check oil ACURA CSX 2006 Service Repair Manual

µµµµ µ •••
¶
µ
µµ
µµ
µµ
(#'#)
Engine Electrical
Engine Assembly
Item Measurement QualificationStandard or New Service Limit
Item Measurement Qualification Standard or New
2-2Standards and Service Limits
Ignition coil Rated voltage
12 V
Firingorder 1342
Spark plug Type (K20Z2) DENSO: SKJ20DR-M11
Type (K20Z3) DENSO: SK22PR-M11S
Gap 1.0 1.1 mm (0.039 0.043 in.)
Ignition timing At idle Check the mark M/T (in neutral),
A/T (in N or P)82°BTDC
Drive belt Tension Auto-tensioner
Alternator Output At 13.5 V and
normal engine
temperature 105 A
Coil (rotor) resistance 20 °C (68 °F) 3.2 4.0
Slip ring O.D. 14.4 mm (0.57 in.)14.0 mm (0.55 in.)
Brush length 10.5 mm (0.41 in.)1.5 mm (0.06 in.)
Brush spring tension 3.2 N (0.33 kgf, 0.7 lbf)
Starter Output 1.6 kW
Commutator mica depth 0.40 0.50 mm (0.016 0.020 in.) 0.15 mm (0.006 in.)
Commutator runout 0.02 mm (0.0008 in.) max.0.05 mm (0.002 in.)
Commutator O.D. 28.0 28.1 mm (1.102 1.106 in.) 27.5 mm (1.083 in.)
Brush length 11.1 11.5 mm (0.44 0.45 in.)4.3 mm (0.17 in.)
Compression Pressure Check the engine with the starter
cranking Minimum 930 kPa (9.5 kgf/cm , 135 psi)
Maximum
variation
200 kPa (2.0 kgf/cm , 28 psi)
2
2
red
08/08/21 14:07:14 61SNR030_020_0002
ProCarManuals.com
DYNOMITE -2009-

Automatic Transmission and A/T Differential (cont’d)
ItemMeasurement Qualification Standard or New
Wire Diameter O.D. Free Length No. of Coils
2-16 Standards and Service Limits
Main valve body
spring (see page
14-303)
Shift valve A spring 0.8 mm
(0.031 in.)5.6 mm
(0.220 in.)28.1 mm
(1.106 in.) 15.9
Shift valve B spring 0.8 mm (0.031 in.)5.6 mm
(0.220 in.)28.1 mm
(1.106 in.) 15.9
Shift valve C spring 0.8 mm (0.031 in.)5.6 mm
(0.220 in.)28.1 mm
(1.106 in.) 15.9
Relief valve spring 1.0 mm (0.039 in.)9.6 mm
(0.378 in.)34.1 mm
(1.343 in.) 10.2
Lock-up control valve spring 0.65 mm (0.026 in.)7.1 mm
(0.280 in.)23.1 mm
(0.909 in.) 12.7
Cooler check valve spring 0.85 mm (0.033 in.)6.6 mm
(0.260 in.)27.0 mm
(1.063 in.) 11.3
Servo control valve spring 0.7 mm (0.028 in.)6.6 mm
(0.260 in.)35.7 mm
(1.406 in.) 17.2
Shift valve E spring 0.8 mm (0.031 in.)5.6 mm
(0.220 in.)28.1 mm
(1.106 in.) 15.9
Regulator valve
body spring
(see page
14-305) Stator reaction spring 4.5 mm
(0.177 in.)35.4 mm
(1.394 in.)30.3 mm
(1.193 in.) 1.92
Regulator valve spring A 1.9 mm (0.075 in.)14.7 mm
(0.579 in.)80.6 mm
(3.173 in.) 16.1
Regulator valve spring B 1.6 mm (0.063 in.)9.2 mm
(0.362 in.)44.0 mm
(1.732 in.) 12.5
Torque converter check valve spring 1.2 mm (0.047 in.)8.6 mm
(0.339 in.)33.8 mm
(1.331 in.) 12.2
Lock-up shift valve spring 1.0 mm (0.039 in.)6.6 mm
(0.260 in.)35.5 mm
(1.398 in.) 18.2
3rd accumulator spring 2.5 mm (0.098 in.)14.6 mm
(0.575 in.)29.9 mm
(1.177 in.) 4.9
1st accumulator spring A 2.4 mm (0.094 in.)18.6 mm
(0.732 in.)49.0 mm
(1.929 in.) 7.1
1st accumulator spring B 2.3 mm (0.091 in.)12.2 mm
(0.480 in.)31.5 mm
(1.240 in.) 6.6
Servo body
spring (see page
14-306) Shift valve D spring 0.8 mm
(0.031 in.)5.6 mm
(0.220 in.)28.1 mm
(1.106 in.) 15.9
4th accumulator spring B 2.3 mm (0.091 in.)12.2 mm
(0.480 in.)31.5 mm
(1.240 in.) 6.6
4th accumulator spring A 2.4 mm (0.094 in.)18.6 mm
(0.732 in.)49.0 mm
(1.929 in.) 7.1
2nd accumulator spring B 2.0 mm (0.079 in.)10.6 mm
(0.417 in.)34.0 mm
(1.339 in.) 8.0
2nd accumulator spring A 2.2 mm (0.087 in.)16.6 mm
(0.654 in.)48.2 mm
(1.898 in.) 8.5
5th accumulator spring 2.5 mm (0.098 in.)14.6 mm
(0.575 in.)29.9 mm
(1.177 in.) 4.9
08/08/21 14:07:17 61SNR030_020_0016
ProCarManuals.com
DYNOMITE -2009-

