windshield wipers ACURA CSX 2006 Service User Guide


(#'
 ) 

(#'
 ) Washer reservoir capacity: 4.5 L (4.8 US qt)
22-23422-234
Wipers/Washers
Wiper/Washer Switch Replacement Washer Reservoir Replacement
A
B B
D AC
A
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
B
1. Remove the driver’s dashboard lower cover
(see page 20-102).
2. Remove the steering column covers (see page 17-9).
3. Disconnect the dashboard wire harness 8P connector (A) from the wiper/washer switch (B).
4. Remove the two screws, then slide out the wiper/ washer switch.
5. Install the wiper/washer switch in the reverse order of removal. 1. Remove the right inner fender (see page 20-171).
2. Disconnect the 2P connector(s) (A) from the
windshield washer motor (B) and the washer fluid
level switch (C).
3. Disconnect the windshield washer tube (D).
4. Remove the bolts (A) and the clip (B), then remove the washer reservoir.
5. Install the washer reservoir in the reverse order of removal.
08/08/21 14:28:50 61SNR030_220_0236
ProCarManuals.com
DYNOMITE -2009-


(#' ) 

(#' )
’06-07 models ’08-09 models
22-23522-235
Wiper Blade Replacement
A
D
B C C
A B
A B
A
B
1. Lift the wiper arm off the windshield, raising thedriver’s side first, then the passenger’s side.
2. Remove the cover (A), by squeezing the two tabs and pulling it straight out.
3. Press and hold the tab (B), and slide the wiper blade (C) toward the tab until it releases from the
wiper arm (D).
4. Find the side of the blade labeled ‘‘LOCK’’ (A), then pull back the end of the blade and slide out the old
rubber (B).
5. Install a new rubber in the r everse order of removal.
6. Install the wiper blades onto the windshield wiper arms in the reverse order of removal.
7. Test by turning on the wipers. If the blades slip, turn off the wipers and seat the attachments more
firmly. 1. Lift the wiper arm off the windshield, raising the
driver’s side first, then the passenger’s side.
2. Pull up the tab (A), and slide the wiper blade (B) until it releases from the wiper arm (C).
3. Find the blade labeled ‘‘SET’’ (A), then release the blade from it.
4. Pull back the end of the blade and slide out the old rubber (B).
5. Install a new rubber in the r everse order of removal.
6. Install the wiper blades onto the windshield wiper arms in the reverse order of removal.
7. Test by turning on the wipers. If the blades slip, turn off the wipers and seat the attachments more
firmly.
08/08/21 14:28:50 61SNR030_220_0237
ProCarManuals.com
DYNOMITE -2009-

¦§
¦§

(#'
") Wiper arms stop position
Washer nozzle position
22-236Wipers/Washers
Wiper Arm/Nozzle Adjustment
C
B
A
d
e
b a
c
e
1. When the wiper arms stop at the automatic stop position, confirm that they are at the standard position.
a: Position at about 23 mm (0.9 in.) from the top of cowl cover (A)
b: Position at about 96 mm (3.8 in.) 114 mm (4.5 in.) from the top of cowl cover (A) : ’08-09 models
2. When you turn on the washers, confirm 50 % or more of the washer fluid lands within the spray area. If the spray area is not within the standard positions, adjust the nozzles.
c: Position at about 192 mm (7.6 in.) from the top of the black ceramic area (B) at the lower windshield
d: Position at about 192 mm (7.6 in.) from the top of the black ceramic area (B) at the lower windshield
e: Position at about 250 mm (9.8 in.) from the windshield center line (C)
08/08/21 14:28:50 61SNR030_220_0238
ProCarManuals.com
DYNOMITE -2009-