washer fluid ACURA CSX 2006 Service User Guide

Î
 
(#'



 )
Automatic Transmission Fluid Capacity:
2.9 L (3.1 US qt) at change
6.5 L (6.9 US qt) at overhaul
14-232 Automatic Transmission
ATF Replacement
A
18 x 1.5 mm
49 N·m
(5.0 kgf·m,
36 lbf·ft)
B
ATF
A
NOTE: Keep all foreign particles out of the transmission. 1. Park the vehicle on the level ground.
2. Warm up the engine to normal operating temperature (the radiator fan comes on), and turn
the engine off.
3. Remove the drain plug (A), and drain the automatic transmission fluid (ATF).
4. Reinstall the drain plug with a new sealing washer (B).
5. Refill the transmission with ATF into the dipstick hole to bring the fluid level between the upper
mark and the lower mark of the dipstick. Always
use Acura ATF-Z1 automatic transmission fluid
(ATF). Using a non-Acura ATF can affect shift
quality.
6. Check that the ATF level is between the upper mark
and the lower mark of the dipstick.
7. Insert the dipstick back into the transmission with the letters ‘‘ATF’’ pointing toward the front of the
vehicle. 8. If the maintenance minder required to replace the
ATF, reset the maintenance minder (see page 3-4),
and this procedure is complete. If the maintenance
minder did not require you to replace the ATF, go
to step 9.
9. Connect the HDS to the DLC (A) located under the driver’s side of the dashboard.
10. Turn the ignition switch to ON (II). Make sure the HDS communicates with the PCM. If it does not, go
to the DLC circuit troubleshooting (see page
11-204).
11. Select BODY ELECTRICAL with the HDS.
12. Select ADJUSTMENT in the GAUGES MENU with the HDS.
13. Select RESET in the MAINTENANCE MINDER MENU with the HDS.
14. Select RESETTING THE ATF with the HDS.
NOTE: If you changed the engine oil at the same
time with the ATF, select RESETTING THE ENGINE
OIL LIFE AND ATF with the HDS instead.
Replace.
08/08/21 14:46:53 61SNR030_140_0234
ProCarManuals.com
DYNOMITE -2009-

ÌÏ Î

(#'


 )
Special Tools Required
14-233
Transmission Removal
A
18x1.5mm
49 N·m
(5.0 kgf·m, 36 lbf·ft)
B
A
B
 Engine hanger plate 07AAK-SNAA120
 Engine support hanger, A and Reds AAR-T
1256
 2006 Civic engine hanger VSB02C000025
 Front subframe adapter VSB02C000016 Available through Acura Canada Technical Tools
Department; Fax 866-398-8665/
e-mail: ch_technicaltools ch.honda.com
NOTE:  Use fender covers to avoid damaging painted surfaces.
 Special tool engine support hanger must be used with the side engine mount installed.
1. Remove the cowl cover (see page 20-163) and the under-cowl panel.
2. Remove the front grille cover (see page 20-163).
3. Do the battery removal procedure (see page 22-69).
4. Remove the intake air duct (see page 11-348) and the air cleaner assembly (see page 11-345).
5. Remove the battery tray, the battery base, and the resonator.
6. Raise the vehicle on a lift, and make sure it is securely supported and remove the front wheels.
7. Remove the splash shield. 8. Remove the drain plug (A), and drain the automatic
transmission fluid (ATF).
9. Reinstall the drain plug with a new sealing washer (B).
10. Secure the hood in the vertical position.
11. Remove the harness cover (A) from its bracket (B).
(cont’d)
Replace.
08/08/21 14:46:53 61SNR030_140_0235
ProCarManuals.com
DYNOMITE -2009-


(#'
")


