ignition ACURA CSX 2006 Service Repair Manual

µ
µ
µ
µ µ
µ µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
11-400EVAP System
DTC Troubleshooting (cont’d)
19. Turn the ignition switch to ON (II).
20. Reset the ECM/PCM with the HDS.
21. Do the ECM/PCM idle learn procedure (see page
11-310).
22. Select EVAP CVS ON in the INSPECTION MENU with the HDS.
23. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the EVAP canister vent shut valve and
theECM/PCM,thengotostep1.
Go to step 24.
24. Monitor the OBD STATUS for DTC P0498 in the DTCs MENU with the HDS.
Troubleshooting is complete. If any other
Temporary DTCs or DTCs were indicated in step 23,
go to the indicated DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the EVAP canister
vent shut valve and the ECM/PCM, then go to step
1. If the screen indicates NOT COMPLETED, go to
step 22. 25. Reconnect all connectors.
26. Update the ECM/PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
27. Select EVAP CVS ON in the INSPECTION MENU with the HDS.
28. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the EVAP canister vent shut valve and
the ECM/PCM. If the ECM/PCM was updated,
substitute a known-good ECM/PCM (see page 11-7),
then go to step 27. If the ECM/PCM was substituted,
go to step 1.
Go to step 29.
29. Monitor the OBD STATUS for DTC P0498 in the DTCs MENU with the HDS.
If the ECM/PCM was updated,
troubleshooting is complete. If the ECM/PCM was
substituted, replace the original ECM/PCM
(see page 11-228). If any other Temporary DTCs or
DTCs were indicated in step 28, go to the indicated
DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the EVAP canister
vent shut valve and the ECM/PCM. If the ECM/PCM
was updated, substitute a known-good ECM/PCM
(see page 11-7), then go to step 27. If the ECM/PCM
was substituted, go to step 1. If the screen indicates
NOT COMPLETED, go to step 27.
Is DT C P0498 ind icated ?
Does t he scr een i nd i cat e PASSE D? Is DT C P0498 ind icated ?
Does t he scr een i nd i cat e PASSE D?
08/08/21 14:33:24 61SNR030_110_0400
ProCarManuals.com
DYNOMITE -2009-

(#' 
)
µ
µ
µ
µ µ
µ
DTC P0499:
YES
NO
YES
NO YES
NO
11-401
EVAP Canister Vent Shut Valve
Circuit High Voltage
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Select EVAP CVS ON in the INSPECTION MENU with the HDS.
4. Check for Temporary DTCs or DTCs with the HDS.
Go to step 5.
Intermittent failure, the system is OK at this
time. Check for poor connections or loose terminals
at the EVAP canister vent shut valve and the ECM/
PCM.
5. Update the ECM/PCM if it does not have the latest software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
6. Select EVAP CVS ON in the INSPECTION MENU with the HDS.
7. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the EVAP canister vent shut valve and
the ECM/PCM. If the ECM/PCM was updated,
substitute a known-good ECM/PCM (see page 11-7),
then go to step 6. If the ECM/PCM was substituted,
go to step 1.
Go to step 8. 8. Monitor the OBD STATUS for DTC P0499 in the
DTCs MENU with the HDS.
If the ECM/PCM was updated,
troubleshooting is complete. If the ECM/PCM was
substituted, replace the original ECM/PCM
(see page 11-228). If any other Temporary DTCs or
DTCswereindicatedinstep7,gototheindicated
DTC’s troubleshooting.
If the screen indicates FAILED, check for poor
connections or loose terminals at the EVAP canister
vent shut valve and the ECM/PCM. If the ECM/PCM
was updated, substitute a known-good ECM/PCM
(see page 11-7), then go to step 6. If the ECM/PCM
was substituted, go to step 1. If the screen indicates
NOT COMPLETED, go to step 6.
Is DT C P0499 ind icated ?
Is DT C P0499 ind icated ? Does t he scr een i nd i cat e PASSE D?
08/08/21 14:33:24 61SNR030_110_0401
ProCarManuals.com
DYNOMITE -2009-

µµ
µ 
(#' 

