manual radio set ACURA CSX 2006 Service User Guide

´
´
´
´
(#' 
)
Seek Stop Test
23-7823-78 Audio System
Sound Quality Diagnosis (cont’d)
8. Compare the client’s vehicle’s sound quality results
to the known-good vehicle’s results.
 If the sound quality in the customer’s vehicle is comparable to the sound quality in the known-
good vehicle, then the client’s vehicle is
operating as designed.
 If the sound quality is not comparable, check these items in order.
– Loose or improperly installed speakers or other hardware that may become excited by
the vibrations generated by the speakers
– Poor power or ground to the stereo amplifier (Type S model)
– Damaged speaker(s)
– Faulty amplifier (Type S model)
– Faulty navigation unit
– Faulty audio unit Do this test to check the performance of the audio unit’s
AM and FM reception. Refer to symptom
troubleshooting: audio sound weak or distorted, or no
sound is heard from speakers (display is normal)
(see page 23-39) before continuing with this test.
NOTE:
 Window tint, aftermarket theft-recovery devices and other aftermarket accessories may reduce radio
reception.
 Changes in cloud cover and other atmosphere conditions will affect the ab ility of the navigation unit
or audio unit to receive radio signals.
1. Park the client’s vehicle in an open area away from buildings or other obstructions.
2. Park a known-good vehicle (same year, model, and trim level) next to the client’s vehicle, facing the
same direction.
3. Start the engine in the client’s vehicle, and turn on the radio.
4. Set the FM receiver to 87.7 MHz.
5. Press the Seek button and record the first station that the navigation unit or audio unit locks onto.
6. Press the Seek button repeatedly, and write down each station that the navigation unit or audio
unit locks onto until the station recorded in step 5 is
reached again.
7. Set the AM receiver to 530 kHz.
8. Press the Seek button, and record the first station that the navigation unit or audio unit locks
on to.
9. Press the Seek button repeatedly, and write down each station that the navigation unit or audio
unit locks onto until the station recorded in step 8 is
reached again.
08/08/21 14:05:35 61SNR030_230_0081
ProCarManuals.com
DYNOMITE -2009-

SymptomDiagnostic procedure Also check for
23-99
















 







Voice guidance cannot be heard,
is broken up, or there is static
Symptom Troubleshooting
(see page 23-122) Volume or voice feedback setting (see
Owner’s manual)
Navigation unit
Harness/fuses/switches
Voice control does not work/
respond Symptom Troubleshooting
(see page 23-123) Navigation unit
The wrong color DVD is installed
The DVD is damaged or dirty
Microphone harness/switches
Navigation cannot control HVAC
by voice command Symptom Troubleshooting
(see page 23-130) Wrong color DVD is installed
Harness/fuses/switches
Wrong navigation unit (model code)
Navigation cannot control XM
radio Symptom Troubleshooting
(see page 23-130)Low or weak battery
Navigation cannot control audio
system Symptom Troubleshooting
(see page 23-129)Wrong color DVD
Navigation display buttons do not
work or respond properly Symptom Troubleshooting
(see page 23-121) Navigation unit
Open/short between the XM receiver
or the GA-Net bus
The wrong color DVD is installed
The DVD is damaged or dirty
Today’s Destinations button is
dim and not selectable in the
Enter destination by screen
(grayed-out) The client has not entered a group
of locations for Today’s
Destinations. This is normal. The
button is only selectable if the
client is using this functionSee Owner’s Manual
Some set-up and information
functions of the navigation
system are grayed-out and do not
work Client did not select OK from
Disclaimer screen. Refer to
System Function Diagram
(see page 23-111)
Previous Destinations button is
dim and not selectable in the
Enter destination by screen
(grayed-out) The vehicle may be new, or the
client deleted the destination.
Enter a destination, and allow the
system to route to it. After the trip,
the Previous Destinations button
will be selectable
Address cannot be found or
system gives poor routing Verify proper operation and
system limitations using the
owner’s manual
See Answering customer
question Navigation coverage
in general troubleshooting
Refer to Database limitation in
the navigation system manual
to report database errorsDatabase limitations (address not in
database)
Wrong color DVD installed
OPEN/CLOSE function of the
display does not work Symptom Troubleshooting
(see page 23-132) Navigation unit
Harness
Navigation display will not close Symptom Troubleshooting (see page 23-133) Navigation unit
Harness
Navigation display does not open
or opens part way Symptom Troubleshooting
(see page 23-133) Navigation unit
Harness
PC card will not play/card icon on
audio screen cannot be selected Symptom Troubleshooting
(see page 23-67)Navigation unit
(cont’d)
08/08/21 14:06:26 61SNR030_230_0102
ProCarManuals.com
DYNOMITE -2009-