(#'
 )
16-416-4 Driveline/Axle
Driveshaft Inspection
Driveshaft Removal
F
D B
C
A
E A
B
1. Check the inboard boot (A) and the outboard boot (B) on the driveshaft (C) for cracks, damage, leaking
grease, and loose boot bands (D). If any damage is
found, replace the boot and the boot bands.
2. Check the driveshaft for cracks and damage. If any damage is found, replace the driveshaft.
3. Check the inboard joint (E) and the outboard joint (F) for cracks and damage. If any damage is found,
replace the inboard joint or the outboard joint as an
assembly.
4. Hold the inboard joint and turn the front wheel by hand, then make sure the joint is not excessively
loose. If necessary, replace the inboard joint or the
outboard joint as an assembly. 1. Raise the vehicle on a lift.
2. Remove the front wheels.
3. Pry up the locking tab (A) on the spindle nut (B),
then remove the nut.
4. Drain the transmission fluid, then reinstall the drain plug with a new sealing washer:
 5-speed manual transmission (see page 13-5)
 6-speed manual transmission (see page 13-82)
 Automatic transmission (see page 14-232)
5. Remove the nuts and the bolt, then separate the lower arm using a prybar.
08/08/21 14:51:21 61SNR030_160_0004
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
16-23
Intermediate Shaft Removal
A B A
B
1. Drain the transmission fluid. Reinstall the drain
plug with a new sealing washer:
 5-speed manual transmission (see page 13-5)
 6-speed manual transmission (see page 13-82)
 Automatic transmission (see page 14-232)
2. Remove the right driveshaft (see page 16-4).
3. Remove the three flange bolts, then remove the heat shield.
4. Remove the flange bolt (A) and the two shoulder bolts (B). 5. Remove the intermediate shaft (A) from the
differential. Hold the intermediate shaft horizontally
until it is clear of the differential to prevent
damaging the oil seal (B).
08/08/21 14:51:45 61SNR030_160_0023
ProCarManuals.com
DYNOMITE -2009-


(#'



!)

Except Type S Model
19-22Conventional Brake Components
Front Brake Caliper Overhaul
INNER PAD SHIM B
WEAR INDICATOR
OUTER PAD SHIM
INNER PAD SHIM A BRAKE PADS CALIPER
PIN B CALIPER PIN
12x1.25mm
108 N·m
(11.0 kgf·m,
79.6 lbf·ft)CALIPER
BRACKET
BLEED SCREW
9N·m
(0.9 kgf·m,
7lbf·ft) CALIPER
BODY
PAD RETAINERS
PISTON
BRAKE HOSE
BANJO BOLT
34 N·m
(3.5 kgf·m,
25 lbf·ft) PISTON SEAL
: Honda silicone grease (P/N 08C30-B0234M)
SEALING
WASHERS 10x1.0mm
50 N·m
(5.1 kgf·m, 37 lbf·ft) CALIPER PIN APIN BOOT
PISTON BOOT
Frequent inhalation of brake pad dust, regardless of material composition, could be hazardous to your health.  Avoid breathing dust particles.
 Never use an air hose or brush to clean brake assemblies. Use an OSHA-approved vacuum cleaner.
Remove, disassemble, inspect, reassemble, and install the caliper, and note these items:
NOTE: Make sure that the caliper pins are installed correctly. Upper caliper pin B and lower caliper pin A are different.
If these caliper pins are installed in the wrong location, it will cause vibration, uneven or rapid brake pad wear, and
possibly uneven tire wear.  Do not spill brake fluid on the vehicle; it may damage the paint; if brake fluid gets on the paint, wash it off immediately with water.
 To prevent dripping brake fluid, cover disc onnected hose joints with rags or shop towels.
 Clean all parts in brake fluid and air dry; blow out all passages with compressed air.
 Before reassembling, check that all parts are free of dirt and other foreign particles.
 Replace parts with new ones as specified in the illustration.
 Make sure no dirt or other foreign matter gets in the brake fluid.
 Make sure no grease or oil gets on the brake discs or pads.
 When reusing brake pads, always reinstall them in their original positions to prevent loss of braking efficiency.
 Do not reuse drained brake fluid. Use only clean Honda DOT 3 Brake Fluid from an unopened container. Using a non-Honda brake fluid can cause corrosion and shorten the life of the system.
 Coat the piston, the piston seal groove, and the caliper bore with clean brake fluid.
 Use recommended greases in the front caliper set.
 After installing the caliper, check the brake hose and line for leaks, interference, and twisting.
Install inner brake pad with
its wear indicator upward.
Replace.
Replace. Replace.
Replace.
08/08/21 15:00:58 61SNR030_190_0022
ProCarManuals.com
DYNOMITE -2009-


(#'



!)

