trunk ACURA CSX 2006 Service Service Manual

System MenuData List Data List Indication
22-91
SecurityIgnition Key Cylinder Switch OFF/ON
Driver’s Door Switch OFF/ON
Front Passenger’s Door Switch OFF/ON
Driver’s Rear Door Switch OFF/ON
Passenger’s Rear Door Switch OFF/ON
Trunk Lid/Tailgate Switch OFF/ON
Front Passenger’s Door Lock Sw. (LOCK) OFF/ON
Front Passenger’s Door Lock Sw. (UNLOCK) OFF/ON
Front Passenger’s Door Lock Knob Sw. (UNLOCK) OFF/ON
Driver’s Rear Door Lock Knob Switch (UNLOCK) OFF/ON
Passenger’s Rear Door Lock Knob Sw. (UNLOCK) OFF/ON
Trunk Key Cylinder (UNLOCK) OFF/ON
Radio Switch OFF/ON
Hazard Switch OFF/ON
Hood Switch OFF/ON
Driver’s Door Key Cylinder Switch (LOCK) OFF/ON
Driver’s Door Key Cylinder Switch (UNLOCK) OFF/ON
Driver’s Door Look Switch (LOCK) OFF/ON
Driver’s Door Look Switch (UNLOCK) OFF/ON
Driver’s Door Look Knob Switch (LOCK) OFF/ON
Driver’s Door Look Knob Switch (UNLOCK) OFF/ON
Door LOCK Command OFF/ON
Door UNLOCK Command OFF/ON
Driver’s Door UNLOCK Command OFF/ON
Security Hazard Signal Command OFF/ON
Headlight Command OFF/ON
Headlight High Beam Command OFF/ON
Parking Light Command OFF/ON
(cont’d)
08/08/21 14:24:58 61SNR030_220_0093
ProCarManuals.com
DYNOMITE -2009-

•••
Function Test:
System Menu Data List Indication Data List and Operation Time
22-92Multiplex Integrated Control System
System Description (cont’d)
Door Locks
LOCK all doors Outputs LOCK signal 1 time (0.6 sec) to all doors
UNLOCK driver’s side door Outputs UNLOCK signal 1 time (0.6 sec) to driver’s
door
UNLOCK all doors Outputs UNLOCK signal 1 time (0.6 sec) to all doors
Lighting Interior Light Command Illuminates for 30 seconds.
LEFT Turn Signal Command Blinks for 5 seconds.
RIGHT Turn Signal Command Blinks for 5 seconds.
Hazard flasher Blinks turn signal (left and right) for 15 seconds.
Headlight Command Operates headlight (low) for 15 seconds.
Headlight HIGH Beam Command Operates headlight (high) for 15 seconds.
Fog Light Operates fog light relay for 15 seconds.
Parking Light Command Operates small lights for 15 seconds.
Keyless Trunk Lid/Tailgate Release Command Unlock trunk
Security Horn Command Operates horn for 1 second.
Wipers Windshield Wiper Motor LOW Command Operates windshield wiper motor for 5 seconds (low
speed).
Windshield Wiper Motor HIGH Command Operates windshield wiper motor for 5 seconds (high
speed).
Windshield Washer Command Operates windshield washer motor for 5 seconds.
Gauges Self Diagnostic Test
08/08/21 14:24:58 61SNR030_220_0094
ProCarManuals.com
DYNOMITE -2009-


