lock ACURA CSX 2006 Service Owner's Manual

ÃŽ
(#'


 )


(#'

")
Special Tools Required
Special Tools Required
4-314-31
Drive Belt ReplacementDrive Belt Auto-tensioner
Inspection
YA9317
A B
A
YA9317
Belt tension release tool Snap-on YA9317 or equivalent,
commercially available
1. Move the auto-tensioner (A) using the belt tension release tool to relieve tension from the drive belt
(B), then remove the drive belt.
2. Install the new drive belt in the reverse order of removal. Belt tension release tool Snap-on YA9317 or equivalent,
commercially available
1. Turn the ignition switch to ON (II), and make sure the A/C switch is OFF, then turn the ignition switch
to LOCK (0).
2. Check the position of the auto-tensioner indicator’s pointer (A). Start the engine then check the position
again with the engine idling. If the position of the
indicator moves or fluctuates very much, replace
the auto-tensioner (see page 4-32).
3. Check for abnormal noise from the tensioner pulley. If you hear abnormal noise, replace the tensioner
pulley(seepage4-33).
4. Remove the drive belt (see page 4-31).
5. Move the auto-tensioner within its limit using the belt tension release tool in the direction shown.
Check that the tensioner moves smoothly and
without any abnormal noise. If the tensioner does
not move smoothly, or you hear abnormal noise,
replace the auto-tensioner (see page 4-32).
(cont’d)
08/08/21 14:10:13 61SNR030_040_0032
ProCarManuals.com
DYNOMITE -2009-

ÃŽ
(#'



!)
Exploded View
4-38Charging System
Alternator Overhaul
ROTOR
FRONT BEARING
RETAINERFRONT BEARING
DRIVE-END
HOUSING
PULLEYPULLEY
LOCKNUT
TERMINAL
INSULATOR BRUSH HOLDER
ASSEMBLY REAR HOUSING
ASSEMBLY
END COVER WASHER
08/08/21 14:10:17 61SNR030_040_0039
ProCarManuals.com
DYNOMITE -2009-




Special Tools Required
4-39
B
A
 Driver 07749-0010000
 Attachment, 42 x 47 mm 07746-0010300
NOTE: Refer to the Exploded View as needed during
this procedure.1. Test the alternator and regulator before you remove them (see page 4-28).
2. Remove the alternator (see page 4-34).
3. If the front bearing needs replacing, remove the pulley locknut with a 10 mm wrench (A) and a
22 mm wrench (B). If necessary, use an impact
wrench.
4. Remove the harness stay and the three flange nuts from the alternator. 5. Remove the end cover.
6. Remove the brush holder assembly.
(cont’d)
08/08/21 14:10:18 61SNR030_040_0040
ProCarManuals.com
DYNOMITE -2009-




Alternator Reassembly
4-42Charging System
Alternator Overhaul (cont’d)
A
B
16. If you removed the pulley, put the rotor in the drive- end housing, then tighten its locknut to 110 N·m
(11.2 kgf·m, 81.0 lbf·ft).
17. Remove any grease or any oil from the slip rings.
18. Put the rear housing assembly and the drive-end housing/rotor assembly together, tighten the four
through bolts.
19. Push the brushes (A) in, then insert a pin or drill bit (B) (about 1.6 mm (0.06 in.) diameter) to hold them
there.
20. Install the brush holder assembly, and pull out the pin or drill bit.
21. Install the end cover.
22. After assembling the alternator, turn the pulley by hand to make sure the rotor turns smoothly and
without noise.
23. Install the alternator (see page 4-36) and the drive belt (see page 4-31).
08/08/21 14:10:46 61SNR030_040_0043
ProCarManuals.com
DYNOMITE -2009-