Type S Model
19-23
INNER PAD SHIM B WEAR INDICATOR
OUTER PAD SHIM A
INNER PAD SHIM A BRAKE PADS CALIPER PIN B
CALIPER PIN
PIN BOOT
12 x 1.25 mm
108 N·m
(11.0 kgf·m,
79.6 lbf·ft) CALIPER
BRACKET
CALIPER PIN A
BLEED SCREW
9N·m
(0.9 kgf·m,
7lbf·ft)
CALIPER
BODY
PAD RETAINERS
PISTON
PISTON BOOT
BRAKE HOSE
BANJO BOLT
34 N·m
(3.5 kgf·m,
25 lbf·ft) PISTON SEAL
: Honda silicone grease (P/N 08C30-B0234M)
SEALING
WASHERS 8x1.0mm
33 N·m
(3.4 kgf·m, 25 lbf·ft)OUTER PAD SHIM B
Frequent inhalation of brake pad dust, regardless of material composition, could be hazardous to your health.
 Avoid breathing dust particles.
 Never use an air hose or brush to clean brake assemblies. Use an OSHA-approved vacuum cleaner.
Remove, disassemble, inspect, reassemble, and install the caliper, and note these items:
NOTE: Make sure that the caliper pins are installed correctly. Upper caliper pin B and lower caliper pin A are different.
If these caliper pins are installed in the wrong location, it will cause vibration, uneven or rapid brake pad wear, and
possibly uneven tire wear.  Do not spill brake fluid on the vehicle; it may damage the paint; if brake fluid gets on the paint, wash it off immediately with water.
 To prevent dripping brake fluid, cover disc onnected hose joints with rags or shop towels.
 Clean all parts in brake fluid and air dry; blow out all passages with compressed air.
 Before reassembling, check that all parts are free of dirt and other foreign particles.
 Replace parts with new ones as specified in the illustration.
 Make sure no dirt or other foreign matter gets in the brake fluid.
 Make sure no grease or oil gets on the brake discs or pads.
 When reusing brake pads, always reinstall them in their original positions to prevent loss of braking efficiency.
 Do not reuse drained brake fluid. Use only clean Honda DOT 3 Brake Fluid from an unopened container. Using a non-Honda brake fluid can cause corrosion and shorten the life of the system.
 Coat the piston, the piston seal groove, and the caliper bore with clean brake fluid.
 Use recommended greases in the front caliper set.
 After installing the caliper, check the brake hose and line for leaks, interference, and twisting.
Install inner brake pad with
its wear indicator upward. Replace.
Replace.
Replace.
Replace.
08/08/21 15:00:59 61SNR030_190_0023
ProCarManuals.com
DYNOMITE -2009-



(#'


 )
19-24 Conventional Brake Components
Master Cylinder Replacement
B
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A B
D
E G
MASTER
CYLINDER SIDE
A
ABS: 15 N·m
(1.5 kgf·m, 11 lbf·ft)
VSA: 22 N·m
(2.2 kgf·m, 16 lbf·ft) C
15 N·m
(1.5 kgf·m,
11 lbf·ft)
D
F
 Do not spill brake fluid on the vehicle; it may damage the paint; if brake fluid gets on the paint,
wash it off immediately with water.
 Be careful not to damage or deform the brake lines during removal and installation.
 Plug the ends of the hoses and the joints to prevent spilling brake fluid.
1. Remove the air cleaner (see page 11-345).
2. Remove the reservoir cap and brake fluid from the master cylinder reservoir with a syringe.
3. Disconnect the brake fluid l evel switch connector
(A).
4. Remove the reservoir tank mounting bolt (B). 5. Disconnect the brake lines (A) from the master
cylinder (B). To prevent spills, cover the hose joints
with clean rags or shop towels.
6. Remove the master cylinder mounting nuts (C) and washers (D).
7. Remove the master cylinder from the brake booster (E). Be careful not to bend or damage the brake
lines when removing the master cylinder.
8. Remove the rod seal (F) from the master cylinder. NOTE: During installation, set a new rod seal onto
the master cylinder with its grooved side (G)
toward the master cylinder.
9. Install the master cylinder in the reverse order of removal, and note these items:
 Coat the inner bore lip and outer circumference of the new rod seal with the Shin-Etsu silicone
grease (P/N 08798-9013).
 Make sure not to get any silicone grease on the terminal part of the connectors and switches,
especially if you have silicone grease on your
hands or gloves.
 Check the brake pedal height and free play after installing the master cylinder, and adjust it if
necessary (see page 19-6).
10. Bleed the brake system (see page 19-9).
11. Spin the wheels to check for brake drag.
Replace.
08/08/21 15:00:59 61SNR030_190_0024
ProCarManuals.com
DYNOMITE -2009-


