cap from the front door sill trim, and remove the trunk lid/fuel fill
door opener lock cylinder and the screw (see page
20-184).
3. Detach the hooks (A) and the tabs (B) from the kick panel (C) and the B-pillar lower trim (D), and pull
the front door sill trim (E) up by hand to detach the
clips (F, G), then remove it.
4

. Pull out the front door opening seal (A) from thetrim hooks (B) and around the front door opening
flange, then remove the seal.
08/08/21 15:01:29 61SNR030_200_0068
ProCarManuals.com
DYNOMITE -2009-



Î
(#'

 )
S

pecial Tools Required
20-84 Interior Trim
Headliner Removal/Installation
A
B
C A
B
F
astener Locations
:TORXScrew,2
AB
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S

RS component locations, (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:  Put on gloves to protect your hands.
 Take care not to bend or scratch the trim and panels.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Do the battery terminal disconnection procedure (see page 22-68), and wait at least 3 minutes before
beginning work.
2. Remove these items:  A-pillar trim, both sides (see page 20-69)
 Ceiling light (see page 22-197)
 Front seat belt upper anchor, both sides (see step6 on page 24-4)
 B-pillar lower trim, both sides (see page 20-72)
 B-pillar upper trim, both sides (see page 20-72)
 C-pillar trim, both sides (see page 20-75)
 Grab handles, four places (see page 20-82)
3. Release the tabs (A) from the bracket (B) of the sunvisor cap (C) with a trim tool. 4

. Remove the sunvisor cap (A) from the bracket (B).
5. From both sides, remove the sunvisor (A). –1 Remove the sunvisor from the body and theholder (B).
–2 Remove the screws with a TORX T25 bit.
–3 Remove the sunvisor from the body, and if equipped disconnect the vanity mirror light
connector.
08/08/21 15:01:39 61SNR030_200_0086
ProCarManuals.com
DYNOMITE -2009-




20-85
A
B
B
A
B D
B
5x0.8mm
5N·m
(0.5 kgf·m,
4lbf·ft)
Fastener Locations
:Bolt,2
C
E
F
G A
B
C
A
Fastener Locations :Bolt,4
8x1.25mm
22 N·m
(2.2 kgf·m,
16 lbf·ft) A
6. Push the hook (A) with a flat-tip screwdriver
wrapped with protective tape, and turn the holder
(B) 90 °, then pull it out.
7. Remove the individual map light assembly (A). –1 Remove the lenses (B).
–2 Remove the bolts.
–3 If equipped, release the four tabs (C), then pullout the moonroof switch (D) or the navigation
microphone.
–4 Disconnect the front individual map light connector (E). If equipped, disconnect the
moonroof switch connector (F) and the
navigation microphone connector (G). 8. Without moonroof: Remove the driver’s dashboard
undercover (see page 20-104).
9. Detach the harness clips (A) from the A-pillar (B), and disconnect the roof wire harness connector (C).
10. Remove the center console (see page 20-92).
11. Slide both front seats all the way back, and recline the seat-backs fully.
12. Remove the bolts securing the parking brake base frame (A), and lay it down as needed.
(cont’d)
08/08/21 15:01:40 61SNR030_200_0087
ProCarManuals.com
DYNOMITE -2009-



20-93
A
B
Fastener Locations :Bolt,2
A
B
5x0.8mm
5N·m
(0.5 kgf·m,
4lbf·ft) Fastener Locations
:Bolt,2 :Clip,2
5x0.8mm
5N·m
(0.5 kgf·m,
4lbf·ft)
B
A
5. Pull the center console panel (A) up and rearward to release the tabs (B).
6. Open the armrest (A), and remove the console box mat (B) to access and remove the bolts. 7. Remove the bolts and the clips from the front
portion of the center console. Disconnect the
console subharness connector (A), and detach the
connector clip (B).
(cont’d)
08/08/21 15:02:48 61SNR030_200_0095
ProCarManuals.com
DYNOMITE -2009-



20-94Consoles
Center Console Removal/Installation (cont’d)
A
B
C
B
A
B A
BC
8. Slide both front seats all the way back, and recline
the seat-back fully.
9. Slide the center console (A) rearward to release the pins (B) from the bracket (C).
10. Lift up the rear of the console (A), and remove it from the dashboard.
11. If equipped, disconnect the seat heater switch connectors (B). 12. Install the console in the reverse order of removal,
and note these items:
 Make sure each connector is plugged in properly.
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips and the hooks into place securely.
 When installing the center console panel, install the tabs (A) into the notch (B) of the parking brake
base frame (C).
08/08/21 15:02:48 61SNR030_200_0096
ProCarManuals.com
DYNOMITE -2009-






’06-07 models
’08-09 model
20-125
A
B C
B
A B
C
E F
G
H
D A
A
10. Turn over the reinforcing cloth (A), then release the hooks (B) from the side airbag module holder (C).
Passenger’s seat is shown; driver’s seat is similar.
11. Passenger’s seat: Disconnect the OPDS sensor connectors (A) and the ODS unit subharness
connector (B) from the ODS unit (C), and pull them
in through the hole in the seat frame. Pull the ODS
unit subharness (D) out through the harness hole
(E) in the seat-back cover (F). Detach the harness
clips (G), and remove the wire tie (H). 12. Pinch the tabs on the ends of the head restraint
guides (A), and remove them from the seat-back.
(cont’d)
08/08/21 15:03:58 61SNR030_200_0127
ProCarManuals.com
DYNOMITE -2009-




Left seat-back
Right seat-back
20-141
A
B
B
B
A B
B A
B
C
C
7. Pull back the seat-back cover (A), then release the
hook strips (B). 8. Pull out the seat-back frame (A) from the pad (B),
then pinch the tabs on the ends of the head
restraint guides (C), and remove them from the
seat-back. The left seat-back is shown; the right
seat-back is similar.
9. Remove the seat-back cover and pad from the seat- back frame.
(cont’d)
08/08/21 15:04:07 61SNR030_200_0143
ProCarManuals.com
DYNOMITE -2009-


Î 
20-147
A
B
C
B
A
A
B C
B
4. With the help of an assistant, while pulling the wheel arch portion away from the side spacer (A),
pull the front bumper to release the bumper from
the hooks (B) on the corner upper beam (C).
5. If equipped, disconnect the front fog light connectors (A) while holding the front bumper (B),
then remove the bumper. 6. Release the hooks (A), then remove the front
bumper absorber (B) from the front bumper beam
(C).
7. Install the bumper in the reverse order of removal, and note these items:
 Make sure the front bumper engages the hooks (of both corner upper beams and side spacers)
on each side securely.
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips and the hooks into place securely.
08/08/21 15:04:10 61SNR030_200_0149
ProCarManuals.com
DYNOMITE -2009-