(#'#
)
Overview
23-101
System Description
The navigation system is a highly sophisticated, hybrid locating system.
The navigation unit uses global positioning system (GPS) satellite signals, internal yaw and vehicle speed inputs, and
a map database to show where the vehicle is and to help guide you to a desired destination.
The navigation unit’s GPS receiver receives signals from the GPS, a network of 24 satellites in orbit ar ound the earth.
By receiving signals from several of these satellites, the navigation system can determine the latitude, l ongitude, and
elevation of the vehicle.
Signals from the system’s yaw rate sensor (inside the navigation unit) detects turns, and the ECM/PCM vehicle speed
pulse (VSP) and reverse signal enable the system to keep track of the vehicle’s speed and direction of travel. The
advantage of this hybrid system is that the system can track your position if either the GPS signal or the vehicle speed
signal is missing. For instance, when in a tunnel (no GPS), the speed signal is used to update your position on the map.
Alternately, while the vehicle is being transported on a ferry, GPS signals can show the vehicle position on the map as
it crosses the water.
The navigation system uses the location, direction, and speed information to display the appropriate map and
calculate a route to the destination entered. As you drive to a destination, the system provides both visual and audio
guidance. Audio guidance is sent to the audio unit, and an RGB graphics color signal is sent to the navigation display.
This navigation system also has voice recognition that allows voice control of most of the navigation, and audio
functions. The voice control switches (navigation TALK and navigation BACK buttons on the steering wheel) activate
the voice control system. The microphone on the ce iling receives your voice commands. For more information on this
feature, consult the navigation owner’s guide.
The illumination signal is used by the navigation unit to automatically switch the display mode between the Night and
Day display modes. When the headlights are on, the dash brightness control setting full brightness overrides the Night
display mode, and allows a daytime navigation display with the lights on.
When the navigation system is giving voice guidance commands, the front speakers are muted. When the voice
control system is being used (navigation TALK button pressed), all of the speakers are muted.
The internal GA-Net II bus passes information back and forth between the navigation display, the navigation unit, and
the audio system components. The information passed on this bus are touch button commands, audio muting signal,
audio (radio and XM), and any open in these bus lines can affect the navigation system or other audio accessory
operation.
The clock on the navigation display is set and maintained by the navigation unit. The time is automatically adjusted for
daylight savings, and time zone changes while driving. The time can be adjusted in setup.
Additional information is available about the navigation components following the System Diagram. A glossary of
terms that are used throughout this section follows the detailed information.
The Navigation System Manual in the glove box covers all of the system functions and settings. Use this as a resource
when evaluating a client concern.
(cont’d)
08/08/21 14:06:26 61SNR030_230_0104
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'#
)

µ
µ µ
µ
µ
µ
µ
µ
YES
NO YES
NO
YES
NO
YES
NO
Picture has lines/rolls/other issues or is an
odd color
23-12023-120Navigation System
Symptom Troubleshooting (cont’d)
NAVIGATION UNIT CONNECTOR A (17P)
RADIO GND
(BLK)
NAVIGATION UNIT CONNECTOR C (12P) GND (BLK)
9. Measure the voltage between navigation unitconnector A (17P) terminal No. 9 and body ground,
and between navigation unit connector C (12P)
terminal No. 4 and body ground.
Replace the navigation unit (see page 23-155).
Repair open in the wire between the
navigation unit and body ground (G 504) (see page
22-30), (G505) (see page 22-32). NOTE:
 Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check the navigation screen settings for brightness, contrast, black level and the color screen for map
color and menu color.
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have the navigation and audio system anti-theft codes.
1. Check for electronic aftermarket accessories (possibly hidden) mounted near the navigation unit.
Disable the accessories, and recheck.
Go to step 2.
2. Turn the ignition switch to ON (II).
3. Start up the navigation picture.
Go to step 5.
Go to step 4.
4. Go into the Diagnostic mode and use RGB Color diagnostic under Monitor Check (see page 23- 137).
Go to step 5.
Replace the navigation unit (see page 23-155).
Wire side of female terminals
Wire side of female terminals
Is t her e l ess t han 0.1 V ? Ar e t her e any el ect r oni c accessor i es?
Is the picture scrolling horizontally (lef t to right orright to left)?
Ar e t he r ed , gr een, and bl ue col or ed ci r cl e show n?
08/08/21 14:07:26 61SNR030_230_0123
ProCarManuals.com
DYNOMITE -2009-

