ACURA CSX 2006 Service Repair Manual

Î
Î

Î

Unit Check (Quick Check)Display
Radio
23-305
ReturnReturn
ReturnSelect Check Units Display Radio Hard Key
Yaw Sensor DVD
GPS
ECU Info.
Rear Camera
PC Card Info Aircon
HFL
XM Display
OK
OK
Connection
Version
040423
Radio OK
Connection
OK
0.2dBuV
Electric Field Intensity
7150
CD Mech. Version
Some of the tests and screens that are displayed under
the Unit Check are different from the more detailed
checks listed in other areas of this service manual.
To start the test, select the item you want to check.
Display
Radio
GPS
ECUInfo.
 Rear Camera
 PC Card Info.
 Hard Key
 Yaw Sensor
DVD
 Aircon
HFL
XM This performs additional checks on the communication
bus between the navi CPU and the navigation display.
In addition, this test checks the internal electronic
functions
If the connection is NG, replace the navigation unit.
 Connection verifies internal communications.
 Version represents the software version for the display.
This diagnostic screen checks the internals of the radio
(AM and FM) and CD player. If NG, replace the
navigation unit.
(cont’d)
08/08/21 14:16:41 61SNR030_230_0308
ProCarManuals.com
DYNOMITE -2009-

Î
Î

GPS ECU Info.
23-306 Navigation System
System Diagnostic Mode (cont’d)
Return
Information
D-RAMCheckMem Clear
(2007.08.31 15:31:28)
Antenna OK
OK
GPS
ECU Info.Return
Receiver in Navi ECU
V-RAM OK
DVD Lid Close
Program Flash
1.64.00
Program on DVD 1.64.0000
DVD Version 4.62
Serial No. xxxxxxxxxx
Model SNRX D-RAM OK
If GPS indicates NG (ANT), then check the entire GPS
antenna wire from the navigation unit to the GPS
antenna. If the wire is crushed or damaged, try a
known-good antenna. If the diagnostic reads OK,
replace the original GPS antenna. If the diagnostic still
reads NG (ANT), replace the navigation unit.
Select information to see the GPS satellite details.
This screen looks for problems in the navigation unit.
When you initiate this diagnosis, the navigation unit
may freeze or delay up to a minute while the diagnosis
runs.
NOTE: Do not try to end this diagnostic by pressing OK
or Mem clear before it finishes, otherwise the system
may reboot.
 If V-RAM or D-RAM is NG, replace the navigation unit.
 DVD lid displays the state of DVD Lid of navigation unit.
 Program Flash: Displays the version of the navi software in memory.
 Program on DVD: If displayed, this value represents the version of the navigation software on the navi
DVD.
 DVD version represents the database version on the DVD. You can find this information in either the Setup
Screen Version, or in the Diagnostic Screen Version.
 Serial No. should be the same as the serial number found on the underside of the navigation unit. You
need this number to obtain the security code from the
Interactive Network (iN) system.
 The Mem Clr is for factory use and should not be used unless instructed by the factory.
Selecting this will clear the customer’s settings,
personal information, GPS orbital data, and anything
else stored in memory.
08/08/21 14:16:41 61SNR030_230_0309
ProCarManuals.com
DYNOMITE -2009-

ÎÎ
Î
Rear Camera (Optional) PC Card info.
23-307
Return
Return
ReturnRear Camera
Connection NG PC Card Information
PC Card is not inserted.
PC Card Information
Manufacturer xxxxxx
Product Name xxxxxx
Files
 If the optional rearview camera is connected, itappears as OK.
 It displays OFF when the optional rearview camera is not connected. There is no PC Card in the PC slot, and the screen
should display, PC Card is not inserted.
NOTE: Do not insert any card or object into the slot.
If the factory provides a PC card and instructs you to
insert it, the screen displays the Manufacturer, and
Product Name as shown in the following screen.
Follow the instructions provided by the factry to
complete the test.
(cont’d)
08/08/21 14:16:41 61SNR030_230_0310
ProCarManuals.com
DYNOMITE -2009-