(#')Symbol Maintenance Main Items
3-7
Maintenance Main Items
If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every
year.
NOTE:


 Replace the brake fluid every 3 years independent of the maintenance messages in the information display.
Inspect idle speed every 160,000 miles (256,000 km).
Adjust the valves during services A, B, 1, 2 or 3, only if they are noisy.

















A Replace engine oil (see page 8-10).
Engine oil capacity without oil filter:
K20Z2: 4.0 L (4.2 US qt)
K20Z3: 4.2 L (4.4 US qt)
B Replace engine oil and oil filter (see page 8-11). Engine oil capacity with oil filter:
K20Z2: 4.2 L (4.4 US qt)
K20Z3: 4.4 L (4.6 US qt)
Check front and rear brakes (see page 19-3). Check pad and disc for wear (thickness), damage, and cracks.
Check calipers for damage, leaks, and tightness of mounting bolts.
Check parking brake adjustment (see page 19-7). Check the number of clicks (8 to 10) when the parking brake lever is pulled with 196 N (20 kgf,
44 lbf) of force.
Inspect tie-rod ends, steering gearbox, and gearbox boots (see page 17-5). Check steering linkage.
Check boots for damage and leaking grease.
Check fluid lines for damage and leaks.
Inspect suspension components (see page 18-3). Check bolts for tightness.
Check condition of ball joint boots for deterioration and damage.
Inspect driveshaft boots (see page 16-4). Check boots for cracks and boot bands for tightness.
Inspect brake hoses and lines including VSA lines (see page 19-37). Check the master cylinder and VSA modulator-control unit for damage or leakage.
Inspect all fluid levels and condition of fluids. Engine coolant (see page 10-7)
Automatic transmission fluid (ATF-Z1) (see page 14-231)
Manual transmission fluid (MTF)
5M/T (see page 13-5), 6M/T (see page 13-82)
Clutch fluid (see page 12-7)
Brake fluid (see page 19-9)
Windshield washer fluid (see page 22-234)
Inspect exhaust system: K20Z2 (see page 9-13), K20Z3 (see page 9-14)
Check catalytic converter heat shields, exhaust pipes, and muffler for damage, leaks, and tightness.
Inspect fuel lines (see page 11-326) and connections (see page 11-328). Check for loose connections, cra cks, and deterioration; retighten loose connections and replace
damaged parts.
NOTE: According to state and federal regulations, failure to do the maintenance items marked with an asterisk ( ) will
not void the client’s emissions warranties. However, Acura recommends that all maintenance services be done at the
recommended interval, to ensure long-term reliability.
08/08/21 14:08:32 61SNR030_030_0007
ProCarManuals.com
DYNOMITE -2009-




