Battery ACURA CSX 2006 Service Repair Manual

Î

Service Precautions
System InitializationEntering the Security Code
GPS Initialization
23-268Navigation System
General Troubleshooting Information (cont’d)
The navigation system lost power and is acquiring its
location from the GPS satellites. This usually takes
less than 10 minutes.
* Start the engine.
*Parkthevehicleinanopenareaawayfromtrees,
* Remove loose articles, cell phones, or electrical
* If this screen is displayed repeatedly when starting power lines, and tall buildings.
accessories located near the GPS antenna.
the vehicle, see your dealer.
 If you need to replace the navigation unit, you can
back-up the navigation data and transfer it to a new
navigation unit. See Save users memory (see page
23-310).
 When the battery is disconnected, the internal GPS clock resets to 0:00. The clock resets to the correct
time after the system finishes GPS initialization.
 Before disconnecting the battery, make sure you have the anti-theft codes for the audio system and the
navigation system, and write down the audio presets.
Also obtain any PGM-FI or transmission DTCs and
freeze frame date (which are lost when the ECM/PCM
loses power).
 After reconnecting the battery, you have to wait to get the initial signal from the satellite. It will take from 10
to 45 minutes.
 Adjust the setup clock settings (time zone and daylight savings) in the navigation system.
 Before returning the vehicle to the client, enter the anti-theft codes for the audio system and the
navigation system.
If the navigation system loses power (like the battery
was disconnected), the navigation system requires
initialization. Once completed, your system is ready to
use.
This initialization requires the following:  Entering the 4-digit anti-theft security code to unlock the system
 GPS initialization (may not be needed depending of the length of time the system was without power)
 Map matching to align the GPS to a location on the map Any time the navigation system loses power, you need
to enter the 4-digit anti-theft code on the navigation
system display. This 4-digit code is located on a small
code card that was given to the customer. Enter the 4-
digit code, then select Done.
If the navigation system anti-theft code is missing, use
the interactive Network (iN) to look it up. You need the
serial number for the navigation unit to do this.
You can view the serial number by entering the
diagnostic mode. Select Unit Check from the main
menu, then the ECU info diagnostic screen. This allows
you to get the serial number without removing the
navigation unit.
The iN may display more than one code for a given
serial number. This is because serial numbers are not
unique. You may have to try more than one 4-digit code.
If no code is shown, or if the code(s) given do not work
in the navigation unit, contact the Automobile Warranty
department. If the code 0000 works, replace the
navigation unit.
When replacing the navigation unit or audio unit, make
sure you give the client the new anti-theft security code.
NOTE: You must park the vehicle outside with a clear
view of the southern sky.
Depending on the length of time the battery was
disconnected, your system may require GPS
initialization. If it does, the following screen appears:
08/08/21 14:15:38 61SNR030_230_0271
ProCarManuals.com
DYNOMITE -2009-

(#'#
)
DTC Description CircuitFailure DetectionPageAlso Check for
23-275
DTC Troubleshooting Index




