ABS ACURA CSX 2006 Service Repair Manual

Î
How to check for audio system condition
No. 3 button
No. 4 button
No. 5 button
FM button (Push and hold 5 sec.)
CD button (Push and hold 5 sec.)
23-24Audio System
Self-diagnostic Function (cont’d)
A
NOTE:
 The audio unit must be in the code enter screen before performing the self-diagnostic function.
 The self-diagnostic function does not find every problem with the audio system. Check any official H onda service
website for more information about the audio system.
1. Turn the ignition switch to ON (II).
2. Make sure the audio system is turned off.
3. Push and hold the preset No. 1 and No. 6 buttons.
4. While holding the buttons, push the VOL PUSH PWR knob (A) to ON.
5. Release the buttons and the self-diagnostic begins.
6. When you are in the self-diagnostic mode, pressing a preset button starts the diagnostic mode that is assigned to that preset switch.
Entire LCD lighting/light-out mode: Turns on/off the entire LCD to show the presence or absence of an LCD failure.
The entire display must appear. If there are dead segments, replace the audio unit.
Duty indication mode (for the Illumination dim): Indicates the duty for the Illumination dim when the dash lights
are on.
Vehicle speed pulse indication mode: Indicates the vehicle speed pulse.
Reception level check mode: Indicates the reception level (dB). When entering the reception level check mode, the
AM/FM button is used to change the main/sub antenna. See reception level indication for more information.
DRAM residual quantity indication mode: Indicates the DRAM residual quantity.
08/08/21 14:03:50 61SNR030_230_0027
ProCarManuals.com
DYNOMITE -2009-

(#'#

 )

(#'#


 )
23-15723-157
Voice Control Switch Replacement Microphone Replacement
B E
D
A C
B
A
A B
SRS components are located in this area. Review the
SRS component location (see page 24-11).
Also review the precautions and procedures (see page
24-13) in the SRS section before doing repairs or
service.
1. Remove the steering wheel (see page 17-6).
2. Remove the voice control switch (see page 17-7).
3. Install the audio remote switch in the reverse order of removal. 1. Remove the front individual map light lens (A).
2. Remove the bolts (B), then disconnect the
connectors, and remove the map lights housing (C).
3. Carefully pry off the moonroof switch (D) from the map light housing while pressing in on the
retaining tabs (E).
4. From the moonroof switch (A), remove the screw and microphone (B).
5. Install the microphone in the reverse order of removal.
08/08/21 14:08:39 61SNR030_230_0160
ProCarManuals.com
DYNOMITE -2009-

Î
How to check for audio system condition
No. 3 button
No. 4 button
No. 5 button
FM button (Push and hold 5 sec.)
CD button (Push and hold 5 sec.)
23-191
A
NOTE: The audio unit must be in the code enter screen before performing the self-diagnostic function.
 The self diagnostic function does not find every problem with the audio system. Check any official H onda service
website for more information about the audio system.
1. Turn the ignition switch to ON (II).
2. Make sure the audio system is turned off.
3. Push and hold the preset No. 1 and No. 6 buttons.
4. While holding the buttons, push the VOL PUSH PWR knob (A) to ON.
5. Release the buttons and the self-diagnostic begins.
6. When you are in the self-diagnostic mode, pressing a preset button starts.
Entire LCD lighting/light-out mode: Turns on/off the entire LCD to show the presence or absence of an LCD failure.
The entire display must appear. If there are dead segments, replace the audio unit.
Duty indication mode (for the Illumination dim): Indicates the duty for the Illumination dim when the dash lights
are on.
Vehicle speed pulse indication mode: Indicates the vehicle speed pulse.
Reception level check mode: Indicates the reception level (dB). When entering the reception level check mode, the
AM/FM button is used to change the main/sub antenna. See Reception level indication for more information.
DRAM residual quantity indication mode: Indicates the DRAM residual quantity.
(cont’d)
08/08/21 14:09:49 61SNR030_230_0194
ProCarManuals.com
DYNOMITE -2009-


(#'#


 ) Î
(#'#


 )
23-35823-358 Navigation System
HFL-Navigation Microphone
Removal/Installation
GPS Antenna Removal/Installation
B
E
D
A C
B
A
A B A
B
1. Remove the front individual map light lens (A).
2. Remove the bolts (B), then disconnect the
connectors, and remove the map lights housing (C).
3. Carefully pry off the moonroof switch (D) from the map light housing while pressing in on the
retaining tabs (E).
4. From the moonroof switch (A), remove the screw and microphone (B).
5. Install the microphone in the r everse order of
removal. 1. Remove the navigation unit (see page 23-355).
2. Remove the instrument panel visor (see page
20-98).
3. Remove the wire harness clip (A), screws, and GPS antenna (B).
4. Install the antenna in the reverse order of removal.
08/08/21 14:18:35 61SNR030_230_0361
ProCarManuals.com
DYNOMITE -2009-



24-202SRS
Cable Reel Replacement (cont’d)
A
D
B
A C A
39 N·m
(4.0 kgf·m, 29 lbf·ft)
5. Install the steering column covers.
6. If necessary, center the cable reel (new
replacement cable reels come centered). Do this by
first rotating the cable reel clockwise until it stops.
Then rotate it counterclockwise (about three turns)
until the arrow mark (A) on the cable reel label
points straight up.
7. Position the two tabs (A) of the turn signal canceling sleeve (B) as shown, and install the
steering wheel on to the steering column shaft,
making sure the steering wheel hub (C) engages
the pins (D) of the cable reel and tabs of the turn
signal canceling sleeve. Do not tap on the steering
wheel or steering column shaft when installing the
steering wheel. 8. Install a new steering wheel bolt (A), then
reconnect the connectors.
9. Install the driver’s airbag (see page 24-188).
10. Do the battery terminal reconnection procedure (see page 22-68).
11. Clear any DTCs (see page 24-23).
12. After installing the cable reel, confirm proper system operation:
 Turn the ignition switch to ON (II); the SRS indicator should come on for about 6 seconds
andthengooff.
 After the SRS indicator has turned off, turn the steering wheel fully left and right to confirm the
SRS indicator does not come on.
 Make sure the horn and turn signal switches work properly.
 Make sure the steering wheel switches work properly.
Replace.
08/08/21 14:02:00 61SNR030_240_0202
ProCarManuals.com
DYNOMITE -2009-