trunk ACURA CSX 2006 Service Owner's Manual




(#'

 )
Special Tool Required
20-156
Trunk Lid
Trunk Lid Torsion Bar Replacement
B
A
A
B
B
A
07AAF-SNAA100 A
A B
=Normal position
=Higher tension
Torsion bar assembly tool 07AAF-SNAA100
1. Remove the torsion bars (A) from the torsion bar center clip (B).
2. Put on gloves to protect your hands. Remove the torsion bars with the torsion bar assembly tool
from both trunk lid hinges. First remove the left
torsion bar (A), then remove the right torsion bar
(B). 3. Remove the torsion bar center clip (A) from the
body.
4. Install the torsion bar in the reverse order of removal, and note these items:
 The shapes of the left torsion bar (A) and the right torsion bar (B) are shown. Install the torsion
bars properly.
 Adjust the torsion bars forward or rearward with the torsion bar assembly tool.
 The torsion bars were installed at the factory in the normal position, as shown.
 Make sure the trunk lid opens properly and locks securely.
08/08/21 15:04:58 61SNR030_200_0158
ProCarManuals.com
DYNOMITE -2009-


(#'

 ) 
(#'

 )
20-15720-157
Trunk Lid Weatherstrip
Replacement Trunk Lid Cushion Replacement
A
B
C
D A
Front A
B C
C
A
1. Remove the trunk lid weatherstrip (A) by pulling it off.
2. Apply clear weatherstrip sealant (B) into the channel of the trunk lid weatherstrip all the way
around.
3. Locate the painted alignment mark (C or D) on the trunk lid weatherstrip. Align the painted mark in the
center of the trunk lid opening, and install the trunk
lid weatherstrip all the way around in the direction
shown. Make sure there are no wrinkles in the
weatherstrip.
4. Check for water leaks (see step 9 on page 20-29). NOTE: Put on gloves to protect your hands.
1. Remove the trunk lid trim (see page 20-82).
2. Detach the clips (A) by pushing it from the hole in the trunk lid (B), then remove the trunk lid cushion
(C). Take care not to scratch the trunk lid.
3. Install the cushion in the reverse order of removal.
08/08/21 15:04:58 61SNR030_200_0159
ProCarManuals.com
DYNOMITE -2009-


(#'
 ) 
(#'


 )
20-16820-168 Exterior Trim
Side Sill Protection Tape
Replacement
Rear License Trim Replacement
AB
C
D
E F
A
D Fastener Locations
: Clip, 4
A : Clip, 2 B
A BC
D
B AA
A
1. Slowly peel up the old side sill protection tape.
2. Clean the body bonding surface with a shop towel
dampened in isopropyl alcohol. After cleaning,
keep oil, grease, and water from getting on the
surface.
3. Peel the adhesive backing from the side sill protection tape.
4. Align the alignment marks (A) of the side sill protection tape (B) with the body line (C), and align
the alignment marks (D) of the application tape (E)
with the round body bulge (F), then press the side
sill protection tape into place. 1. Detach the clips (A, B), and on both sides of the rear
license trim (C), release the edge of the trim from
the inner taillight (D), then remove the trim. Take
care not to scratch the trunk lid.
2. Install the trim in the reverse order of removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips into place securely.
08/08/21 15:05:04 61SNR030_200_0170
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
For Some Models
20-169
Trunk Lid Spoiler Replacement
:Nut,2 :Bolt,2
Fastener Locations
6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft) B
C
B A
NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the trunk lid.
1. Open the trunk lid, and remove the nut and bolts from inside the trunk lid. 2. Close the trunk lid. While lifting the trunk lid spoiler
(A) up, disconnect the high mount brake light
terminals (B) from the spoiler subharness (C), then
remove the spoiler.
3. Install the spoiler in the reverse order of removal, and make sure the high mount brake light terminals
are plugged in properly.
08/08/21 15:05:05 61SNR030_200_0171
ProCarManuals.com
DYNOMITE -2009-


(#'


 )
20-170Exterior Trim
Emblem/Sticker Replacement
FRONT ’’A’’ EMBLEM
REAR ’’A’’ EMBLEM
CSX EMBLEM
FRONT GRILLE BASE REAR ’’A’’ EMBLEM
ADHESIVE
TAPE
TRUNK LIDCLIP
CSX EMBLEM
Edge of the trunk lid
20 (0.79) ACURA EMBLEM
SCREWS
33
(1.3) 24
(0.94)
55
(2.17)
Edge of the inner taillight
Edge of the trunk lid
ACURA EMBLEM TYPE-S EMBLEM
(For some models)
Unit: mm (in.)
Adhesive tape: Thickness 0.8 mm (0.03 in.)
FRONT ’’A’’ EMBLEM
Edge of the trunk lidEdge of the inner taillight
104.5
(4.12)
21 (0.83)
17 (0.67)
22 (0.87)
CSX EMBLEM
TYPE-S EMBLEM
(For some models)
NOTE: When removing the emblems, take care not to scratch the body.1. To remove the front ‘‘A’’ emblem, remove the front grille (see page 20-160).
2. Clean the body surface with a shop towel dampened in isopropyl alcohol. After cleaning, keep oil, grease, and water from getting on the surface.
3. Apply the emblem where shown.
4. After installing the front ‘‘A’’ emblem, reinstall the front grille.
08/08/21 15:05:05 61SNR030_200_0172
ProCarManuals.com
DYNOMITE -2009-