ÃŽ

5-20Engine Assembly
Engine Installation (cont’d)
D
A
B
10x1.25mm
59 N·m
(6.0 kgf·m, 43 lbf·ft)
C
10x1.25mm
54 N·m
(5.5 kgf·m, 40 lbf·ft)
A
B
C
10x1.25mm
59 N·m
(6.0 kgf·m, 43 lbf·ft)
D
10x1.25mm
54 N·m
(5.5 kgf·m, 40 lbf·ft)
10x1.25mm
38 N·m
(3.9 kgf·m, 28 lbf·ft)
E
F
A
D
B
B
C
10x1.25mm
33 N·m (3.4 kgf·m, 25 lbf·ft)
8x1.25mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
29. Install the stiffener (A), then tighten the steering gearbox mounting bolt (B) and the stiffener
mounting bolt (C).
30. Install the harness clamp (D) to the subframe.
31. Install the steering gearbox bracket (A).
32. Install the stiffener (B), then tighten the steering gearbox mounting bolt (C) and the stiffener
mounting bolt (D).
33. A/T model: Install the shift cable (see step 19 on page 14-245).
34. Install a new set ring on the end of each driveshaft, then install the driveshafts (see page 16-20). Make
sure each ring ‘‘clicks’’ into place in the differential
and the intermediate shaft. 35. Connect the lower arms to the knuckles (see step 9
on page 18-16).
36. Connect the stab ilizer links (see page 18-25).
37. Install the three way catalytic converter (TWC) (A). Use the new gaskets (B) and the new self-locking
nuts (C).
38. Connect the air fuel ratio (A/F) sensor connector (D).
39. Connect the secondary heated oxygen sensor (secondary HO2S) connector (E), then install the
grommet (F).
40. Install the splash shield.
Replace.
Replace.
Replace.
08/08/21 14:20:34 61SNR030_050_0020
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
 M/T model
A/T model
5-245-24
Engine Assembly
Engine Installation (cont’d)
Side Engine Mount Replacement
67. Refill the transmission with fluid:
 Manual transmission (see step 3 on page 13-5)
 Automatic transmission (see step 3 on page14-232)
68. A/T model: Move the shift lever to each gear, and verify that the A/T gear position indicator follows
the transmission range switch.
69. M/T model: Check that the transmission shifts into gear smoothly.
70. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
71. Do the ECM/PCM reset procedure (see page 11-4).
72. Do the crankshaft position (CKP) pattern clear/CKP pattern learn procedure (see page 11-4).
73. Inspect the idle speed (see page 11-309).
74. Inspect the ignition timing (see page 4-20).
75. Check the wheel alignment (see page 18-5). 1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:01 61SNR030_050_0024
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
 M/T model
A/T model
5-245-24
Engine Assembly
Engine Installation (cont’d)
Side Engine Mount Replacement
67. Refill the transmission with fluid:
 Manual transmission (see step 3 on page 13-5)
 Automatic transmission (see step 3 on page14-232)
68. A/T model: Move the shift lever to each gear, and verify that the A/T gear position indicator follows
the transmission range switch.
69. M/T model: Check that the transmission shifts into gear smoothly.
70. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
71. Do the ECM/PCM reset procedure (see page 11-4).
72. Do the crankshaft position (CKP) pattern clear/CKP pattern learn procedure (see page 11-4).
73. Inspect the idle speed (see page 11-309).
74. Inspect the ignition timing (see page 4-20).
75. Check the wheel alignment (see page 18-5). 1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:01 61SNR030_050_0024
ProCarManuals.com
DYNOMITE -2009-



(#'
 ) M/T model
A/T model
5-355-35
Side Engine Mount Bracket
Replacement
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
7. Raise the vehicle on the lift.
8. M/T model: Tighten the front mount mounting bolt.
9. Install the splash shield (see step 40 on page 5-20).
1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
(cont’d)
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:08 61SNR030_050_0035
ProCarManuals.com
DYNOMITE -2009-



(#'
 ) M/T model
A/T model
5-355-35
Side Engine Mount Bracket
Replacement
12x1.25mm
64 N·m
(6.5 kgf·m, 47 lbf·ft)
7. Raise the vehicle on the lift.
8. M/T model: Tighten the front mount mounting bolt.
9. Install the splash shield (see step 40 on page 5-20).
1. Support the engine with a jack and wood block
under the oil pan.
2. Remove the upper torque rod.
(cont’d)
Replace.
Replace.
Replace.
Replace.
08/08/21 14:21:08 61SNR030_050_0035
ProCarManuals.com
DYNOMITE -2009-

















(#'
%)Ref. No. Tool Number Description Qty
6-2
Cylinder Head
Special Tools
07AAB-RWCA120
Camshaft Lock Pin Set 1
07AAJ-PNAA101 Air Pressure Regulator 1
07HAH-PJ7A100 Valve Guide Reamer, 5.5 mm 1
07JAA-001020A Socket, 19 mm 1
07JAB-001020A Holder Handle 1
07MAA-PR70110 Adjuster 1
07MAA-PR70120 Locknut Wrench 1
07NAB-001040A Holder Attachment, 50 mm 1
07PAD-0010000 Stem Seal Driver 1
07ZAJ-PNAA101 VTEC Air Adapter 2
07ZAJ-PNAA200 VTEC Air Stopper 1
07ZAJ-PNAA300 Air Joint Adapter 1
07742-0010100 Valve Guide Driver, 5.5 mm 1
07746-0010400 Attachment, 52 x 55 mm 1
07749-0010000 Driver 1
07757-PJ1010A Valve Spring Compressor Attachment 1
08/08/21 14:26:14 61SNR030_060_0002
ProCarManuals.com
DYNOMITE -2009-