1001 FROM system Info
Error Navigation unit internal data error. (see page 23-320) Low or weak battery
voltage
1101 Media Bus Send Error Media
condition
monitoringNavigation unit internal media error. (see page 23-320) Low or weak battery
voltage
1201 DVD High Temp DVD drive Navigation unit temperature above the upper limit. Failure in navigation unit fan circuit. (see page 23-321) Low or weak
battery voltage
High temperature
around the
navigation unit
1202 DVD Low Temp DVD drive Navigation unit temperature below the lower limit. (see page 23-321) Low or weak
battery voltage
High temperature
around the
navigation unit
1301 GPS Antenna Error GPS AntennaGPS antenna circuit malfunction. (see page 23-322) Low or weak battery
voltage
1302 GPS Receiver Error 1 GPS
ReceiverGPS antenna circuit malfunction.
Navigation unit internal GPS receiver
malfunction. (see page 23-323) Low or weak battery
voltage
1303 GPS Receiver Error 2 GPS
ReceiverNavigation unit internal GPS receiver
malfunction. (see page 23-324) Low or weak battery
voltage
1305 Gyro Error 2: ECU Temp XX °C Gyro Navigation unit internal gyro malfunction. (see page 23-324) Low or weak battery
voltage
1306 Vehicle Speed Pulse Vehicle
Speed PulseVSP circuit malfunction. (see page 23-325) Check for F-CAN
DTCs
1307 DVD Read Error DVD Scratched/Dirty DVD or navigation unit internal DVD ROM drive. (see page 23-325) Low or weak battery
voltage
1402 Audio Error 2 CD Mechanical malfunction in the CD changer. (see page 23-326) Low or weak battery voltage
1409 Audio Error 9 XM XM Antenna/circuit malfunction. (see page 23-326) Low or weak battery voltage
2607 XM Diag XM GA-NET Bus circuit malfunction Open/Short. XM Antenna circuit malfunction. (see page 23-327)
2609 VRAM Diag ECU VRAM Navigation unit internal VRAM malfunction. (see page 23-329)
2610 DRAM Diag ECU DRAM Navigation unit internal DRAM malfunction. (see page 23-330)
2701 GPS Diag: Antenna GPS GPS antenna malfunction. (see page 23-330)
2702 GPS Diag: Receiver in Navi GPS GPS antenna malfunction. (see page 23-331)
2703 Aircon Diag Aircon Communication error between climate control unit and navigation unit (open/short). (see page 23-331) Check for F-CAN
DTCs
2705 HFL Diag HFL HandsFreeLink control unit internal malfunction. (see page 23-334) Check for F-CAN DTCs
2706 Gyro Diag: ECU Temp XX °C Gyro Navigation unit internal malfunction. (see page 23-336)
2707 Mic Diag Mic Mic circuit malfunction Open/Short. (see page 23-337)
Flash ROM
management
08/08/21 14:15:41 61SNR030_230_0278
ProCarManuals.com
DYNOMITE -2009-

(#'#
)
Symptom Diagnostic procedure Also check for
23-276
Navigation System
Symptom Troubleshooting Index
































 








Navigation system stays on the GPS
initialization screen
System Initialization (see page
23-268) Navigation unit
GPS antenna/cable is
disconnected or damaged
The wrong color DVD is installed
The DVD is damaged or dirty
Harness/fuses/switches
Vehicle position icon constantly
leaves road, moves erratically, or is
displayed very far from actual
vehicle position Symptom Troubleshooting
(see page 23-344)
Navigation unit
GPS antenna/cable
ECM/PCM (speed and fuel pulses)
Harness/fuses/switches
System always comes up in in-line
diagnostic mode Symptom Troubleshooting
(see page 23-347)
Navigation system will not accept
security code Symptom Troubleshooting
(see page 23-353)The wrong color DVD is installed
Navigation frequently asks for anti-
theft code and/or needs GPS
initialization Symptom Troubleshooting
(see page 23-350)
Loss of voltage or poor ground
(G504, G505)
Navigation unit
Low battery voltage
Harness/fuses/switches
GPS icon is white or not shown Symptom Troubleshooting (see page 23-341) Navigation unit
Aftermarket accessories
connected to the system
The wrong color DVD is installed
The DVD is damaged or dirty
GPS antenna/cable
Harness/fuses/switches
Vehicle icon wanders across the
map when driving (does not follow a
displayed road) or map or vehicle
ICON spins Symptom Troubleshooting
(see page 23-345)
Navigation unit
GPS antenna/cable
ECM/PCM (speed signal)
No picture is displayed Symptom Tr oubleshooting
(see page 23-338) Navigation unit
The wrong color DVD is installed
The DVD is damaged or dirty
Harness/fuses/switches
Picture has lines/rolls/other issues
or is an odd color Symptom Troubleshooting
(see page 23-339) Navigation unit
The wrong color DVD is installed
The DVD is damaged or dirty
Aftermarket accessories
connected to the system
Harness/fuses/switches
Display day/night mode does not
work or does not work properly If you use the display mode
button, the auto day/night
function is disabled until you turn
the ignition switch to ON (II)
Symptom Troubleshooting
(see page 23-348)Display brightness set to High in
day or night mode
Gauge control module
The wrong color DVD is installed
The DVD is damaged or dirty
Harness/fuses/switches
System locks up or freezes
constantly Symptom Troubleshooting
(see page 23-348) Navigation unit
The wrong color DVD is installed
The DVD is damaged or dirty
Harness/fuses/switches
08/08/21 14:15:41 61SNR030_230_0279
ProCarManuals.com
DYNOMITE -2009-

