ignition ACURA CSX 2006 Service Manual PDF

Throttle Body
Brake Pedal Position Switch
Electrical Power Steering (EPS) Signal
Fuel Cutoff Control
Fuel Pump Control
PGM-FI Main Relay 1 and 2
Idle Control System
Fuel Supply System
11-36Fuel and Emissions Systems
System Description (cont’d)
THROTTLE VALVE
THROTTLE POSITION
(TP) SENSOR and
THROTTLE ACTUATOR
The throttle body is a single-barrel side draft type. The
lower portion of the throttle valve is heated by engine
coolant from the cylinder head to prevent icing of the
throttle plate. When the engine is cold, the A/C compressor is on, the
transmission is in gear, the brake pedal is pressed, the
power steering load is high, or the alternator is
charging, the ECM/PCM sends signal to the throttle
position to maintain the correct idle speed.
The brake pedal position switch signals the ECM/PCM
when the brake pedal is pressed.
The EPS signals the ECM/PCM when the power steering
load is high.
During deceleration with the throttle valve closed,
current to the injectors is cut off to improve fuel
economy at engine speeds over 1,000 rpm. Fuel cutoff
control also occurs when the engine speed exceeds
6,900 rpm (K20Z3: 8,200 rpm), regardless of the
position of the throttle valve, to protect the engine from
over-revving. When the vehicle is st
opped, the ECM/
PCM cuts the fuel at engine speeds over 5,000 rpm
(K20Z3: 7,700 rpm). On a cold engine, fuel cut occurs at
a lower engine speed.
When the ignition switch is turned to ON (II), the ECM/
PCM grounds PGM-FI main relay 2 (FUEL PUMP) which
feeds current to the fuel pump for 2 seconds to
pressurize the fuel system. With the engine running, the
ECM/PCM grounds PGM-FI main relay 2 (FUEL PUMP)
and feeds current to the fuel pump. When the engine is
not running and the ignition is turned to ON (II), the
ECM/PCM cuts ground to PGM-FI main relay 2 (FUEL
PUMP) which cuts current to the fuel pump.
PGM-FI main relay 1 is energized whenever the ignition
switch is ON (II), to supply battery voltage to the ECM/
PCM, power to the injectors, and power for PGM-FI
main relay 2 (FUEL PUMP). PGM-FI main relay 2 (FUEL
PUMP) is energized to supply power to the fuel pump
for 2 seconds when the ignition switch is turned to
ON (II), and when the engine is cranking or running.
08/08/21 14:13:39 61SNR030_110_0036
ProCarManuals.com
DYNOMITE -2009-

Î

Fuel Cap Warning MessageTo make the message go off (with the HDS)
To make the message go off (without the
HDS) (’06 model)
To make the message go off (without the
HDS) (’07-09 models)
First drive cycle Procedure
Procedure
Procedure
11-42Fuel and Emissions Systems
System Description (cont’d)
A
Shows CHECK FUEL CAP
in the gauge display.
The ECM/PCM detects a loose or missing fuel fill cap as
an evaporative system leak, and alarts the driver by
showing a warning message in the gauge display.
The first time a leak is detected a CHECK FUEL CAP
message is shown in the gauge display (A). To scroll to
another message, press the select/reset button. The
CHECK FUEL CAP message appears each time you
restart the engine until the system turns the message
off. Turn the engine off, then replace or tighten the fuel
fill cap until it clicks at least once.
1. Tighten the fuel fill cap until it clicks.
2. Clear the Temporary DTC with the HDS.
3. Verify there is no leak by doing the EVAP
FUNCTION TEST in the INSPECTION MENU with
the HDS.
1. Tighten the fuel fill cap until it clicks.
2. The message should go off after s everal days of
normal driving.
1. Tighten the fuel fill cap until it clicks.
2. Start the engine, then turn the ignition switch to LOCK (0).
3. Repeat step 2 two more times.
08/08/21 14:13:43 61SNR030_110_0042
ProCarManuals.com
DYNOMITE -2009-

Î

11-49
EVAP CANISTER
PURGE VALVE
BLK/YEL
B3
LBLK/YEL
No. 1 IGNITION COILNo. 3 IGNITION COIL
C15
C16
C17
G101BLK BLK
BLK/WHT
BLK
ICM To
SPARK
PLUG
ICM
To
SPARK
PLUG
ICM
To
SPARK
PLUG
No. 2 IGNITION COIL
17
WHT/BLU
BLU/RED
No. 4 IGNITION COIL
C18
BLKICM To
SPARK
PLUG
24P JUNCTION
CONNECTOR
24P JUNCTION
CONNECTOR
BLK
M
BLK/
WHT BLK/YEL
B42
YEL/GRN BLK/WHT
BLK/WHT
BRN BLK/WHT
WHT/BLU
ALTERNATOR
1
1
3
YEL/BLU
BLK/YEL
G
WHT/BLU
9
B43 WHT/RED WHT/RED
WHT/GRN
B41 WHT/GRN 4
1
3
5
YEL
C101
7
2
34
2
8
6 7
BLK/YEL
WHT/BLU
WHT/RED
WHT/GRN
PCS
IGPLS1
IGPLS2
IGPLS3
IGPLS4 ALTL
ALTF ALTC K
WHT/BLU
BLU/RED YEL/GRN
BRN
BLU
8 13
1415 16
1
2
3
1
2
3
1
2
3
1
2 YEL/BLU
2
BLK/YEL
C106
C101 15
16
(cont’d)
08/08/21 14:13:46 61SNR030_110_0049
ProCarManuals.com
DYNOMITE -2009-