µµ
Commutator Mica Depth
Standard (New): 0.40 0.50 mm (0.016 0.020 in.)
Service Limit: 0.15 mm (0.006 in.)
4-15
A
B
C
D C
B
A
A
B
C
7. Check the mica depth (A). If the mica is too high (B),
undercut the mica with a ha cksaw blade to the
proper depth. Cut away all the mica (C) between
the commutator segments. The undercut should
not be too shallow, too narrow, or V-shaped (D).
8. Use an ohmmeter to check for continuity between the segments of the commutator. If there is an
open circuit between any of the segments, replace
the armature. 9. Place the armature (A) on an armature tester (B).
Hold a hacksaw blade (C) on the armature core. If
the blade is attracted to the core or vibrates while
the core is turned, the armature is shorted. Replace
the armature.
10. Use an ohmmeter check for continuity between the commutator (A) and the armature coil core (B), and
the between the commutator and the armature
shaft (C). If there is continuity, replace the armature.
(cont’d)
08/08/21 14:09:27 61SNR030_040_0016
ProCarManuals.com
DYNOMITE -2009-

Î
 Î

5-23
B
A
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft) A
B A
B
C
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
C
56. Install the ECM/PCM (A), then install the ECM/PCM
cover (B).
57. Connect the battery cables (A) to the under-hood fuse/relay box.
58. Install the harness clamp (B). 59. Install the pipe (A).
60. Connect the connector (B), and install the harness
clamps (C).
61. Install the under cowl-panel (see step 4 on page 20-164).
62. Install the air cleaner assembly (see page 11-345).
63. Install the front wheels.
64. Do the battery installation procedure (see page 22-69).
65. Inspect for fuel leaks. Turn the ignition switch to ON (II) (do not operate the starter) so the fuel pump
runs for about 2 seconds and pressurizes the fuel
line. Repeat this operation three times, then check
for fuel leakage at any point in the fuel line.
66. Refill the engine with engine oil (see step 4 on page 8-10).
(cont’d)
08/08/21 14:21:01 61SNR030_050_0023
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
 M/T model
A/T model
5-245-24
Engine Assembly
Engine Installation (cont’d)
Side Engine Mount Replacement
67. Refill the transmission with fluid:
 Manual transmission (see step 3 on page 13-5)
 Automatic transmission (see step 3 on page14-232)
68. A/T model: Move the shift lever to each gear, and verify that the A/T gear position indicator follows
the transmission range switch.
69. M/T model: Check that the transmission shifts into gear smoothly.
70. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
71. Do the ECM/PCM reset procedure (see page 11-4).
72. Do the crankshaft position (CKP) pattern clear/CKP pattern learn procedure (see page 11-4).
73. Inspect the idle speed (see page 11-309).
74. Inspect the ignition timing (see page 4-20).
75. Check the wheel alignment (see page 18-5). 1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:01 61SNR030_050_0024
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
 M/T model
A/T model
5-245-24
Engine Assembly
Engine Installation (cont’d)
Side Engine Mount Replacement
67. Refill the transmission with fluid:
 Manual transmission (see step 3 on page 13-5)
 Automatic transmission (see step 3 on page14-232)
68. A/T model: Move the shift lever to each gear, and verify that the A/T gear position indicator follows
the transmission range switch.
69. M/T model: Check that the transmission shifts into gear smoothly.
70. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
71. Do the ECM/PCM reset procedure (see page 11-4).
72. Do the crankshaft position (CKP) pattern clear/CKP pattern learn procedure (see page 11-4).
73. Inspect the idle speed (see page 11-309).
74. Inspect the ignition timing (see page 4-20).
75. Check the wheel alignment (see page 18-5). 1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:01 61SNR030_050_0024
ProCarManuals.com
DYNOMITE -2009-