SymptomDiagnostic procedure Also check for
23-277

















 







Voice guidance cannot be heard, is
broken up, or there is static
Symptom Troubleshooting
(see page 23-341) Volume or voice feedback setting
(see Owner’s manual)
Navigation unit
Stereo amplifier
Harness/fuses/switches
Voice control does not work/
respond Symptom Troubleshooting
(see page 23-342) Navigation unit
The wrong color DVD is installed
The DVD is damaged or dirty
Microphone harness/switches
HandsFreeLink control unit
Navigation cannot control HVAC by
voice command Symptom Troubleshooting
(see page 23-346) The wrong color DVD is installed
Harness/fuses/switches
Wrong navigation unit (model
code)
Navigation cannot control XM radio Symptom Troubleshooting (see page 23-350)Low or weak battery
Navigation cannot control audio
system Symptom Troubleshooting
(see page 23-349)Wrong color DVD
Navigation display buttons do not
work or respond properly Symptom Troubleshooting
(see page 23-340) Navigation unit
Open/short between the XM
receiver or the GA-Net bus
The wrong color DVD is installed
The DVD is damaged or dirty
Today’s Destinations button is dim
and not selectable in the Enter
destination by screen (grayed-out) The client has not entered a group
of locations for Today’s Destinations.
This is normal. The button is only
selectable if the client is using this
functionSee Owner’s Manual
Some set-up and information
functions of the navigation system
are grayed-out and do not work Client did not select OK from
Disclaimer screen. Refer to System
Function Diagram (see page 23-289)
Previous Destinations button is dim
and not selectable in the Enter
destination by screen (grayed-out) The vehicle may be new, or the
customer deleted the destination.
Enter a destination, and allow the
system to route to it. After the trip,
the Previous Destinations button
will be selectable
Address cannot be found or system
gives poor routing Verify proper operation and
system limitations using the
owner’s manual.
See Answering client question
Navigation coverage in general
troubleshooting
Refer to Database limitation in the
navigation system manual to
report database errorsDatabase limitations (address not
in database)
The wrong color DVD is installed
OPEN/CLOSE function of the display
does not work Symptom Troubleshooting
(see page 23-351) Navigation unit
Harness
Navigation display will not close Symptom Troubleshooting (see page 23-352) Navigation unit
Harness
Navigation display does not open or
opens part way Symptom Troubleshooting
(see page 23-352) Navigation unit
Harness
(cont’d)
08/08/21 14:15:41 61SNR030_230_0280
ProCarManuals.com
DYNOMITE -2009-

