lock ACURA CSX 2006 Service Manual PDF





6-63
A
B
B50 mm (2.0 in.)
45 mm (1.8 in.)
A
FIRST STEP
SECOND STEP
THIRD STEP
(New bolt)
4. Set the crankshaft to top dead center (TDC). Align
the TDC mark (A) on the crankshaft sprocket with
the pointer (B) on the engine block.
5. Set the camshaft pulley to TDC (see step 2 on page 6-21).
6. Install the cylinder head on the engine block.
7. Measure the diameter of each cylinder head bolt at point A and point B.
8. If either diameter is less than 10.6 mm (0.42 in.), replace the cylinder head bolt. 9. Apply new engine oil to the threads and under the
bolt heads of all cylinder head bolts.
10. Tighten the cylinder head bolts in sequence to 39 N·m (4.0 kgf·m, 29 lbf·ft). Use a beam-type
torque wrench. When using a preset click-type
torque wrench, be sure to tighten slowly and do not
overtighten. If a bolt makes any noise while you are
torquing it, loosen the bolt and retighten it from the
first step.
11. After torquing, tighten all cylinder head bolts in two steps (90 ° per step) using the sequence shown in
step 10. If you are using a new cylinder head bolt,
tighten the bolt an extra 90 °.
NOTE: Remove the cylinder head bolt if you
tightened it beyond the specified angle, and go
back to step 6 of the procedure. Do not loosen it
back to the specified angle.
(cont’d)
08/08/21 14:28:42 61SNR030_060_0063
ProCarManuals.com
DYNOMITE -2009-

(#'
/)
Engine Mechanical
Engine Block
........................................................................................................
................................................................. .....................
.....................
.......................................................... .................................
................................................. .......................................
.................................................. ........
............................................
........................................................ .................................
................................................
......................................................
................................................... ..............................................
................................................................
........................................
................................................................. .....................
.....................
.......................................................... .................................
................................................. .......................................
.................................................. ........
............................................
........................................................ .................................
................................................
......................................................
................................................... ..............................................
Special Tools
. 7-2
Component Location Index . 7-3
Connecting Rod and Crankshaft End Play Inspection . 7-5
Crankshaft Main Bearing Replacement . 7-6
Connecting Rod Bearing Replacement . 7-8
Oil Pan Removal . 7-11
Crankshaft and Piston Removal . 7-13
Crankshaft Inspection . 7-15
Block and Piston Inspection . 7-16
Cylinder Bore Honing . 7-18
Piston, Pin, and Connecting Rod Replacement . 7-18
Piston Ring Replacement . 7-21
Piston Installation . 7-23
Connecting Rod Bolt Inspection . 7-25
Crankshaft Installation . 7-25
Oil Pan Installation . 7-29
Transmission End Crankshaft Oil Seal Installation - In Car . 7-32
Sealing Bolt Installation . 7-33
08/08/21 14:32:25 61SNR030_070_0001
ProCarManuals.com
DYNOMITE -2009-




(#'
%)Ref. No. Tool Number Description Qty
7-2
Engine Block
Special Tools
07ZAD-PNAA100
Oil Seal Driver Attachment 96 1
07746-0010700 Attachment, 24 x 26 mm 1
07749-0010000 Driver 1
08/08/21 14:32:25 61SNR030_070_0002
ProCarManuals.com
DYNOMITE -2009-

Î
(#'
)
7-3
Component Location Index
MAIN BEARINGSDOWEL PINS LOWER BLOCK
BAFFLE PLATE
CRANKSHAFT CRANKSHAFT OIL SEAL,
TRANSMISSION END
BAFFLE PLATE
DRIVE PLATE (A/T model)
THRUST WASHERS FLYWHEEL (M/T model)
(cont’d)
Oil Clearance Inspection,
page 7-6
Selection, page 7-7
End Play Inspection, page 7-5
Removal, page 7-13
Inspection, page 7-15
Installation, page 7-25
Installation, step 24 on page 7-27
Installation - in Car, page 7-32
08/08/21 14:32:28 61SNR030_070_0003
ProCarManuals.com
DYNOMITE -2009-

Î
7-4Engine Block
Component Location Index (cont’d)
PISTON RINGS
PISTON PIN
CONNECTING ROD
CONNECTING ROD
BEARINGS CONNECTING ROD
BEARING CAP
PISTON
ENGINE BLOCK
CONNECTING ROD BOLTS DOWEL PINSReplacement, page 7-21
Removal, page 7-18
Inspection, page 7-19
Installation, page 7-20
End Play Inspection, page 7-5
Small End Measurement, page 7-19
Oil Clearance Inspection,page 7-8
Selection, page 7-9
Removal, page 7-13
Measurement, page 7-16
Installation, page 7-23
RidgeRemoval,step15onpage7-14
Cylinder Bore Inspection, page 7-16
Warpage Inspection, page 7-16
Cylinder Bore Honing, page 7-18
Inspection, page 7-25
08/08/21 14:32:31 61SNR030_070_0004
ProCarManuals.com
DYNOMITE -2009-

´

(#'