)
µ
µ
µ
µ µ
µ
DTC P1454:
DTC P2422:
YES
NO
YES
NO YES
NO
11-402EVAP System
DTC Troubleshooting (cont’d)
A
FTP Sensor Range/Performance
Problem
EVAP Canister Vent Shut Valve
Stuck Closed Malfunction
NOTE: Before you troubleshoot, record all freeze data
and any on-board snapshot, and review the general
troubleshooting information (see page 11-3).
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0).
4. Remove the fuel fill cap, and wait 1 minute.
5. ChecktheFTPSENSORintheDATALISTwiththe HDS.
Go to step 6.
Go to step 17.
6. Install the fuel fill cap.
7. Clear the DTC with the HDS.
8. Start the engine, and let it idle without load (A/T in P or N, M/T in neutral) until the radiator fan comes
on.
9. Monitor the OBD STATUS for DTC P1454 in the DTCs MENU with the HDS.
Go to step 10.
If the screen indicates PASSED, intermittent
failure, the system is OK at this time. Check for
poor connections or loose terminals at the FTP
sensor, the EVAP canister vent shut valve, and the
ECM/PCM. Also check for a blockage in the vent
hoses and the drain joint. If the screen indicates
NOT COMPLETED, keep idling until a result comes
on. 10. Clear the DTC with the HDS.
11. Turn the ignition switch to LOCK (0).
12. Remove the EVAP canister vent shut valve from the
EVAP canister (see page 11-409).
13. Connect the 2P connector to the EVAP canister vent shut valve.
14. Turn the ignition switch to ON (II).
15. Select EVAP CVS ON in the INSPECTION MENU with the HDS.
16. Check the EVAP canister vent shut valve (A) operation.
Check for a blockage in the EVAP canister,
the vent hoses, and the drain joint, then install the
EVAP canister vent shut valve, and go to step 23.
Replace the EVAP canister vent shut valve
(see page 11-409), then go to step 23.
Is i t bet w een 0.67 and 0.67 k Pa ( 5 and 5 mmH g, 0.2 and 0.2 i n.H g), or 2.4 and 2.6 V ?
Does t he scr een i nd i cat e F AILE D? Does t he v al v e oper at e?
08/08/21 14:33:24 61SNR030_110_0402
ProCarManuals.com
DYNOMITE -2009-

µµ
µ µµ
µ

 µ
µ µ
µ
µ
µ
YES
NO YES
NO
YES
NO
11-403
A
B
A
17. Disconnect the air tube (A) from the FTP sensor (B).
18. ChecktheFTPSENSORintheDATALISTwiththeHDS.
Check for a blockage in the FTP sensor air
tube or the vent, then go to step 23.
Go to step 19.
19. Turn the ignition switch to LOCK (0).
20. Remove the FTP sensor (A) from the EVAP canister with its connector connected (see page 11-408). 21. Turn the ignition switch to ON (II).
22. ChecktheFTPSENSORintheDATALISTwiththe
HDS.
Check for debris or clogging at the EVAP
canister and the FTP sensor port, then go to
step 23.
Replace the FTP sensor (see page 11-408),
then go to step 23.
23. Turn the ignition switch to ON (II).
24. Reset the ECM/PCM with the HDS.
25. Do the ECM/PCM idle learn procedure (see page 11-310).
26. Start the engine, and let it idle without load (A/T in P or N, M/T in neutral) until the radiator fan comes
on.
27. Check for Temporary DTCs or DTCs with the HDS.
Check for poor connections or loose
terminals at the FTP sensor, the EVAP canister vent
shut valve, and the ECM/PCM, then go to step 1.
Go to step 28.
(cont’d)
Is i t bet w een 0.67 and 0.67 k Pa ( 5 and5 mmH g, 0.2 and 0.2 i n.H g), or 2.4 and 2.6 V ? Is i t bet w een 0.67 k Pa and 0.67 k Pa ( 5 and
5 mmH g, 0.2 and 0.2 i n.H g), or 2.4 and 2.6 V ?
Is DT C P1454 and/ or P2422 indicated?
08/08/21 14:33:25 61SNR030_110_0403
ProCarManuals.com
DYNOMITE -2009-