µ
´µ
´ ´
Î
Navigation Unit Inputs and Outputs for Connector A (24P)
Navigation Unit Connector A (24P) TerminalNumber Wire Color Terminal Name Description Voltage (about) Symptom
23-291
1 RED ILL ( )
Ground for
illumination light With full dash
lights brightness,
0VIf open: When brightness = Auto, night mode for the
display is inoperative when lights on.
If short to ground: No change to display.
12 BLK RADIO GND (Ground)Ground for display
unit 0 V
If open: No change to display.
If short to ground: No change to display.
13 GRY ILL ( ) (Illumination
positive)Parking light on
signal from dash
and console lights Light on =
battery voltage,
Lights off = 0 VIf open: When brightness = Auto, night mode for the
display is inoperative when lights on.
If short to ground: Blows fuse No. 14 (7.5 A) in
under-dash fuse/relay box.
15 BLU VSP (Vehicle speed
pulse)Vehicle speed
pulse signal from
ECM/PCM Pulses 0 5 V:
Average 2.5 V,
when movingIf open: No vehicle speed pulses.
Diagnostic screen Car Status, VSP Navi = 0.
If short to ground: No vehicle speed pulses.
Diagnostic screen Car Status, VSP Navi = 0.
24 WHT B ( B power
source)Continuous power
source
Battery voltage If open: Screen completely off (no backlight visible).
If short to ground: Blows fuse No. 23 (10 A) in the
under-hood fuse/relay box.
(cont’d)
Wire side of female terminals
08/08/21 14:15:46 61SNR030_230_0294
ProCarManuals.com
DYNOMITE -2009-

´µ
Î
Navigation Unit Inputs and Outputs for Connector C (8P)
Navigation Unit Connector C (8P)TerminalNumber Wire Color Terminal Name Description Voltage (about) Symptom
23-293
1 WHT B BACK UP Continuous power
sourceBattery voltage If open: Display picture goes out (display back light
still on). NOTE: System will reboot to enter code
screen.
If short to ground: Blows fuse No. 23 (10 A) in the
under-dash fuse/relay box.
4 BLK GND Ground for navigation unit0 V If open: No effect on system.
If short to ground: No effect on system.
7 BRN BACK LT Reverse signal of select laver from
Multiplex
integrated Control
unit (A/T) or
backup light switch
(M/T)In reverse,
battery voltage:
Otherwise0V
If open: Navigation never sees the reverse signal
and back-up camera does not come on when in
reverse. Diagnostic screen Car Status, Back = 0.
If short to ground: Blows fuse No. 10 (7.5 A) in the
under-dash fuse/relay box.
(cont’d)
Wire side of female terminals
08/08/21 14:15:46 61SNR030_230_0296
ProCarManuals.com
DYNOMITE -2009-

µµ
´µ
Î
Navigation Unit Inputs and Outputs for Connector D (12P)
Navigation Unit Connector D (12P) TerminalNumber Wire Color Terminal Name Description Voltage (about) Symptom
23-294Navigation System
System Description (cont’d)
1 GRN NAVI GUIDE Steering wheel
switch output45V
(navigation TALK
button pressed)
2.5 3 V
(navigation
BACK button
pressed)If open: Steering wheel navigation TALK, and
navigation BACK switch/buttons do not work.
If short to ground: Steering wheel navigation TALK,
and navigation BACK switch/buttons do not work.
5 YEL AC SI A/C input signal 0-battery voltage pulsesIf open: voice control does not work.
If short to ground: Voice control does not work.
6 RED AC SO A/C output signal 0-battery voltage pulsesIf open: A/C voice control does not work.
If short to ground: A/C voice control does not work.
7 BRN MIC GND Ground for microphone signal0 V If open: No microphone signal shown in
diagnostics: Navi System Link and Functional Set
up Mic Level.
If short to ground: No effect on voice recognition.
8 YEL MIC SIG Microphone output signal positive45V(with
navigation TALK
button pressed)If open: No microphone signal shown in diagnostic
screens: Navi System Link and Functional Setup
Mic Level.
If short to ground: No microphone signal shown in
diagnostic screens: Navi System Link and
Functional Setup Mic Level.
9 GRY MIC SHIELD Shield for terminal No.7,80 V If open: No effect on voice recognition.
If short to ground: No effect on voice recognition.
12 BLU AC CK Time set sync signal0-battery voltage
pulsesIf open: A/C voice control does not work.
If short to ground: A/C voice control does not work.
: The shielded wires have a heat-shrunk tube insulating the outside of the wire. The color of the insulating tube, typically black or dark gray, may not match the color of the wire listed on the schematic.
Wire side of female terminals
08/08/21 14:15:46 61SNR030_230_0297
ProCarManuals.com
DYNOMITE -2009-