(#')
µ
µ
µ
µ
YES
NO
YES
NO
22-93
Troubleshooting - B-CAN System Diagnosis Test Mode A
A
Check the ECM/PCM for DTCs and troubleshoot ECM/
PCM (see page 11-3) or F-CAN loss of communication
errors first, then do this diagnosis if the symptom is
relatedtotheB-CANsystem.
NOTE: If the HDS is not available, do the Test Mode 1 and Test Mode 2 (see page 22-97).
 Always cycle the ignition switch within 3 seconds when prompted in the DTC troubleshooting
procedures.
1. Compare the symptom with this list of B-CAN related systems:
 Gauge control module
 Exterior lights
 Turn signals
 Entry light control
 Interior lights
 Door-open and trunk-open indicators
 Horns (security and panic)
 Chimes (key-in, seat belt, lights-on, and parking brake)
 Power window/moonroof timer
 Wiper/washer
Security
 Keyless entry
 Power door locks
Keyinterlock
 Dash light brightness control
Go to step 2.
Go to the system troubleshooting for the
system with the symptom. 2. Connect the HDS to the data link connector (A),
then turn the ignition switch to ON (II).
3. From the BODY ELECTRICAL menu, select UNIT INFORMATION, and then select CONNECTED UNIT
listed to see if the following control units are
communicating with the HDS.
MICU
 Gauge control module
 Immobilizer-keyless control unit
 Climate control unit
 HandsFreeLink control unit
NOTE:  If one or more of the units are not communicating with the HDS, DETECT will be
displayed.
 If the unit is not communicating or the vehicle is not equipped, ‘‘Not Available’’ will be displayed.
Go to step 4.
If any of the control units are not
communicating, go to B-CAN System Diagnosis
Test Mode B (see page 22-94). If all units are not
communicating or only the MICU is communicating,
go to DTC B1000 troubleshooting (see page 22-102).
(cont’d)
Is the symptom related to the B-CAN system? Ar e al l cont r ol uni t s communi cat i ng w i t h t he H DS?
08/08/21 14:24:59 61SNR030_220_0095
ProCarManuals.com
DYNOMITE -2009-

(#')
µ
µ
µ
µ
YES
NO
YES
NOUnit not communicating
22-9422-94Multiplex Integrated Control System
Troubleshooting - B-CAN System
Diagnosis Test Mode A (cont’d)
Troubleshooting - B-CAN System
Diagnosis Test Mode B
4. Select the system that has the problem from the
BODY ELECTRICAL menu, then select DTCs.
Go to step 5.
If the problem is related to one of the
following items, go to B-CAN System Diagnosis
Test Mode C (see page 22-95) if the system does
not stop or turn off. Go to Test Mode D (see page
22-96) if the system does not run or turn on.
 Exterior lights
 Turn signals
 Entry light control
 Interior lights
 Horn (security and panic)
 Wiper/washer
If the problem is related to one of the following
items, go to the troubleshooting for that individual
system.  Gauge control module
 Door-open and trunk-open indicators
 Chimes (key-in, seat belt, lights-on, and parking brake)
Security
 Keyless entry
Keyinterlock
 Dash light brightness control
 Audio system
 Navigation (if equipped)
 HandsFreeLink (if equipped)
5. Record all DTCs, and sort them by DTC type.
6. Troubleshoot the DTC(s) in this order:  Battery voltage DTCs.
 Internal error DTCs.
 Loss of communication DTCs. Begintroubleshooting with the lowest number first
(Example: if DTC B1008 and B1011 are retrieved,
begin by troubleshooting B 1008).
 Signal error DTCs. Do this diagnosis if any of the control units are not
communicating (Not Available is displayed in the HDS)
as found by the B-CAN System Diagnosis Test Mode A
(see page 22-93).
1. Using the HDS, select the system that has the symptom from the BODY ELECTRICAL menu.
2. Select DTCs, and then check for loss of communication DTCs.
Go to step 3.
Replace the MICU.
3. Do the input test for the unit not communicating with the HDS.
MICU (see page 22-109)
Gauge control module (see page 22- 271)
Immobilizer-keyless control unit (see page
22-330)
Climate control unit (see page 21-24)
HandsFreeLink control unit (see page 23-388)
Are any DTCs indicated?
Ar e any l oss of communi cat i on DT Cs i nd i cat ed ?
08/08/21 14:24:59 61SNR030_220_0096
ProCarManuals.com
DYNOMITE -2009-