(#'



!)
19-35
Rear Brake Caliper Overhaul
BRAKE HOSE8x1.0mm
23 N·m
(2.3 kgf·m, 17 lbf·ft)
SEALING WASHERS
BANJO BOLT
34 N·m
(3.5 kgf·m, 25 lbf·ft)
BLEED SCREW
9 N·m (0.9 kgf·m, 7 lbf·ft)
CALIPER BODY
RODO-RING
SLEEVE PISTON
CUP ADJUSTING BOLT
BEARING A
SPACER
ADJUSTING SPRING B
PISTON BOOT
PISTON SEAL
PISTON
ASSEMBLY
CIRCLIP
SPRING
GUIDE
SHAFT
SHAFT COVER
LEVER ARM
SPRING
WASHER PARKING NUT
27 N·m
(2.8 kgf·m, 20 lbf·ft) RETURN
SPRING
23 N·m
(2.3 kgf·m,
17 lbf·ft)
INNER PAD
SHIM BRAKE PADS PAD SPRING
CALIPER PIN A CALIPER PIN B
PAD
RETAINERS
CALIPER
BRACKET
: Honda silicone grease (P/N 08C30-B0234M)
OUTER PAD SHIM
WEAR INDICATOR
CALIPER PIN PIN BOOT 10x1.25mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)
Frequent inhalation of brake pad dust, regardless of material composition, could be hazardous to your health.
 Avoid breathing dust particles.
 Never use an air hose or brush to clean brake assemblies. Use an OSHA-approved vacuum cleaner.
Remove, disassemble, inspect, reassemble, and install the caliper, and note these items:
NOTE: Make sure that the caliper pins are installed correctly. Upper caliper pin B and lower caliper pin A are different.
If these caliper pins are installed in the wrong location, it will cause vibration, uneven or rapid pad wear, and possibly
uneven tire wear.  Do not spill brake fluid on the vehicle; it may damage the paint; if brake fluid gets on the paint, wash it off immediately with water.
 To prevent dripping brake fluid, cover disc onnected hose joints with rags or shop towels.
 Clean all parts in brake fluid and air dry; blow out all passages with compressed air.
 Before reassembling, check that all parts are free of dirt and other foreign particles.
 Replace parts with new ones as specified in the illustration.
 Make sure no dirt or other foreign matter gets into the brake fluid.
 Make sure no grease or oil gets on the brake discs or pads.
 When reusing brake pads, always reinstall them in their original positions to prevent loss of braking efficiency.
 Do not reuse drained brake fluid. Use only clean Honda DOT 3 Brake Fluid from an unopened container. Using a non-Honda brake fluid can cause corrosion and shorten the life of the system.
 Coat the piston, the piston seal groove, and the caliper bore with clean brake fluid.
 Use recommended greases in the rear caliper set.
 After installing the caliper, check the brake hose and line for leaks, interference, and twisting.
Replace.
Replace.
Replace. Replace.
Replace.
Replace.
Install inner pad
with its wear
indicator downward. Replace.
08/08/21 15:02:07 61SNR030_190_0035
ProCarManuals.com
DYNOMITE -2009-