´µ ´µ
Î
Î Î
Î
Î
´
µ
´
µ
´µ
Hard Key
Yaw Sensor DVD
Aircon
HFL
23-308Navigation System
System Diagnostic Mode (cont’d)
Hard KeyReturn
Return
ZOOM OUT ZOOM IN
CANCEL SET UP MAP
MENU INFO
MODE CH
CH
VOL
VOL
FF
REW
RPT RDM
SEEK UP SCAN
AUDIO
CD/AUX
AM/FMSKIP
SKIP
SEEK DOWN Keep Pushing to Return.
Yaw Sensor
Zero Point Output OK OK
Output Value x.xxxV
Current Offset x.xxxV
Temperature in ECU xx°C
Return
Return
ReturnDVD
Error Detail -
Version 20050404
Maker ID 0x01
Navi Platform 0x01
Connection OK Aircon
HFL
Connection OK
This diagnostic screen checks the status of each of the
hard buttons surrounding the navigation display. When
you press each hard button, the corresponding item on
the screen should flash blue. Touch the return key, or
press and hold the joystick to exit.
NOTE: It is normal for the VOL ( , ) CH ( , ) and
MODEbuttontobeinactive.
This screen gives a quick test of the yaw sensor
functionality based on the two voltages Sensor and
Offset. For more information see the Yaw Rate
Diagnostic. This diagnostic tests the navigation DVD reader.
This diagnostic tests the climate bus connection (AC-SI
and AC-SO) between the navigation unit and climate
control unit. Make sure the engine is running for this
test.
 This checks the 4 wire communication bus between the HFL and the navigation.
 When connection is shown with NG, check the connection between the navigation unit and the
HandsFreeLink control unit.
08/08/21 14:16:42 61SNR030_230_0311
ProCarManuals.com
DYNOMITE -2009-

ÎÎ
XM
Functional Setup
23-309
Return
ReturnXM
Connection OK
Demo Mode
Save Users Memory Functional Setup
Mic Level
 This checks the GA-NET Bus line to the XM receiver.
 When connection is shown with NG, check theconnection between the XM receiver and the
navigation unit. Select the item you want to check.
 Save Users Memory
 Demo Mode
 Mic Level
(cont’d)
08/08/21 14:16:42 61SNR030_230_0312
ProCarManuals.com
DYNOMITE -2009-

ÎÎ
Î


Save Users Memory
23-310Navigation System
System Diagnostic Mode (cont’d)
Return
EXPORT
IMPORT
Save Users Memory
Return
Yes No
Return
Yes NoSave Users Memory Export User Data
Save Users Memory Import User Data
When replacing the navigation unit, this function allows
the dealer to transfer the client’s personal data to the
new navigation unit. The transferred information
includes their Setup settings, and personal addresses.
The dealer inserts a PC card to the navigation unit, and
then selects the Save Users Memory function. The two
functions in this diagnostic screen are EXPORT and
IMPORT. EXPORT saves the client’s data to the PC card,
andIMPORTmovesthePCcardfilestothenew
navigation unit.
Before starting this function, see the PC Card FAQs for
information regarding PC cards, and how to use this
function. 1. Select EXPORT button to move the client’s data
from the original navigation unit to the PC card.
Select YES on the Export User Data Confirmation
screen. The process takes only a couple of seconds.
The system stores two files on the card.
NOTE: If the EXPORT button is grayed out, check
the PC card’s edge connector, and the pins inside
the navigation unit (with a flashlight) for damage.
2. After installing the client’s original DVD in the new navigation unit, allow the system to boot up. Insert
the PC card in the new navigation unit and enter the
Save Users Memory in the navigation system
diagnostic mode.
3. Select IMPORT button to move the two files stored by the Export process from the PC card to the new
navigation unit. Select YES on the Import User Data
Confirmation screen. When the transfer is finished
(a few seconds) the system automatically reboots.
After the system reboots, remove the PC card from
the PC slot.
NOTE: If the IMPORT button is grayed out, check if
the Model and the Program Flash shown on the
Version screen are the same.
08/08/21 14:16:43 61SNR030_230_0313
ProCarManuals.com
DYNOMITE -2009-

