torque ACURA CSX 2006 Service Owner's Manual



(#'
 )
 M/T model
A/T model
5-245-24
Engine Assembly
Engine Installation (cont’d)
Side Engine Mount Replacement
67. Refill the transmission with fluid:
 Manual transmission (see step 3 on page 13-5)
 Automatic transmission (see step 3 on page14-232)
68. A/T model: Move the shift lever to each gear, and verify that the A/T gear position indicator follows
the transmission range switch.
69. M/T model: Check that the transmission shifts into gear smoothly.
70. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
71. Do the ECM/PCM reset procedure (see page 11-4).
72. Do the crankshaft position (CKP) pattern clear/CKP pattern learn procedure (see page 11-4).
73. Inspect the idle speed (see page 11-309).
74. Inspect the ignition timing (see page 4-20).
75. Check the wheel alignment (see page 18-5). 1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:01 61SNR030_050_0024
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
 M/T model
A/T model
5-245-24
Engine Assembly
Engine Installation (cont’d)
Side Engine Mount Replacement
67. Refill the transmission with fluid:
 Manual transmission (see step 3 on page 13-5)
 Automatic transmission (see step 3 on page14-232)
68. A/T model: Move the shift lever to each gear, and verify that the A/T gear position indicator follows
the transmission range switch.
69. M/T model: Check that the transmission shifts into gear smoothly.
70. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
71. Do the ECM/PCM reset procedure (see page 11-4).
72. Do the crankshaft position (CKP) pattern clear/CKP pattern learn procedure (see page 11-4).
73. Inspect the idle speed (see page 11-309).
74. Inspect the ignition timing (see page 4-20).
75. Check the wheel alignment (see page 18-5). 1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:01 61SNR030_050_0024
ProCarManuals.com
DYNOMITE -2009-




M/T model
A/T model
5-26 Engine Assembly
Side Engine Mount Replacement (cont’d)
A
A A
A
9. Loosen the transmission mounting bolt and nuts (A). 10. Raise the vehicle on the lift.
11. Remove the splash shield (see step 25 on page 5-5).
12. Loosen the lower torque rod mounting bolt (A).
13. M/T model: Loosen the front mount mounting
bolt (A).
08/08/21 14:21:03 61SNR030_050_0026
ProCarManuals.com
DYNOMITE -2009-






M/T model
A/T model
5-28Engine Assembly
Side Engine Mount Replacement (cont’d)
14x1.5mm
93 N·m
(9.5 kgf·m, 69 lbf·ft)
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
17. Raise the vehicle on the lift.
18. Tighten the lower torque rod mounting bolt.
19. Lower the vehicle on the lift.
20. Install the air cleaner assembly (see page 11-345). 21. Install the upper torque rod, then tighten the new
upper torque rod mounting bolts in the numbered
sequence shown.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:04 61SNR030_050_0028
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
5-295-29
Transmission Mount Replacement
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft) A
22. Raise the vehicle on the lift.
23. M/T model: Tighten the front mount mounting bolt.
24. Install the splash shield (see step 40 on page 5-20).1. Loosen the upper torque rod mounting bolt (A).
2. Remove the air cleaner assembly (see page 11-345).
3. Remove the engine control module (ECM)/
powertrain control module (PCM) cover, then
remove the three bolts securing the ECM/PCM (see
step 10 on page 5-4).
4. Remove the under hood fuse/relay box from the ECM/PCM bracket, then remove the ECM/PCM
bracket(seestep13onpage5-4).
(cont’d)
08/08/21 14:21:04 61SNR030_050_0029
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
5-295-29
Transmission Mount Replacement
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft) A
22. Raise the vehicle on the lift.
23. M/T model: Tighten the front mount mounting bolt.
24. Install the splash shield (see step 40 on page 5-20).1. Loosen the upper torque rod mounting bolt (A).
2. Remove the air cleaner assembly (see page 11-345).
3. Remove the engine control module (ECM)/
powertrain control module (PCM) cover, then
remove the three bolts securing the ECM/PCM (see
step 10 on page 5-4).
4. Remove the under hood fuse/relay box from the ECM/PCM bracket, then remove the ECM/PCM
bracket(seestep13onpage5-4).
(cont’d)
08/08/21 14:21:04 61SNR030_050_0029
ProCarManuals.com
DYNOMITE -2009-