Entry Lights Control System
Power Windows
Wipers/Washers
GaugesReminder Systems
Moonroof
Accessory Power Sockets
Seat Heaters
Power Mirrors
Rear Window Defogger
Immobilizer System......................
.......................................... ......................................... ...........................
.............................. ......................
.......................................... ......................................... ...........................
..............................
Component Location Index . 22-202
Circuit Diagram . 22-203
MICU Input Test . 22-204
Ignition Key Switch Test . 22-207
Ignition Key Light Test . 22-207
......................
...................................
............................................ ..........................................
.......................................................... ........
.......................................................... ..................................
........................................................
...................................
............................................ ..........................................
.......................................................... ........
.......................................................... ..................................
..................................
Component Location Index
. 22-208
System Description . 22-209
Resetting the Power Window Control Unit . 22-210
Circuit Diagram . 22-212
Power Window Master Switch Input Test . 22-214
Driver’s Power Window Motor Test . 22-217
Passenger’s Power Window Motor Test . 22-218
Power Window Master Switch Test/Replacement . 22-219
Passenger’s Power Window Switch Test/Replacement . 22-220
......................
.......................................... ................................
......................................... .......................
....................................... .................................... ...............
....................... ........
...............
........................ ................
...................... ......................
.......................................... ................................
......................................... .......................
....................................... .................................... ...............
....................... ........
...............
........................ ................
......................
Component Location Index
. 22-221
Circuit Diagram . 22-223
DTC Troubleshooting . 22-224
MICU Input Test . 22-228
Wiper/Washer Switch Test . 22-231
Wiper Motor Test . 22-231
Washer Motor Test . 22-232
Washer Fluid Level Switch Test . 22-232
Wiper Motor Replacement . 22-233
Wiper/Washer Switch Replacement . 22-234
Washer Reservoir Replacement . 22-234
Wiper Blade Replacement . 22-235
Wiper Arm/Nozzle Adjustment . 22-236
Washer Tube Replacement . 22-237
......................
...........................
.......................................... ................................
................................................
................................................
......................................
..............................................
..................................
.............................................. ......................
...........................
.......................................... ................................
................................................
................................................
......................................
..............................................
..................................
..............................................
Component Location Index
. 22-238
Self-diagnostic Function . 22-241
Circuit Diagram . 22-244
DTC Troubleshooting . 22-262
Gauge Control Module (Tach) Input Test . 22-271
Gauge Control Module (Speedo) Input Test . 22-274
Rewriting the ODO Data and Transferring the Maintenance
Minder Data to a New Gauge
Control Module . 22-276
Replacement . 22-277
Dash Lights Brightness Controller and Odometer Select/Reset Switch
Test/Replacement . 22-278
Outside Air Temperature Indicator Calibration . 22-279 ......................
.......................................... ......................................... ......................
.......................................... .........................................
Component Location Index
. 22-281
Circuit Diagram . 22-282
MICU Input Test . 22-284
...................... ......
.......................................... ...................
......................
......
.......................................... ...................
Component Location Index
. 22-286
Resetting the Moonroof Control Unit . 22-287
Circuit Diagram . 22-288
Moonroof Control Unit Input Test . 22-290
Moonroof Switch Test/Replacement . 22-293
......................
..........................................
..................................
.................................. ......................
..........................................
..................................
..................................
Component Location Index
. 22-294
Circuit Diagram . 22-295
Front Accessory Power Socket Test/Replacement . 22-296
Console Accessory Power Socket Test/Replacement . 22-297
......................
.......................................... .........................
........................................ ......................
.......................................... .........................
........................................
Component Location Index
. 22-298
Circuit Diagram . 22-300
Switch Test/Replacement . 22-302
Seat Heater Test . 22-302
......................
..........................................
..............................................
........................................................ .......
......................
..........................................
..............................................
........................................................ .......
Component Location Index
. 22-304
Circuit Diagram . 22-305
Function Test . 22-306
Power Mirror Switch Test/Replacement . 22-307
Power Mirror Actuator Test . 22-307
Power Mirror Actuator Replacement . 22-308
......................
..........................................
.............................................. ......................................................
..........................................
.............................................. ................................
Component Location Index
. 22-310
Circuit Diagram . 22-311
Function Test . 22-312
Defogger Wire Repair . 22-313
......................
...................................
.......................................... ................................
............................................. ......................
............................................
.................................................. ...................
................................................ ........................................... ......................
...................................
.......................................... ................................
............................................. ......................
............................................
.................................................. ...................
................................................ ...........................................
Component Location Index
. 22-314
System Description . 22-315
Circuit Diagram . 22-316
DTC Troubleshooting . 22-317
Symptom Troubleshooting Information . 22-321
Symptom Troubleshooting . 22-323
System Check . 22-326
Status Log . 22-328
Immobilizer Key Registration . 22-329
Immobilizer-Keyless Control Unit Input Test . 22-330
Immobilizer-Keyless Control Unit Replacement . 22-332
08/08/21 14:22:03 61SNR030_220_0003
ProCarManuals.com
DYNOMITE -2009-