(#'
")Compression Pressure:
Above 930 kPa (9.5 kgf/cm , 135 psi)
Maximum Variation:
Within 200 kPa (2.0 kgf/cm , 28 psi)
2
2
6-7
Engine Compression Inspection
NOTE: After this inspection, you must reset the engine
control module (ECM)/powertrain control module
(PCM), otherwise the ECM/PCM will continue to stop
the fuel injectors from operating. 1. Warm up the engine to normal operating temperature (cooling fan comes on).
2. Turn the ignition switch to LOCK (0).
3. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC) (see step 2 on page 11-3).
4. Turn the ignition switch to ON (II).
5. Make sure the HDS communicates with the vehicle and the ECM/PCM. If it does not communicate,
troubleshoot the DLC circuit (see page 11- 204).
6. Select ALL INJECTORS STOP in the PGM-FI, INSPECTION menu with the HDS.
7. Turn the ignition switch to LOCK (0).
8. Remove the four ignition coils (see page 4-21).
9. Remove the four spark plugs.
10. Attach the compression gauge to a spark plug hole. 11. Step on the accelerator pedal to open the throttle
fully, then crank the engine with the starter motor,
and measure the compression.
12. Measure the compression on the remaining cylinders.
13. If the compression is not within specifications, check the following items, then remeasure the
compression.
 Incorrect valve clearance
 Confirmation of cam timing
 Damaged or worn cam lobes
 Damaged or worn valves and seats
 Damaged cylinder head gasket
 Damaged or worn piston rings
 Damaged or worn piston and cylinder bore
14. Remove the compression gauge from the spark plug hole.
15. Install the four spark plugs.
16. Install the four ignition coils (see page 4-21).
17. Select the ECM/PCM reset (see page 11-4) in the PGM-FI INSPECTION menu to cancel ALL
INJECTORS STOP with the HDS.
08/08/21 14:26:27 61SNR030_060_0007
ProCarManuals.com
DYNOMITE -2009-



Specified Torque
Intake:
7x0.75mm
20 N·m (2.0 kgf·m, 14 lbf·ft)
Apply new engine oil to the nut threads.
Exhaust:
7x0.75mm
14 N·m (1.4 kgf·m, 10 lbf·ft)
Apply new engine oil to the nut threads.
6-13
07MAA-PR70110
07MAA-PR70120
5. If you feel too much or too little drag, loosen the locknut with the locknut wrench and the adjuster,
andturntheadjustingscrewuntilthedragonthe
feeler gauge is correct.
6. Tighten the locknut to the specified torque, and recheck the clearance. Repeat the adjustment if
necessary. 7. Rotate the crankshaft 180 ° clockwise (camshaft
pulley turns 90 °).
8. Check and, if necessary, adjust the valve clearance on the No. 3 cylinder.
9. Rotate the crankshaft 180 ° clockwise (camshaft pulley turns 90 °).
10. Check and, if necessary, adjust the valve clearance on the No. 4 cylinder.
(cont’d)
08/08/21 14:26:30 61SNR030_060_0013
ProCarManuals.com
DYNOMITE -2009-




µµ
µµ
Valve Clearance
Intake: 0.21 0.25 mm (0.008 0.010 in.)
Exhaust: 0.25 0.29 mm (0.010 0.011 in.)
Specified Torque
7x0.75mm
20 N·m (2.0 kgf·m, 14 lbf·ft)
Apply new engine oil to the nut threads.
6-15
No. 1No. 2 No. 3 No. 4
No. 1 No. 2
No. 3 No. 4
EXHAUST
INTAKE
AB 07MAA-PR70110
07MAA-PR70120
3. Select the correct feeler gauge for the valve clearance you are going to check.
4. Insert the feeler gauge (A) between the adjusting screw (B) and the end of the valve stem, then slide
it back and forth, you should feel a slight amount of
drag. 5. If you feel too much or too little drag, loosen the
locknut with the locknut wrench and the adjuster,
andturntheadjustingscrewuntilthedragonthe
feeler gauge is correct.
6. Tighten the locknut to specified torque, and recheck the clearance. Repeat the adjustment if necessary.
7. Rotate the crankshaft 180 ° clockwise (camshaft pulley turns 90 °).
8. Check and, if necessary, adjust the valve clearance on the No. 3 cylinder.
(cont’d)
08/08/21 14:26:31 61SNR030_060_0015
ProCarManuals.com
DYNOMITE -2009-