(#'#
)(#'#
)

µ
µ
µ
µ µ
µ
µ
µ
µ
µ
µ
µ
GPS icon is white or not shown Voice guidance cannot be heard, is broken
up, or there is static
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
YES
NO
23-12223-122Navigation System
Symptom Troubleshooting (cont’d)
NOTE:
 Check the vehicle battery condition first.
 Make sure the vehicle is parked outside and away from buildings.
 Refer to GPS Information (see page 23-142) for realtime satellite reception display.
 Check for window tinting above the GPS antenna and any non-OEM accessories mounted near the
navigation unit or GPS antenna.
1. Check for metallic window tint on the windshield and electronic aftermarket accessories (possibly
hidden) mounted near the GPS antenna or the
navigation unit.
Remove tint or the accessories, and
recheck.
Go to step 2.
2. Go into the Diagnostic Menu, and use the Navi System Link test (see page 23-136) to check the
GPS antenna.
Use the Navi ECU test under Unit Check
(see page 23-139) to check for a kinked, crushed, or
disconnected GPS antenna wire. If necessary, try a
known-good GPS antenna. If icon is still red,
replace the navigation unit (see page 23-155).
Check that nothing is blocking the GPS
antenna located behind the gauge assembly, and
recheck. Substitute a known-good navigation unit,
and recheck. NOTE:
 Check the vehicle battery condition first.
 Make sure that the correct DVD color and version are installed.
 Check any official Honda service website for more service information about the navigation system.
 Check that the volume setting and voice feedback are turned ON.
 Check the connectors for poor connection or loose terminals.
 Before troubleshooting, make sure you have the navigation system 4-digit anti-theft code.
 After troubleshooting, enter the navigation system anti-theft code.
1. Press the display unit SET-UP button.
2. Check the volume setting for the navigation system.
Set the volume to an audible level.
Go to step 3.
3. Check the radio operation.
Go to step 4.
Troubleshoot the audio system.
4. Go into the Diagnostic Menu, and use the Navi System Link test (see page 23-136) to check the
radio.
Troubleshoot the audio system.
Go to step 5.
5. Test the voice control switch (see page 23-156).
Replace the navigation unit (see page 23-155).
Replace the voice control switch (see page
23-157).
Is there metallic window tint or electronic accessor ies?
Is the GPS Ant icon red? Is it set to OFF?
Can y ou hear t he r ad i o?
Is the Radio icon red?I s v oi ce cont r ol sw i t ch OK ?
08/08/21 14:07:26 61SNR030_230_0125
ProCarManuals.com
DYNOMITE -2009-

(#'#
)(#'#
)