ÎÎ
Demo ModeMic Level
23-311
ReturnDemo Mode
OFF
Demo
Speed Rate 150 ms ON OFF
Mic LevelReturn
Mic Level
Steering Switch
This screen is for factory use only, and should always
be set to OFF. Occasionally the DEMO setting is turned
ON when vehicles are being used at Auto Shows or
similar events. Turning this feature on, allows the
navigation system to automatically follow a route to a
destination when the vehicle is stationary. The Speed
changes the speed of the demo mode. This diagnostic allows you to independently test the
microphone and the navigation TALK and BACK
buttons. They are used to activate the voice control
system. The microphone is located near the map light
in the roof console. It is directional, and works only with
the voice coming from the driver’s seat.
 Press the navigation TALK button on the steering wheel, wait unit you hear a beep, and in a normal
voice say ‘‘testing’’. The TALK indicator on the screen
should momentarily turn green, and the text Now
Recording... should appear in yellow. If the talk
indicator shown on the screen does not briefly turn
green, check the wiring from the steering wheel
navigation TALK button to the navigation unit. If there
is no Mic Level movement when you speak, then you
should check the wires running from the microphone
in the roof console to the HandsFreeLink control unit
and the navigation unit. If the wires are OK, the
microphone must be faulty; replace the microphone
located in roof console (see page 23-358).
 PressthenavigationBACKbuttononthesteering wheel. This should cause the Cancel indicator on the
screen to momentarily turn green. If it does not
briefly turn green, check the wiring from the steering
wheel navigation BACK button to the navigation unit.
(cont’d)
08/08/21 14:16:43 61SNR030_230_0314
ProCarManuals.com
DYNOMITE -2009-

Î
¡
¡
GPS Information
23-312 Navigation System
System Diagnostic Mode (cont’d)
ReturnGPS Information
Number of Satellites
Current Position Latitude
Elevation Longitude
xxxx.xx.xx xx:xx:xx N xx°xx’xx
Exxx°xx’xx
xx feet
In Use
Search
This screen shows the current status of GPS reception.
The circular diagram shows the current location of the
GPS satellites (yellow numbers) as they would appear
in the sky. The outer circle represents the horizon
(0 degrees elevation). The middle and inner circles
represents 30 and 60 degrees respectively. The very
center of the diagram (90 degrees elevation) is directly
overhead. Nearby obstructions, like tall buildings will
block satellites in that direction. That is why it is
necessary to be in an open area to effectively
troubleshoot GPS reception issues. The sate llite
numbers shown on the diagram correspond to the PRN
number in the GPS Details screen. There are always at
least 24 active GPS satellites in orbit. Because satellites
fail, and have to be removed from service, spares are
always parked in orbit, ready to be activated. This is
why the PRN (satellite ID number) can be greater than
24.
NOTE: When you use this screen for troubleshooting,
park the vehicle outside, away from buildings, tall trees,
and high-tension wires for at least 10 minutes with the
engine running.  The Number of Satellites box shows the number of
acquired satellites (maximum of 12). It should contain
three or more icons. If not troubleshoot for GPS icon
is white or not shown (see page 23-341).
 The Current Position shows latitude, longitude, and elevation (in feet). If there are less than four satellites,
the elevation can be grossly inaccurate.
 The Date/Time field shows the current date, and also a time that includes daylight savings and other
offsets entered by the customer in Setup screen 2
Adjust Time Zone/Clock.
NOTE: Pressing the map/guide button displays the
satellite number on each circle.
08/08/21 14:16:43 61SNR030_230_0315
ProCarManuals.com
DYNOMITE -2009-

