ACURA CSX 2006 Service Repair Manual



(#'
 )
Removal Installation
24-210SRS
Front Impact Sensor Replacement
A
B
C A
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
C
B
1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the front inner fender (see page 20-171).
3. Remove the washer reservoir (see page 22-234).
4. Remove the intake air resonator:  K20Z2 engine (see page 11-346)
 K20Z3 engine (see page 11-347)
5. Disconnect the engine compartment wire harness 2P connector (A). Using a TORX T30 bit, remove the
TORX bolt (B), then remove the front impact
sensor (C). Discard the bolt. 1. Install the front impact sensor with a new TORX
bolt (A), then connect the engine compartment wire
harness 2P connector (B) to the front impact sensor
(C).
2. Do the battery terminal reconnection procedure (see page 22-68).
3. Clear any DTCs (see page 24-23).
4. Confirm proper operation: Turn the ignition switch to ON (II); the SRS indicator should come on for
about 6 seconds and then go off.
5. Reinstall all removed parts.
Replace.
08/08/21 14:02:04 61SNR030_240_0210
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#' )
Removal Installation
24-211
Driver’s Seat Position Sensor Replacement
A
B C
C
A
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
B
NOTE:  Removal of the driver’s seat position sensor must be done according Precautions and Procedures
(see page 24-13).
 Do not turn the ignition switch to ON (II), and do not connect the battery cable while removing the driver’s
seat position sensor.
1. Do the battery terminal disconnection procedure (see page 22-68), then wait at least 3 minutes
before starting work.
2. Remove the driver’s seat assembly (see page 20-118).
3. Disconnect the seat position sensor harness 2P connector (A) from the driver’s seat position sensor
(B).
4. Using a TORX T30 bit, remove the TORX bolt (C), then remove the driver’s seat position sensor. NOTE:
 Be sure to install the harness so it does not pinched or interfere with other parts.
 Do not turn the ignition switch to ON (II), and do not connect the battery cable while insta lling the driver’s
seat position sensor.
 After installing the driver’s seat position sensor, make sure it is clean. Keep it away from dust.
1. Install the driver’s seat position sensor with a new TORX bolt (A), then connect the seat position
sensor harness 2P connector (B) to the driver’s seat
position sensor (C).
2. Install the driver’s seat assembly (see page 20-118).
3. Do the battery terminal reconnection procedure (see page 22-68).
4. Clear any DTCs (see page 24-23).
5. Check the operation of the driver’s seat position sensor with the HDS (see page 24-29).
Replace.
08/08/21 14:02:11 61SNR030_240_0211
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
)
24-212SRS
Passenger’s Airbag Cutoff Indicator Illumination Bulb Test/Replacement
B
A
C
1. Remove the center panel: Navigation unit, with navigation system.– ’06-08 models (see page 23-256)
– ’09 model (see page 23-355)
 Audio unit, without navigation system. – ’06-08 models (see page 23-80)
– ’09 model (see page 23-155)
2. Remove the screws (A) and the passenger’s airbag cutoff indicator (B) from the center panel.
3. Check for continuity between the No. 2 and No. 3 terminals of the indicator. If there is no continuity,
replace the bulb (C).
4. Reinstall the parts in the reverse order of removal.
08/08/21 14:02:11 61SNR030_240_0212
ProCarManuals.com
DYNOMITE -2009-