µ
µ
µ
µ
µ
µ µ
µ
µ
µ
Navigation display stays on with ignition
switch in LOCK (0) Navigation cannot control audio system
YES
NO
YES
NO
YES
NO YES
NO
YES
NO
23-12923-129
NOTE:
 Check the connectors for poor connections or loose terminals.
 Before troubleshooting, get the navigation system anti-theft code, then write down the audio presets.
 After troubleshooting, re-enter the anti-theft code, and re-initialize the navigation system, then enter the
audio presets.
 Check for aftermarket accessories that use the same power circuit. A feedback can cause this problem.
1. Remove the key from the ignition.
Go to step 2.
The system is OK at this time.
2. The vehicle may have been used as a demonstration vehicle at an event like an auto
show. In these events, power is often jumpered to
the navigation system so that the ignition key is not
needed in the vehicle. At the end of the show, the
jumper wire may not have been removed. Check
the navigation unit connector A (17P) for a non-
factory jumper wire in series with the factory cable.
Remove the jumper wire, and re-test. Return
the jumper wire to Tech Line.
Go to step 3.
3. Check if the audio unit works.
Troubleshoot the ACC circuit for a short to
power with another circuit.
Replace the navigation unit (see page 23-155). NOTE:
 Check the vehicle battery condition first.
 Verify that the correct navigation unit is installed for this model. Go into the Diagnostic mode and use
Version (see page 23-149).
 Check for connectors for poor connections or loose terminals.
 Before troubleshooting, make sure you have anti- theft codes for the navigation system.
 After troubleshooting, enter the anti-theft codes for the navigation system.
 Make sure that the correct navigation DVD color and version are installed.
 Inspect the navigation DVD for dirt or damage.
 Check any official Honda service website for more service information about the navigation system.
1. Make sure the anti-theft code for the navigation system is entered.
2. Go into the Diagnostic Menu and use the Navi System Link test (see page 23-136).
Do the troubleshooting for the voice
guidance cannot be heard (see page 23-122).
Go to step 3.
3. Substitute a known-good navigation unit (see page 23-155), and recheck.
Replace the navigation unit (see page 23-155).
Do the audio system troubleshooting.
Does t he nav i gat i on scr een st ay on?
Is t her e a j umper w i r e?Does the audio unit work with the ignition switchoff? Is the Radio icon red?
Can t he nav i gat i on cont r ol aud i o?
08/08/21 14:07:28 61SNR030_230_0132
ProCarManuals.com
DYNOMITE -2009-

´
´µ
Î Î
´
Touch Panel CalibrationUnit Check
23-139
Return
Set
1 2
3 4
5Please press the center of’’ ’’button.
Select Check UnitsReturn
Display Radio
Navi ECU PC Card Info.
Hard Key
The display screen uses a touch sensitive membrane.
This means that every location of the entire surface of
the display is touch sensitive. This diagnostic allows
alignment of these touch locations with the location of
the buttons images on the screen.
Normally this should n ever need adjustment, and is
used only to adjust the touch locations for parallax (the
touch locations appear different when viewed at an
angle). However, if an adjustment is necessary, follow
this procedure:
 The screen consists of the button icons. Touch the center of the five buttons on order 1 5.
 To store any change you make, touch the Set button.
 Use the Return key to exit the diagnostic. Select the item you want to check, and the test starts.
Display
Radio
 Navi ECU
PCCardInfo
 Hard Key
(cont’d)
08/08/21 14:07:30 61SNR030_230_0142
ProCarManuals.com
DYNOMITE -2009-

Î
ÎÎ
µ
µ
µ
Display
Radio Navi ECU
23-140Navigation System
System Diagnostic Mode (cont’d)
Display
OK
OK
Connection
Version 040423
RadioOK
Connection
OK
0mV
AM Electric Field Intensity
0mV
FM Electric Field Intensity
7150
CD Mech. Version Navi ECU
OK
VRAM
OK
OK
DRAM
OK
GPS
DVD ROM
Serial NO.
ABC01234567
Mem Clear
-Return
Return
Return
This performs additional checks on the communication
bus between navigation CPU and the display. In
addition, the test checks the internal electronic
functions.
If the connection is NG, replace the navigation unit.
 Connection verifies internal communications.
 Version represents the software version for the display.
This diagnostic screen checks the internals of the radio
(AM and FM) and CD player. If NG, replace the
navigation unit. This screen looks for problems with the navigation unit.
When you initiate this diagnostic, the navigation unit
may freeze of delay up to a minute while the diagnostic
runs.
 If V-RAM or D-RAM is NG, then replace the navigation unit.
 If GPS indicates NG (ANT), check the entire GPS antenna wire from the navigation unit to the antenna.
If the wire is crushed or damaged, try a known-good
antenna. If this diagnostic reads OK, then order a new
GPS antenna. If the diagnostic still reads NG (ANT),
replace the navigation unit.
 DVD ROM represents the database version on the DVD. You can also find this information in setup by
selecting System Information.
 Serial No. should be the same as the serial number found on the underside of the navigation unit. You
need this number to obtain the security code from the
Interactive Network system.
 Mem Clear is for factory use, and should never be used unless instructed by the factory. Accidental
selection will erase the client’s personal data, PINS,
and settings. If selected, a popup box appears asking
if you want to clear the memory. If so, select Yes.
08/08/21 14:07:31 61SNR030_230_0143
ProCarManuals.com
DYNOMITE -2009-