µ
µ
µ

Î
(#')
µ
µ
µ
µ µ
µ
Special Tools Required
YES
NO
YES
NO YES
NO
K20Z3 engine
11-405
Fuel Cap Warning Message System Troubleshooting
AB
C A
B
C 07JAZ-001000B
 Vacuum/pressure gauge, 0 4 in.Hg 07JAZ-001000B
 Vacuum pump/gauge, 0 30 in.Hg, Snap-on YA4000A
or equivalent, commercially available
Do this procedure if the fuel cap warning message
comes on frequently, or if the message does not go off
after the fuel fill cap is tightened and the vehicle is
driven several days.
1. Check the fuel fill cap (the cap must say TIGHTEN TO CLICK). It should turn 1/4 after it’s tight, then it
clicks.
Go to step 2.
Replace or tighten the cap, then go to step 13.
2. Check the fuel fill cap seal (A) and the fuel fill pipe mating surface (B). Verify that the fuel fill cap tether
cord (C) is not caught under the cap.
Replace the fuel fill cap or the fuel fill pipe,
then go to step 13.
Go to step 3. 3. Reinstall and tighten the fuel fill cap.
4. Clear the DTC with the HDS.
5. Start the engine. Hold the engine speed at
3,000 rpm without load (in neutral) until the
radiator fan comes on, then let it idle for 1 minute.
6. Test drive at 72 km/h (45 mph) for 1 minute or more.
Go to step 7.
Intermittent failure, the system is OK at this
time.
7. Turn the ignition switch to LOCK (0).
8. Disconnect the vacuum hose (A) from the EVAP canister purge valve (B) in the engine compartment,
and connect a T-fitting (C) between the vacuum
gauge and the vacuum pump/gauge 0 30 in.Hg,
and the EVAP canister purge valve as shown.
(cont’d)
Is the correct f uel f ill cap installed and properlytightened?
Is the f uel f ill cap seal missing or damaged, is thef uel f i l l pi pe d amaged , or i s t he t et her cor d caughtund er the cap? Does f uel cap w ar ni ng message come on?
08/08/21 14:33:26 61SNR030_110_0405
ProCarManuals.com
DYNOMITE -2009-

µ
µ
µ
µ
YES
NO
YES
NO
11-406 EVAP System
Fuel Cap Warning Message System Troubleshooting (cont’d)
9. Turn the ignition switch to ON (II).
10. Apply about 2 kPa (15 mmHg, 0.6 in.Hg) of vacuum to the hose.
11. Select the EVAP PCS ON in the INSPECTION MENU with the HDS.
Check for a blockage at the EVAP canister
purge line between EVAP canister purge valve and
the EVAP canister, then go to step 12.
Replace the EVAP canister purge valve
(see page 11-409), then go to step 12.
12. Reconnect all hoses.
13. Turn the ignition switch to ON (II).
14. Reset the ECM with the HDS.
15. Do the ECM idle learn procedure (see page 11-310).
16. Start the engine. Hold the engine speed at 3,000 rpm without load (in neutral) until the
radiator fan comes on, then let it idle for 1 minute.
17. Test drive at 72 km/h (45 mph) for 1 minute or more.
Go to step 1 and recheck.
Troubleshooting is complete.
Does t he v acuum r el ease i mmed i at el y ?
Does t he f uel cap message come on?
08/08/21 14:33:26 61SNR030_110_0406
ProCarManuals.com
DYNOMITE -2009-

Î
Î(#'


")
Fluid Capacity
1.5 L (1.6 US qt) at fluid change
1.7 L (1.8 US qt) at overhaul
13-5
Transmission Fluid Inspection and Replacement
A B
C
C
44 N·m
(4.5 kgf·m,
33 lbf·ft)
A
39 N·m
(4.0 kgf·m,
29 lbf·ft)
B D
1. Raise the vehicle on a lift.
2. Remove the filler plug (A) and the sealing washer
(B). Check the condition of the MTF, and make sure
it is at the proper level (C).
3. If the MTF is dirty, remove the drain plug (A) and the sealing washer (B), and drain it.
4. Install the drain plug with a new sealing washer, and refill the transmission with MTF to the proper
level. Always use Acura Manual Transmission Fluid
(MTF).
5. Install the filler plug (C) with a new sealing washer (D). 6. If the maintenance minder required to replace the
MTF, reset the maintenance minder (see page 3-4).
If it did not reset, go to step 7.
7. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC) (see step 2 on page 11-3).
8. Turn the ignition switch to ON (II).
9. Make sure the HDS communicates with the vehicle and the engine control module (ECM). If it does not
communicate, go to the DLC circuit troubleshooting
(see page 11-204).
10. Select BODY ELECTRICAL with the HDS.
11. Select ADJUSTMENT in the GAUGES MENU with the HDS.
12. Select RESET in the MAINTENANCE MINDER with the HDS.
13. Select MAINTENANCE SUB ITEM 3, and reset the MTF life with the HDS.
Replace. Replace.
08/08/21 14:44:17 61SNR030_130_0007
ProCarManuals.com
DYNOMITE -2009-