Î
Î
M/T model
A/T model
5-30 Engine Assembly
Transmission Mount Replacement (cont’d)
A
A
D
12x1.25mm
74N·m(7.5kgf·m,54lbf·ft) D
12x1.25mm
74 N·m
(7.5 kgf·m,
54 lbf·ft)
C E
12x1.25mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)
6x1.0mm
10 N·m
(1.0 kgf·m,
7.2 lbf·ft)
B
D
12 x 1.25 mm
64 N·m
(6.5 kgf·m,
47 lbf·ft) D
12x1.25mm
64 N·m
(6.5 kgf·m,
47 lbf·ft)
C A
10 x 1.25 mm
38 N·m
(3.9 kgf·m, 28 lbf·ft)
E
12 x 1.25 mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)
5. Raise the vehicle on the lift.
6. Remove the splash shield (see step 25 on page 5-5).
7. Loosen the lower torque rod mounting bolt (A).
8. M/T model: Loosen the front mount mounting bolt (A).
9. Lower the vehicle on the lift. 10. A/T model: Remove the transmission mount
stiffener (A).
11. M/T model: Remove the ground cable (B).
12. Remove the transmission mount (C).
13. Install the transmission mount, and tighten the transmission mount mounting bolts (D).
14. A/T model: Install the transmission mount stiffener.
15. Loosely tighten the new transmission mounting bolt and nuts (E).
16. M/T model: Install the ground cables.
Replace.
Replace.
Replace.
Replace. Replace.
Replace.
08/08/21 14:21:05 61SNR030_050_0030
ProCarManuals.com
DYNOMITE -2009-




M/T model
A/T model
5-31
12x1.25mm
74 N·m
(7.5 kgf·m, 54 lbf·ft)
12x1.25mm
74 N·m
(7.5 kgf·m, 54 lbf·ft) 14x1.5mm
93 N·m
(9.5 kgf·m, 69 lbf·ft)
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
17. Tighten the transmission mounting bolt and nuts. 18. Raise the vehicle on the lift. 19. Tighten the lower torque rod mounting bolt.
20. Lower the vehicle on the lift.
21. Tighten the upper torque rod mounting bolt.
(cont’d)
08/08/21 14:21:06 61SNR030_050_0031
ProCarManuals.com
DYNOMITE -2009-




(#'
 )
5-325-32 Engine Assembly
Transmission Mount Replacement
(cont’d)
Lower Torque Rod Replacement
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft) A
A
22. Install the ECM/PCM bracket, then install the under- hood fuse/relay box to the ECM/PCM bracket (see
step 52 on page 5-22).
23. Install the ECM/PCM, then install the ECM/PCM cover (see step 56 on page 5-23)
24. Install the air cleaner assembly (see page 11-345).
25. Raise the vehicle on the lift.
26. M/T model: Tighten the front mount mounting bolt.
27. Install the splash shield (see step 40 on page 5-20). 1. Loosen the upper torque rod mounting bolt (A).
2. Raise the vehicle on the lift.
3. Remove the splash shield (see step 25 on page 5-5).
4. M/T model: Loosen the front mount mounting
bolt (A).
08/08/21 14:21:06 61SNR030_050_0032
ProCarManuals.com
DYNOMITE -2009-




(#'
 )
5-325-32 Engine Assembly
Transmission Mount Replacement
(cont’d)
Lower Torque Rod Replacement
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft) A
A
22. Install the ECM/PCM bracket, then install the under- hood fuse/relay box to the ECM/PCM bracket (see
step 52 on page 5-22).
23. Install the ECM/PCM, then install the ECM/PCM cover (see step 56 on page 5-23)
24. Install the air cleaner assembly (see page 11-345).
25. Raise the vehicle on the lift.
26. M/T model: Tighten the front mount mounting bolt.
27. Install the splash shield (see step 40 on page 5-20). 1. Loosen the upper torque rod mounting bolt (A).
2. Raise the vehicle on the lift.
3. Remove the splash shield (see step 25 on page 5-5).
4. M/T model: Loosen the front mount mounting
bolt (A).
08/08/21 14:21:06 61SNR030_050_0032
ProCarManuals.com
DYNOMITE -2009-