µ
Ú Ü
Î
GPS Detail
Column Description Problem indication
23-313
GPS Detail
PRN
3D ST AZI EL ACC
C/N
1/2
xx
xx
xxxxx xxx
xx
xx
xx
xxxxx xxx
xx
xx
xx
xxxxx xxx
xx
xx
xx xxx xx xxx
xx
xx
xx
xxxxx xxx
xx
xx
xx
xxxxx xxx
xxReturn
TS:xx
AS:xxHDop:xx.x Date:xxxx.xx.xx
VDop:xx.x Speed:x.xKm/h
Direction: x° Time:xx:xx:xx
By pressing and holding the MENU button for
2 seconds, a GPS Detail screen appears. This screen
displays real time incoming satellite positional data
when the vehicle is outside in the open. The
information shown on this screen is for factory use.
NOTE: The data shown in an example only.
 The box TS/AS and H Dop/V Dop is for factory use.
 The Speed and Direction information is updated in real time when driving.
 The Date/Time Information is the same as in Setup screen 2 Adjust Time Zone/Clock.
 If the 3D icon is shown above the yellow dots, this implies that at least four satellites are available for
map positioning, and the GPS indicator on the map
screen will be green. See the Global Positioning
System detailed explanation in the System
Description.
 If the row of data in the table below begins with a yellow dot, the AZI and EL fields can be used to locate
each satellite on the circular GPS diagram (see prior
screen). NOTE: The table of values define the terms at the top of
the columns in the GPS Detail screen.
3D Active satellites (Yellow Dot) If 3D or 2D is
missing when the
vehicle is parked
outside, follow
GPS icon is white
or not shown
troubleshooting
(see page 23-341).
PRN The satellite ID number
ST The status: 0 = cannot view
or searching,
2 = acquiring If all 0, then, follow
GPS icon is white
or not shown
troubleshooting
(see page 23-341).
AZI Azimuth, the angle (0 360) clockwise
from north
EL Elevation from the horizon (90 deg is
overhead)
C/N N/A Normal signal is 49-52, no signal:
27-33
ACC N/A
1/2 or
2/2 Shows view of all
satellites in two
screen views 1/2 or
2/2
(cont’d)
08/08/21 14:16:44 61SNR030_230_0316
ProCarManuals.com
DYNOMITE -2009-

´µµ Î
Yaw Rate
Example: Vehicle stopped
Normal Abnormal
Example: Vehicle turning
Normal Abnormal
23-314Navigation System
System Diagnostic Mode (cont’d)
ReturnYaw Rate
Sensor Offset
CCW Factor
CW Factor x.xxxV
x.xxxV
x.x%
x.x% Tuning
This diagnostic checks the yaw rate sensor in the
navigation unit. This device detects when the vehicle
turns, and repositions the vehicle position icon on the
map screen. For more detailed information, see the yaw
rate sensor theory of operation under System
Description (see page 23-283).
 Sensor indicates the voltage output from the yaw rate sensor. It should indicate about 2.500 V when the
vehicle is stopped.
 Offset is the reference voltage or standard within the yaw rate sensor. It also should indicate about 2.500 V
when the vehicle is stopped.
 A sensor output voltage LOWER than the Offset voltage indicates that the vehicle is turning to the
right.
A sensor output voltage HIGHER than the Offset
voltage indicates that the vehicle is turning to the left.
 The yaw rate offset, and sensor should both indicate about 2.500 V when the vehicle is stopped. If either
reads zero, or 5.000 V, replace the navigation unit.
 The yaw rate offset and sensor should be within / 0.01 V of each other when the vehicle is stopped.
The sensor value should change relative to the offset
as the vehicle turns while driving. If not, replace the
navigation unit.
Offset 2.526 V Offset 2.526 V
Sensor 2.516 2.536 V Sensor 2.623 V
Offset 2.526 V Offset 2.526 V
Sensor 2.678 V (left turn)
2.478 V
(right turn) Sensor 2.623 V
(no change on
turns)  Sensitivity study represents the status of the internal
tuning function. At initialization, this value starts at 6
and increases to 10 as the internal correction values
become more accurate.
 The settings CCW Cal Factor, CW Cal Factor, and Set are for factory use only. THIS SHOULD NEVER BE
ADJUSTED.
 For detailed analysis of the yaw rate select tuning.
08/08/21 14:16:44 61SNR030_230_0317
ProCarManuals.com
DYNOMITE -2009-