(#'
)
Symptom Diagnostic procedure Also check for
23-162
Audio System
Symptom Troubleshooting Index
Poor AM or FM radio reception or
interference (with navigation)
Symptom Troubleshooting (see page 23-
196) AM/FM antenna lead and/or
sublead short or open in the
wire
Poor AM or FM radio reception or
interference (without navigation) Symptom Troubleshooting (see page 23-
199) AM/FM antenna lead and/or
sublead short or open in the
wire
Audio unit power switch will not
turn on (No information display
and no sound) (with navigation) Symptom Troubleshooting (see page 23-
202)
Audio unit power switch will not
turn on (No information display
and no sound) (without
navigation) Symptom Troubleshooting (see page 23-
203)
Audio unit power switch will not
turn off (with navigation) Symptom Troubleshooting (see page 23-
205)
Audio unit power switch will not
turn off (without navigation) Symptom Troubleshooting (see page 23-
206)
No sound is heard from the
speaker(s) (display is normal)
(with navigation) Symptom Troubleshooting (see page 23-
206)
No sound is heard from the
speaker(s) (display is normal)
(without navigation) Symptom Troubleshooting (see page 23-
215)
Auxiliary i nput sound is low or
cannot be heard Symptom Troubleshooting (see page 23-
217)
Audio system sound is weak or
distorted (display is normal) Symptom Troubleshooting (see page 23-
220)
Radio preset memory is lost Symptom Troubleshooting (see page 23-221) Internal error
Volume does not change Symptom Troubleshooting (see page 23- 221)
Volume does not increase with
speed (with navigation) Symptom Troubleshooting (see page 23-
222)
Volume does not increase with
speed (without navigation) Symptom Troubleshooting (see page 23-
223)
Volume is too high or too low
when driving at freeway speeds Symptom Troubleshooting (see page 23-
224)
Radio tuner does not change
stations Symptom Troubleshooting (see page 23-
224)
08/08/21 14:08:45 61SNR030_230_0165
ProCarManuals.com
DYNOMITE -2009-

SymptomDiagnostic procedure Also check for
23-163
Navigation unit button
illumination does not work (with
navigation)Symptom Troubleshooting (see page 23-
225)
Audio unit button illumination
does not work (without
navigation) Symptom Troubleshooting (see page 23-
226)
Display does not dim or brighten
with dimmer (without navigation) Symptom Troubleshooting (see page 23-
227)
Audio disc does not load Symptom Troubleshooting (see page 23- 228)
Audio disc does not eject Symptom Troubleshooting (see page 23-228)
Audio disc does not play Symptom Troubleshooting (see page 23- 229)
Audio disc skips Symptom Troubleshooting (see page 23- 229)
Audio remote switch does not
work properly (with navigation) Symptom Troubleshooting (see page 23-
230)
Audio remote switch does not
work properly (without
navigation) Symptom Troubleshooting (see page 23-
232)
Audio disc cannot be inserted
and/or ejected (with navigation) Symptom Troubleshooting (see page 23-
233)
Display can be opened and/or
closed even when an audio disc is
being inserted or ejected Replace the navigation unit (see page
23-355)
PC card will not play/card icon on
audio screen cannot be selected
(with navigation) Symptom Troubleshooting (see page 23-
234)
USB input sound is low or cannot
be heard (with navigation) Symptom Troubleshooting (see page 23-
235) Requirement of the USB
devices (see Owner’s Manual)
USB input sound is low or cannot
be heard (without navigation) Symptom Troubleshooting (see page 23-
236) Requirement of the USB
devices (see Owner’s Manual)
USB device does not function
(with navigation) Symptom Troubleshooting (see page 23-
238) Requirement of the USB
devices (see Owner’s Manual)
USB device does not function
(without navigation) Symptom Troubleshooting (see page 23-
241) Requirement of the USB
devices (see Owner’s Manual)
Error code: XM NO SIGNAL or XM
ANTENNA is displayed (with
navigation) Symptom Troubleshooting (see page 23-
245)
XM radio display is blank and no
station information is displayed
(with navigation) Symptom Troubleshooting (see page 23-
245)
XM radio preset memory is lost
(with navigation) Symptom Troubleshooting (see page 23-
248)
Poor or no sound with XM radio
(Audio unit does display XM
channels) (with navigation) Symptom Troubleshooting (see page 23-
249)
08/08/21 14:08:45 61SNR030_230_0166
ProCarManuals.com
DYNOMITE -2009-