Î
(#'#
)
´µ
´ ´
µ
´
µ ´
´µ´
µ´
´
µ ´
µ
23-296Navigation System
Circuit Diagram
A10 A9
BRN10
BRN
3 CABLE REEL
A5 A29
D1 CABLE REEL GRN
RED/BLK
BACKTALK
5
GRY
GPS
H1
H2
VSP BLU
A15
PNK BLU NAVIGATION UNIT
HFL-VOICE CONTROL SWITCH
8
GRN 680
10 k
2.2 k
GPS
ANTENNA
No. 14 (7.5 A) FUSE
(In the under-dash
fuse/relay box) DASH LIGHTS
BRIGHTNESS
CONTROLLER
AUDIO
REMOTE
GND VSP
GPS
XM
RECEIVER A3BRN K-LINE
MICU
A14
PUR
Q14 Q4
GRNA4
A3
LT BLU
Q8 Q1
WHT
WHT
UNDER-DASH FUSE/RELAY BOX A1
A13
A24 C1
C7
WHT B
BACK UP
BACK
LT
B
BACK UP
SCTY
RADIO
ACC
RADIO
G2 RED
GRY
ILL
ILL
RED
ORN ACC HOT in ACC (I)
and ON (II)
ACC
BAT
IGNITION
SWITCH
C2
WHT
BRN
No. 23
(10 A)
UNDER-HOOD FUSE/RELAY BOX
BATTERY
H1
D4 No. 2
(IG)
(50 A)
E15
No. 35
(7.5 A) No.14(7.5A)FUSE
(In the under-dash
fuse/relay box)
DASH LIGHTS
BRIGHTNESS
CONTROLLER
GPS
SH
GA-NET
BUS
GA-NET
BUS
GA-NET
BUS SH *:
The shielded wires have a heat-shrunk tube
insulating the outside of the wire. The color
of the insulating tube, typically black or dark gray,
may not match the color of the wire listed on the
schematic.
:GA-NET
:Shielding
28 27
D9
RED
D7 D8
GRN
MIC
GND MIC
SIG MIC
SIG
MIC
GND
MIC
SH MIC MIC
21
GRY BRN YEL
14 13
12
MIC SH MIC MIC
GRY
B10 8
HFL/NAVI
COMM SH
GRY GRY
B24 RED 7
21 20
GRN
B11
B23
BLK HFL/NAVI
COMM1
HFL/NAVI
COMM2
HFL/NAVI
COMM3
B12 WHT 6
HFL/NAVI
COMM4
HFL
SWITCH
A10 A9
BRNE3
E10
PNK BLU E9
USB
ADAPTER
UNIT A3BRN
GA-NET
BUS
GA-NET
BUS
GA-NET
BUS SH GA-NET
BUS
GA-NET
BUS
GA-NET
BUS SH
PNK BLU
A12
G504
G505 BLK
BLK
GND RADIO
GNDHFL/NAVI
COMM1
HFL/NAVI
COMM2
HFL/NAVI
COMM3
HFL/NAVI
COMM4 HFL/NAVI
COMM SH
NAVI
GUIDE
No. 1 (BAT) (100 A)
ECM/PCM
(VEHICLE
SPEED SIGNAL)
YEL AC
SI
RED AC
SO
CLIMATE
CONTROL
UNIT
BLUAC
CLK
D5
D6
D12
C4 ORN
MOONROOF
SWITCH MIC
ADPTHFL-NAVIGATION
MICROPHONE
3
* *
*
**
*
*
08/08/21 14:15:47 61SNR030_230_0299
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'#
)
Start-up procedure and Diagnostic Menu System Links
23-297
System Diagnostic Mode
Return System LinksHelp
Exit Diag
ReturnReturn
Navi.ECUSelect Diagnosis Items Self- Diagnosis Mode
Detail Information & Setting
(Navi will check internal function. connections, etc.
Perform this test with vehicle stopped and engine running.)
(Individual Diagnostic screens to confirma specific diagnostic screen.)
XM
Error
History
Yaw
Sensor Car Status
ECU Info. Hard Key
DVD Mic
HFL
Press any icon if you want to see details. GPS Ant. R. Camera
Display Radio
A/C
Start the vehicle, and at the disclaimer screen use the
navigation display hard buttons as described below:
Make sure the battery is in good condition, then press
and hold the three buttons MAP/GUIDE, MENU, and
CANCEL, for about 3 seconds. The display screen goes
directly to the Select Diagnosis Items menu shown
below.
 Self-Diagnosis Mode (runs the automatic diagnosis of the navigation system)
 Detail Information & Setting (allows you to manually diagnose the navigation system) 1. By selecting Self-Diagnosis Mode from the
navigation screen main menu. The message at the
bottom of the screen flashes indicating the
diagnostic is running. Make sure you enter the
audio anti-theft code.
NOTE: The system cannot complete a full diagnosis unless the engine is running.
 DTC 2703 can be stored when the ignition switch is at ACCESSORY (I). With the ignition switch is
in ACCESSORY (I), the climate control unit is
turned off and the navigation unit loses
communication and stores DTCs. Therefore,
there is a possibility that the system is normal
even DTC 2703 is stored. Check system links with
the engine running, and if it shows normal, the
system is OK at this time.
2. Select the icon you want to diagnose. Push in the select the icon to see the details of that diagnostic
function.
(cont’d)
08/08/21 14:15:48 61SNR030_230_0300
ProCarManuals.com
DYNOMITE -2009-