(#')
µ
µ
µ
µ
YES
NO
YES
NOUnit not communicating
22-9422-94Multiplex Integrated Control System
Troubleshooting - B-CAN System
Diagnosis Test Mode A (cont’d)
Troubleshooting - B-CAN System
Diagnosis Test Mode B
4. Select the system that has the problem from the
BODY ELECTRICAL menu, then select DTCs.
Go to step 5.
If the problem is related to one of the
following items, go to B-CAN System Diagnosis
Test Mode C (see page 22-95) if the system does
not stop or turn off. Go to Test Mode D (see page
22-96) if the system does not run or turn on.
 Exterior lights
 Turn signals
 Entry light control
 Interior lights
 Horn (security and panic)
 Wiper/washer
If the problem is related to one of the following
items, go to the troubleshooting for that individual
system.  Gauge control module
 Door-open and trunk-open indicators
 Chimes (key-in, seat belt, lights-on, and parking brake)
Security
 Keyless entry
Keyinterlock
 Dash light brightness control
 Audio system
 Navigation (if equipped)
 HandsFreeLink (if equipped)
5. Record all DTCs, and sort them by DTC type.
6. Troubleshoot the DTC(s) in this order:  Battery voltage DTCs.
 Internal error DTCs.
 Loss of communication DTCs. Begintroubleshooting with the lowest number first
(Example: if DTC B1008 and B1011 are retrieved,
begin by troubleshooting B 1008).
 Signal error DTCs. Do this diagnosis if any of the control units are not
communicating (Not Available is displayed in the HDS)
as found by the B-CAN System Diagnosis Test Mode A
(see page 22-93).
1. Using the HDS, select the system that has the symptom from the BODY ELECTRICAL menu.
2. Select DTCs, and then check for loss of communication DTCs.
Go to step 3.
Replace the MICU.
3. Do the input test for the unit not communicating with the HDS.
MICU (see page 22-109)
Gauge control module (see page 22- 271)
Immobilizer-keyless control unit (see page
22-330)
Climate control unit (see page 21-24)
HandsFreeLink control unit (see page 23-388)
Are any DTCs indicated?
Ar e any l oss of communi cat i on DT Cs i nd i cat ed ?
08/08/21 14:24:59 61SNR030_220_0096
ProCarManuals.com
DYNOMITE -2009-

µ
µ
MICU
Item
YES
NO
22-98Multiplex Integrated Control System
Troubleshooting - B-CAN System Diagnosis Test Mode 1 and Test Mode 2
(without the HDS) (cont’d)
Driver’s door lock switch (UNLOCK)
Driver’s door lock switch (LOCK)
Driver’s door lock knob switch (UNLOCK)
Driver’s door lock knob switch (LOCK)
Driver’s door key cylinder switch (UNLOCK)
Driver’s door key cylinder switch (LOCK)
Front passenger’s door lock switch (UNLOCK)
Front passenger’s door lock switch (LOCK)
Front passenger’s door lock knob switch
(UNLOCK)
Left rear door lock knob switch (UNLOCK)
Right rear door lock knob switch (UNLOCK)
Driver’s door switch (OPEN)
Front passenger’s door switch (OPEN)
Left rear door switch (OPEN)
Right rear door switch (OPEN)
Trunk lid latch switch (OPEN)
Audio switch
Windshield wiper HI/LO switch
Windshield wiper INT/LO switch
Windshield wiper MIST switch
Windshield washer switch (ON)
Windshield wiper intermittent dwell time
controller
Windshield wiper motor park switch
Turn signal switch (LEFT)
Turn signal switch (RIGHT)
Hazard warning switch (ON)
Headlight switch (ON)
Headlight switch (OFF)
Lighting switch (ON)
Dimmer switch (ON)
Passing switch (ON)
Fog light switch (ON)
Hood switch (OPEN)
A/C pressure switch/thermal protector
Transmission range switch (P)
Ignition key cylinder switch
Brake switch (ON)
: A second key is necessary to check the key cylinder inputs.
Be sure to rotate the key cylinder switch two
times to each position (lock and lock, unlock
and unlock) to ensure the door lock knob
switch is in the appropriate position. Go to function and input test for the system
related to the failure.
Repair the open, short, or replace the faulty
switch.
Does the ceiling light work properly in all switch posi t i ons?
08/08/21 14:24:59 61SNR030_220_0100
ProCarManuals.com
DYNOMITE -2009-