 )
µ
µ
µ µ
Main Bearing Clearance Inspection
Main Bearing-to-Journal Oil Clearance
No.1,2,4,5Journals:
Standard (New): 0.017 0.041 mm (0.0007 0.0016 in.)
Service Limit: 0.050 mm (0.0020 in.)
No. 3 Journal:
Standard (New): 0.025 0.049 mm (0.0010 0.0019 in.)
Service Limit: 0.055 mm (0.0022 in.)
7-6 Engine Block
Crankshaft Main Bearing Replacement
1. To check the main bearing-to-journal oil clearance,
remove the lower block and the bearing halves
(see page 7-13).
2. Clean each main journal and bearing half with a clean shop towel.
3. Place one strip of plastigage across each main journal.
4. Reinstall the bearings and lower block, then tighten the bolts to 29 N·m (3.0 kgf·m, 22 lbf·ft) 56 ° in
thepropersequence(seestep19onpage7-27).
NOTE: Apply new engine oil to the bolt threads and flanges.
 Do not rotate the crankshaft during inspection.
5. Remove the lower block and the bearings again, and measure the widest part of the plastigage. 6. If the plastigage measures too wide or too narrow,
remove the crankshaft, and remove the upper half
of the bearing. Install a new, complete bearing with
the appropriate color code(s), and recheck the
clearance. Do not file, shim, or scrape the bearings
or the caps to adjust clearance.
7. If the plastigage shows the clearance is still incorrect, try the next larger or smaller bearing (the
color listed above or below the current one), and
check again. If the proper clearance cannot be
obtained by using the appropriate larger or smaller
bearings, replace the crankshaft, and start over.
08/08/21 14:32:32 61SNR030_070_0006
ProCarManuals.com
DYNOMITE -2009-



Main Bearing Selection
Crankshaft Bore Code Location
Main Journal Code Location
7-7
No. 1 JOURNAL
(PULLEY END)
No. 5 JOURNAL
(TRANSMISSION END)
No. 1 JOURNAL No. 5 JOURNAL
1. Numbers, letters or bars have been stamped on theend of the engine block as a code for the size of
each of the five main journal bores. Write down the
crank bore codes.
If you cannot read the codes because of
accumulated dirt and dust, do not scrub them with
a wire brush or scraper. Clean them only with
solvent or detergent. 2. The main journal codes are stamped on the
crankshaft in either location.
(cont’d)
08/08/21 14:32:32 61SNR030_070_0007
ProCarManuals.com
DYNOMITE -2009-

´´

(#'



 ) µ
µ
µ µ
Connecting Rod Bearing Clearance
Inspection
Connecting Rod Bearing-to-Journal Oil Clearance
K20Z2 engine
Standard (New): 0.020 0.050 mm (0.0008 0.0020 in.)
Service Limit: 0.060 mm (0.0024 in.)
K20Z3 engine
Standard (New): 0.032 0.066 mm (0.0013 0.0026 in.)
Service Limit: 0.077 mm (0.0030 in.)
7-87-8 Engine Block
Crankshaft Main Bearing
Replacement (cont’d)
Connecting Rod Bearing
Replacement
Larger crank bore
1or
AorI 2or
BorII 3or
C or III4or
D or IIII
Smaller bearing (Thicker)
Blue
Pink
Yellow Green
Green/
Brown
Brown Green
Green/
Brown
Brown Green
Green/
Brown
Brown Green
Green/
Brown
Brown
Black Black/
Blue
Crank
bore
code
Pink/
YellowYellow
Yellow
Pink/
Yellow
Black
Black Black/
Blue
Main
journal
code
1
2
3
4
5
6
Smaller
main
journal Smaller
bearing
(Thicker)
3. Use the crank bore codes and crank journal codes
to select the appropriate replacement bearings
from the following table.
NOTE: Color code is on the edge of the bearing.
 When using bearing halves of different colors, it does not matter which color is used in the top or
bottom. 1. Remove the oil pump (see page 8-16).
2. Remove the baffle plates (see step 8 on page 7-13).
3. Remove the connecting rod cap and the bearing
half.
4. Clean the crankshaft rod journal and the bearing half with a clean shop towel.
5. Place plastigage across the rod journal.
6. Reinstall the bearing half and connecting rod cap, and tighten the bolts to 20 N·m (2.0 kgf·m, 14 lbf·ft)90 ° (K20Z2 engine) or 29 N·m (3.0 kgf·m,
22 lbf·ft) 90 ° (K20Z3 engine).
NOTE:  Apply new engine oil to the bolt threads and flanges.
 Do not rotate the crankshaft during inspection.
7. Remove the connecting rod cap and the bearing half, and measure the widest part of the plastigage.
08/08/21 14:32:33 61SNR030_070_0008
ProCarManuals.com
DYNOMITE -2009-



Connecting Rod Journal Code Location
7-10 Engine Block
Connecting Rod Bearing Replacement (cont’d)
No. 1 JOURNAL
No. 4 JOURNAL Larger big end bore
Smaller bearing (Thicker)
1orI 2orII
3orIII 4orIIII
Big end
bore
code
Smaller
rod
journal Smaller
bearing
(Thicker)
Rod
journal
code
Green/
BrownBlack
Yellow/
Green
Brown
Pink/
Yellow
Green
Brown Blue
Yellow Pink
Green Brown/
Black Brown/
Black
Green/
Brown
Yellow/
Green
Black/
Blue
A
B
C
D
3. The connecting rod journal codes are stamped on the crankshaft in either location. 4. Use the big end bore codes and rod journal codes
to select the appropriate replacement bearings
from the following table.
NOTE: Color code is on the edge of the bearing.
 When using bearing halves of different colors, it does not matter which color is used in the top or
bottom.
08/08/21 14:32:34 61SNR030_070_0010
ProCarManuals.com
DYNOMITE -2009-




7-12Engine Block
Oil Pan Removal (cont’d)
B
A
19. A/T model: Remove the shift cable cover.
20. K20Z2 engine: Remove the torque converter cover/clutch cover. 21. K20Z3 engine: Remove the clutch cover (A) and the
transmission mounting bolts (B).
22. Remove the bolts securing the oil pan.
23. Using a flat blade screwdriver, separate the oil pan from the lower block in the places shown.
24. Remove the oil pan.
08/08/21 14:32:35 61SNR030_070_0012
ProCarManuals.com
DYNOMITE -2009-