µ
Î
Î
Factory diagnostic screen In Line DiagDetailed Information & Settings
23-301
In Line Diag
123
456
789
0 Return
Navi ECU
Display XXXXCorrect PIN
GPS Antenna
RR Camera RadioXM
HFL A/C
Exit Diag
Start Diag
BACK
Delete Done
KA
Select Diagnosis Items
Self- Diagnosis Mode
Detail Information & Setting
(Navi will check internal function. connections, etc.
Perform this test with vehicle stopped and engine running.)
(Individual Diagnostic screens to confirma specific diagnostic screen.)
NOTE: If the vehicle left the factory in the factory
diagnostic mode, or if the navigation unit is replaced
you will see this screen every time you turn on the
ignition.
When a navigation unit is powered up for the first time
at the factory or after replacement with a new or
remanufactured navigation unit, the factory diagnosis
screen (In Line Diag) appears. Normally the factory
does the steps necessary to verify proper operation and
terminate the factory diagnostic.
Until the proper confirmation sequence is done, the
screen appears every time the vehicle is started.
Follow the steps below to prevent the screen from
showingupinthefuture:
 Press and hold the buttons (MENU, MAP/GUIDE, and CANCEL) for about 3 seconds. The Select Diagnosis
items screen appears.
 Press and hold the MAP/GUIDE button for 5 10 seconds. A screen with a Complete button,
appears.
 Press complete, then Return, and then shut the key off for 5 seconds. Do not disconnect the battery
during this period as the unit is saving the setting to
the SRAM memory. The In Line Diag should not
appear again.
 Restart the vehicle, and confirm normal operation by completing the TQI of the Navigation System Service
Bulletin. These section allows you to run a specific diagnostic
and allows additional setting choices for some screens
that are not shown when selecting an icon from the
System Links screen.
When you select the menu item Detail Information &
Setting menu, the main diagnosis menu is displayed.
(cont’d)
08/08/21 14:16:39 61SNR030_230_0304
ProCarManuals.com
DYNOMITE -2009-