ØÚÓ



Î
(#' 
)
How to Troubleshoot Circuits at the ECM
Connectors
13-71
Reverse Lockout System
General Troubleshooting Information
A
E
A
D
B
C A
D
B
CA
NOTE: The ECM overwrites data and monitors the EVAP
system for up to 30 minutes after the ignition switch is
turned to LOCK (0). Jumping the SCS line after turning
the ignition switch to LOCK (0) cancels this function.
Disconnecting the ECM during this function, without
jumping the SCS line first, can damage the ECM.
1. Jump the SCS line with the HDS.
2. Remove the cover (A).
3. Lift up the under-hood fuse/relay box (D).
4. Remove the coolant reservoir (E). Disconnect ECM connectors A, B, and C.
NOTE: ECM connectors A, B, and C have symbols
(A= , B= , C= ) embossed on them for
identification. 5. When troubleshooting is done at the ECM
connector, use the terminal test port (A) above the
terminal you need to check.
6. Connect one side of the patch cord’s terminals (A) to a commercially available digital multimeter (B),
and connect the other side cord’s terminals (C) to a
commercially available banana jack (Pomona
Electronics Tool No. 3563 or equivalent) (D).
7. Gently contact the pin probe (male) at the terminal test port from the terminal side. Do not force the
tips into the terminals.
 For accurate results, always use the pin probe (male).
 To prevent damage to the c onnector
terminals, do not insert test equipment
probes, paper clips, or other substitutes as
they can damage the terminals. Damaged
terminals cause a poor connection and an
incorrect measurement.
 Do not puncture the insulation on a wire. Punctures can cause poor or intermittent
electrical connections.
08/08/21 14:46:38 61SNR030_130_0073
ProCarManuals.com
DYNOMITE -2009-

Î
(#'


)Vehicle speed Inhibitor Reverse selection
13-73
System Description
With 5th/6th selected
With reverse selected
Select lever
Change lever Select lock
cam A
Select lock cam B Select lock return spring
Direction of reverse selection Locked position
Inhibitor OFF
At vehicle speeds of 20 km/h (12 mph) or more, the ECM, which monitors the signals from the output shaft
(countershaft) speed sensor, activates the r everse lockout solenoid, which pushes select lock cam B into the locked
position. As a result, the select lever ca nnot rotate to the reverse select position, making it impossible to engage
reverse gear. As the vehicle speed drops to 15 km/h (9 mph) or less, the ECM turns off the reverse lockout solenoid.
The select lock return spring pulls back select lock cam B, enabling the select lever to move freely so reverse gear can
be selected.
Above 20 km/h (12 mph) ON Not allowedBelow 15 km/h (9 mph) OFF Allowed
Ignition switch LOCK (0) OFF Allowed
08/08/21 14:46:39 61SNR030_130_0075
ProCarManuals.com
DYNOMITE -2009-

Î
(#'


)
(#'


)µ
µ
µ
µ
Driver can select reverse gear when vehicle
speed is 20 km/h (12 mph) or more
YES
NO
YES
NO
13-7413-74 Reverse Lockout System
Circuit Diagram
Symptom Troubleshooting
GRN/BLKYEL
1 2
BLK/YEL BLU
IG1
BAT WHT
BATTERY
UNDER-HOOD
FUSE/RELAY
BOX
IGNITION
SWITCH
IG1HOTinON(II)
and START (III)
UNDER-DASH
FUSE/RELAY
BOX
REVERSE
LOCKOUT
SOLENOID
No. 1
(100 A)
No. 3
(10 A) No. 2
(50 A)
GRN
ECM A27 RVS
NOTE:
 When checking if the transmission will shift to reverse while the wheels are being driven forward,
raise the vehicle on a lift, make sure it is securely
supported, and allow the front wheels to rotate freely.
 Do not release the clutch pedal if you can select reverse gear while the wheels are driven forward.
 When the vehicle is on a lift, and you make the wheels rotate, turn off the VSA system by the VSA
OFF switch.
1. Turn the ignition switch to LOCK (0).
2. Check the No. 3 (10 A) fuse in the under-dash fuse/ relay box.
Reinstallthefuse,thengotostep3.
Install a new No. 3 (10 A) fuse, and recheck. If
the fuse continues to blow, check for short to body
ground in the wire between the No. 3 (10 A) fuse in
the under-dash fuse/relay box and the r everse
lockout solenoid.
3. Test-drive the vehicle.
4. Check for fuel and emissions system’s DTC with the HDS.
Go to the indicated DTC’s troubleshooting.
Go to step 5.
IsthefuseOK?
Ar e t her e any DT Cs st or ed i n t he f uel andemi ssi ons?
08/08/21 14:46:39 61SNR030_130_0076
ProCarManuals.com
DYNOMITE -2009-