(#')
22-99
Sleep and Wake-up Mode Test
1. Shift to the sleep mode:Turn the ignition switch to LOCK (0), and remove the key. If the MICU receives no signals from the inputs listed
below, it will go into sleep mode in less than 40 seconds.
Driver’s door lock switch (LOCK or UNLOCK)
Driver’s door key cylinder switch (LOCK or UNLOCK)
Front passenger’s door lock switch (LOCK or UNLOCK)
Trunk lid latch switch (Trunk lid closed)
Hazard warning switch (OFF)
2. Confirm the sleep mode: Measure the frequency on the B-CAN communication line (PNK wire); there should be 0 Hz when the system is in
the sleep mode. Check the parasitic draw at the battery while shifting into the sleep mode; the amperage should
change from about 200 mA to less than 35 mA.
3. Shift to the wake up mode: When the ignition switch is turned to ON (II), the MICU, gauge control module, immob ilizer-keyless control unit,
and ECM/PCM wake up at the same time without ‘‘talking’’ to each other through the communication lines. When
any switch in the multiplex integrated control system is turned on, it wakes up its related control unit which, in
turn, wakes up the other units. After confirming the sleep mode, look in the following table for the switch most
related to the problem. Operate that switch and see if its control unit wakes up.
NOTE: If any control unit is faulty and will not wake up, several circuits in the system will malfunction at the same
time. In the table below, the control unit is followed by a list of the switches and input signals that can wake it up.
Door switches (door open)
Driver’s door lock switch (LOCK or UNLOCK)
Driver’s door lock knob switch (LOCK or UNLOCK)
Driver’s door key cylinder switch (LOCK or UNLOCK)
Front passenger’s door lock switch (LOCK or UNLOCK)
Front passenger’s door lock knob switch (LOCK or UNLOCK)
Left rear door lock knob switch
Right rear door lock knob switch
Trunk lid latch switch (Trunk lid open)
Hood switch (with security) (hood open)
Hazard warning switch (ON)
Combination light switch (Parking, Headlight, Dimmer, Passing ON)
Ignition key switch (key inserted)
08/08/21 14:25:00 61SNR030_220_0101
ProCarManuals.com
DYNOMITE -2009-

Î
(#')
22-112Keyless/Power Door Locks/Security System
Component Location Index
NAVIGATION UNIT or
AUDIO UNIT
IMMOBILIZER-KEYLESS
CONTORL UNIT
(With built-in receiver)
SECURITY INDICATOR GAUGE CONTORL MODULE
(SPEEDO)
HEADLIGHT
HOOD SWITCH
MICU
(Built into the under-
dash fuse/relay box)
HORN
TRANSMITTER
LOCK BUTTON TRUNK BUTTON
UNLOCK BUTTON
IGNITION KEY PANIC BUTTONSymptom Troubleshooting,
page 22-126
Replacement, page 22-332
Replacement, page 22-174
Adjustment, page 22-173
Bulb Replacement, page 22-177
Test, page 22-141
Input Test, page 22-131
Test/Replacement, page 22-146
Test/Replacement, page 22-142
08/08/21 14:25:04 61SNR030_220_0114
ProCarManuals.com
DYNOMITE -2009-