µ
(#'
)
GroundComponent or Circuit Grounded
22-64Ground Distribution
Ground to Components Index
G1 Battery
G2 Engine
G3 Transmission housing
G101 A/T clutch pressure control solenoid valves A, B, C (A/T), CKP sensor, CMP sensor A, CMP sensor B, Data link connector (DLC), ECM/PCM (LG1), ECM/PCM (LG2), ECM/PCM (PG1), ECM/PCM (PG2), ECM/PCM (PGMETCS), EGR valve (K20Z2 engine), Ignition
coils, Immobilizer-keyless control unit, Rocker arm oil control solenoid, Rocker arm oil pressure switch, Transmission range
switch (A/T), VTC oil control solenoid valve
Shielding between the ECM/PCM and Knock sensor (KS) has wire.
Shielding between the ECM/PCM and Secondary HO2S (Sensor 2) has wire.
G201 Right fog light , Right front parking light, Right front side marker light, Right front turn signal light, Right headlight (high/low beams), Right HID unit , Windshield washer motor, Windshield wiper motor
G202 ABS modulator-control unit , VSA modulator-control unit
G301 A/C condenser fan motor, Blower motor relay, ELD, Left fog light , Left front parking light, Left front side marker light, Left front turn signal light, Left headlight (high/low beams), Left HID unit , Radiator fan motor (via fan control relay)
G401 Brake fluid level switch, Clutch interlock switch (M/T), Clutch pedal position switch (M/T), Hood switch, MICU (PG), Power transistor, Washer fluid level switch (G401 connects to G601 via under-dash fuse/relay box)
G402 EPS control unit
G403 Torque sensor
G501 Dash lights brightness controller and odometer select/reset switch, Driver’s door key cylinder switch, Driver’s door lock knob switch, HandsFreeLink control unit , MICU (SG), VSA OFF switch
G502 Data link connector (DLC), Front accessory power socket, Glove box light, Right power mirror defogger, Right side turn signal light
G503 Accessory power socket relays (front and console), Driver’s door lock switch, Gauge control module (tach), Left power mirror defogger, Left side turn signal light, Moonroof control unit/motor, Power mirror switch light, Power mirror switch, Power
window master switch (main switch), Power window master switch, Vanity mirror lights (driver’s and front passenger’s)
G504 Cable reel (steering wheel switches ground), Climate control unit, Front passenger’s door lock knob switch, Front passenger’s door lock switch, Gauge control module (speedo), Gauge control module (tach), Ignition key switch, Navigation unit , TPMS
control unit
G505 Audio unit , Navigation unit
G506 Memory erase signal (MES) connector, SRS unit (2 wires)
G601 A/T gear position console panel light/Park-pin switch (A/T), Console accessory power socket , Fuel pump, MICU (PG), Seat heater relays (driver’s and front passenger’s), Seat heater switches (driver’s and front passenger’s), Seat heaters (driver’s and
front passenger’s), Stereo amplifier (G601 connects to G401 via under-dash fuse/relay box)
Shielding between the left side impact sensor (FIRST) and rear safing sensor has wire.
Shielding between the SRS unit and left side impact sensor (FIRST) has wire.
G602 Driver’s seat belt buckle switch, Front passenger’s seat belt buckle switch, Left rear door lock knob switch, MICU (SG), MICU service check connector, ODS unit, Right rear door lock knob switch, Yaw rate-lateral acceleration sensor
Shielding between the right side impact sensor (FIRST) and right side impact sensor (SECOND) have wires.
Shielding between the SRS unit and right side impact sensor (FIRST) has wire.
G603 Noise condenser Shielding between the rear safing sensor and left side impact sensor (SECOND) has wire.
G701 High mount brake light, Left back-up light, Left inner taillight, Left rear side marker light, Left rear turn signal light, Left taillight/ brake light, License plate lights, Right back-up light, Right inner taillight, Right rear side marker light, Right rear turn signal light,
Right taillight/brake light, Trunk lid release actuator/Trunk lid latch switch
G801 Rear window defogger ( )
1: ’06-07 Touring and Premium models
2: ’07 TYPE S and ’08-09 models
3: ’08-09 models
4: TYPE S and ’08 premium and ’09 models
5: With HID
6: Without navigation system
7: With navigation system
8: ’09 model with navigation system
9: ’06-08 models, and ’09 model without navigation system
10: TYPE S model
4
512 4
5
82 3
7
3
67
9
10
2
08/08/21 14:24:03 61SNR030_220_0066
ProCarManuals.com
DYNOMITE -2009-