ÃŽ
(#'

)
20-177
Openers
Component Location Index
TRUNK LID LOCK CYLINDER
TRUNK LID LATCH
FUEL FILL
DOOR LATCH
TRUNK LID OPENER CABLE/
FUEL FILL DOOR OPENER CABLE
HOOD OPENER CABLE HOOD LATCH
TRUNK LID OPENER/
FUEL FILL DOOR OPENER
HOOD RELEASE HANDLE Replacement, page 20-184
Replacement,page 20-185
Replacement, page 20-179
Replacement, page 20-178 Replacement, page 20-181
Replacement, page 20-182
08/08/21 15:05:10 61SNR030_200_0179
ProCarManuals.com
DYNOMITE -2009-




(#'
 )
20-179
Trunk Lid Opener Cable/Fuel Fill Door Opener Cable Replacement
A
B
C
Fastener Locations
:Clip,2
B : Cushion tape, 2
C
CB A
B A
A B C
SRS components are located in this area. Review the
SRS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the body and related parts.
1. Remove these items:
 Rear seat cushion (see page 20-133)
 Rear seat side bolster (see page 20-134)
 Front door sill trim, driver’s side (see step 3 onpage 20-66)
 Kick panel, driver’s side (see page 20-66)
 Rear door sill trim, both sides (see page 20-67)
 B-pillar lower trim, driver’s side (see page 20-72)
 Trunk side trim panel, left side (see step 6 on page 20-81)
 Trunk lid trim (see page 20-82)
 Trunk lid opener/fuel fill door opener (see page 20-182)
 Fuel cap adapter (see page 20-159)
2. Pull the carpet back as needed.
3. Release the opener cable (A) from the clips (B). Remove the cushion tape (C). 4. While pinching the hooks (A) from inside the
vehicle, remove the grommet (B) from the body.
5. Release the hook (A), then remove the grommet (B) from the fuel fill door latch (C).
(cont’d)
08/08/21 15:05:32 61SNR030_200_0181
ProCarManuals.com
DYNOMITE -2009-



20-180Openers
Trunk Lid Opener Cable/Fuel Fill Door Opener Cable Replacement (cont’d)
A
B
C
Fastener Locations
:Clip,4
A
B C
Front
B
A C
B
B
Front
6. Remove the fuel fill door opener cable from inside the body.
7. Detach the opener cable junction box (A) from the body.
8. Disconnect the trunk lid opener cable (B) from the trunk lid latch (C) (see page 20-185).
9. Release the trunk lid opener/fuel fill door opener cable from the clips.
10. Remove the trunk lid opener/fuel fill door opener cable from the vehicle. Take care not to kink the
cable. 11. Install the opener cable in the reverse order of
removal, and note these items:
 Align the marks (A) on the opener cable (B) with the cable clips (C) as shown.
 Replace any damaged clips and the cushion tape.
08/08/21 15:05:32 61SNR030_200_0182
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
S

pecial Tools Required
20-182 Openers
Trunk Lid Opener/Fuel Fill Door Opener Replacement
Fastener Location
:Bolt,1
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft) A
D E
B
B
C F

astener Location
:Screw,1
A
KTC trim tool set SOJATP2014
NOTE: Use the appropriate tool from the KTC trim tool
s
et to avoid damage when removing components.
1. Pry out the bottom edge of the front side cap (A) at the notch with the appropriate trim tool to detach
the hooks (B), and release the hooks (C), then
remove the cap from the front door sill trim (D).
2. Remove the opener lock cylinder (E), and loosen the bolt. 3

. Remove the screw securing the front door sill trim
(A) and trunk lid opener/fuel full door opener.
4. Remove the front door sill trim (see step 3 on page 20-66).
08/08/21 15:05:33 61SNR030_200_0184
ProCarManuals.com
DYNOMITE -2009-


20-183
Fastener Location
:Bolt,1
A
B
6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft) A
B
5. Remove the bolt, then remove the trunk lid opener/
fuel fill door opener (A) from the bolt (B). 6. Disconnect the trunk lid opener/fuel fill door opener
cable (A), then remove the opener (B). Take care
not to kink the cable.
7. Install the opener in the reverse order of removal, and note these items:
 Make sure the opener cable is connected properly.
 Make sure the trunk lid and fuel fill door open properly and lock securely.
 If the trunk lid or the fuel fill door does not open properly, adjust the position of the cable end on
the opener.
08/08/21 15:05:34 61SNR030_200_0185
ProCarManuals.com
DYNOMITE -2009-