Î
Î
22-113
LEFT REAR DOOR LOCK
ACTUATOR/
KNOB SWITCHDRIVER’S DOOR KEY CYLINDER SWITCH
DRIVER’S DOOR LOCK SWITCH
(Built into the power
window master switch) DRIVER’S DOOR LOCK
ACTUATOR/
KNOB SWITCH TRUNK LID RELEASE ACTUATOR/
LATCH SWITCH
LEFT REAR DOOR SWITCH IGNITION KEY SWITCH
DRIVER’S DOOR
SWITCH
RIGHT REAR DOOR LOCK
ACTUATOR/KNOB SWITCHFRONT PASSENGER’S
DOOR SWITCHFRONT PASSENGER’S DOOR
LOCK ACTUATOR/KNOB SWITCH
FRONT PASSENGER’S
DOOR LOCK SWITCH
RIGHT REAR DOOR SWITCH
LICENSE PLATE LIGHTS
INNER TAILLIGHTTAILLIGHTActuator Test,
page 22-137
Knob Switch Test,
page 22-138 Test, page 22-140
Replacement, page 20-9
Test, page 22-139 Acutuator Test,page 22-137
Knob Switch Test, page 22-138 Actuator Test, page 22-141
Latch Switch Test, page 22-200
Test, page 22-207
Actuator Test, page 22-137
Knob Switch Test, page 22-138 Actuator Test, page 22-137
Knob Switch Test, page 22-138
Test, page 22-139
Replacement, page 22-139
Replacement, page 22-180
Replacement,page 22-179
Replacement, page 22-179
08/08/21 14:25:08 61SNR030_220_0115
ProCarManuals.com
DYNOMITE -2009-

(#')
Security Alarm System
22-114Keyless/Power Door Locks/Security System
System Description
The security alarm system is armed automatically after the doors, hood, and trunk are closed and locked. For the
system to arm, the ignition switch must be to LOCK (0), the key must be removed from the ignition switch, and the
MICU must receive signals that the doors, hood, and trunk are closed and locked. The alarm can be disarmed at any
time by unlocking the driver’s door with the key or pressing the UNLOCK button on the transmitter.
When everything is closed and locked, the only i
nputs that are grounded, and have 0 V, are the driver’s door lock knob
switch (LOCK position), and the audio unit or navigation unit (if equipped). In other words, all of the other switches are
open, and have about 10 to 12 V, including the key cylinder switches. The security indicator in the gauge control
module (speedo) begins to flash immediately after the vehicle is completely closed and locked, and 15 seconds later,
the security system arms. If the security indicator does not flash, the system is not arming. A beep sounds and parking
lights flash to confirm the security alarm system is armed if the LOCK button is pressed a second time within
5 seconds.
If one of the switches is misadjusted or shorted internally, or there is a short in the circuit, the security system will not
arm. As long as the control unit continues to receive a ground signal (0 V), it senses that the vehicle is not closed and
locked, and the system will not arm. A switch that is slightly misadjusted can cause the alarm to sound for no apparent
reason. In this case, a significant change in outside air temperature, the vibration of a passing truck, or someone
bumping into the vehicle could cause the alarm to sound. There is no glass breakage or motion detector feature.
If anything is opened or improperly unlocked after the system is armed, the control unit receives a ground signal from
that switch, and the 10 to 12 V reference drops to 0 V. If the audio unit or navigation unit (if equipped) is disconnected,
the input loses its ground, and the input voltage goes to 10 to 12 V. The system sounds the alarm when any of these
occur:
 A door or the trunk is forced open.
 A door is unlocked without using the key or the transmitter.
 The hood is opened.
 The audio unit or navigation unit (if equipped) is disconnected.
 The transmitter PANIC button is pressed.
When the system sounds the alarm, the horn sounds and the exterior lights flash for 2 minutes. The alarm can be
stopped at any time by unlocking the driver’s door with the key or by pressing any button on the transmitter.
08/08/21 14:25:08 61SNR030_220_0116
ProCarManuals.com
DYNOMITE -2009-