Î
11-57
ETCS
CONTROL
RELAY
A/C COMPRESSOR
CLUTCH RELAY
ELD BATTERY
UNDER-HOOD FUSE/RELAY BOX
WHT
BRN D1
ORN D4
WHT D8
YEL A1
ORN A3
BLK A2
G301 GRY
PUR E6
BLU E7
ORN
E5
E1
LT BLU
C1
IG1ETCS 21
WHT P
M
A23
ELD U RED
F20
PNK
F16 F14
GRN
F9 F7
ORN
F6
YEL
F5
A14
ACC A21
SUBRLY A5
FANH A6
MRLY A4
FANL A8
IGP A20
ETCSRLY
ORN L
AD
AC AE
ABAA
Z PGM-FI
SUBRELAY
PGM-FI
MAIN
RELAY 1
IGNITION
COIL
RELAYA/C
CONDENSER
FAN RELAY
COOLING
FAN
CONTROL
RELAY
RADIATOR
FAN RELAY
9
10
ORN
ORN YEL/BLK
A
AH
F19
H1
C101 PUR
C101
PUR
G1
15
3
(cont’d)
08/08/21 14:13:52 61SNR030_110_0057
ProCarManuals.com
DYNOMITE -2009-

Î
´
ECM/PCM Circuit Diagram (K20Z2 engine) (cont’d)
11-58Fuel and Emissions Systems
System Description (cont’d)
Z
C36 IG1
A44 S-NET5V
A15
IMOFPR
A31
SCS
A40
BKSW BLK/GRN
C101 2
MICU
V
PGM-FI MAIN
RELAY 2
(FUEL PUMP)
UNDER-DASH FUSE/RELAY BOX
F5
YEL
F8
PNK
F10
BRN
F11
BRN
F24
BRN
F25
LT GRN
F30
LT GRN
F31
WHT
F29
G2
ORN
G4
ORN
BRN
G16
WHT
G20
WHT
Q1
WHT
Q5
ORN
Q8
LT BLU
E9
GRN
E27
YEL
IG2
B IG1
D1
WHT
D2
BLU
C3
ORN
C1
YEL
3
AD
ST
AC
AB
O
ORN
AE
AA
YW
X
ST6
4
1
R
IGNITION SWITCH FUEL PUMPP
2
4
BLK E28
G601
IG1 HOT in ON (II)
and START (III) YEL
G12 STARTER
CUT RELAY
(ST CUT)
22
UNDER-HOOD FUSE/RELAY BOX: No. 21 DBW (THROTTLE
ACTUATOR CONTROL) (15 A) No. 18 IG COIL (15 A)
No.19FIMAIN(15A)
No.11FISUB(15A)
No.15OILLVL(7.5A)
No. 2 IG MAIN (50 A)
No. 23 BACK UP (10 A)
No.12STOP&HORN(15A)
No. 1 MAIN FUSE (100 A)
UNDER-DASH FUSE/RELAY BOX: No. 3 ALTERNATOR (10 A)
No. 2 FUEL PUMP (15 A)
No. 36 IG2 HAC (A/C) (10 A)
No. 10 METER (7.5 A)
08/08/21 14:13:53 61SNR030_110_0058
ProCarManuals.com
DYNOMITE -2009-

ÎECM Circuit Diagram (K20Z3 engine) (cont’d)
11-62Fuel and Emissions Systems
System Description (cont’d)
EVAP CANISTER
PURGE VALVE
BLK/YEL
B3
IBLK/YEL
BLK/YEL
No. 1 IGNITION COILNo. 3 IGNITION COIL
C15
C16
C17
G101BLK BLK
BLK/WHT
BLK
ICM To
SPARK
PLUG
ICM
To
SPARK
PLUG
ICM
To
SPARK
PLUG
No. 2 IGNITION COIL
17
WHT/BLU BLU/RED No. 4 IGNITION COIL
C18
BLKICM To
SPARK
PLUG
24P JUNCTION
CONNECTOR
24P JUNCTION
CONNECTOR
BLK
J
BLK/
WHT BLK/YEL
B42
YEL/GRN BLK/WHT
BLK/WHT
BRN BLK/WHT
WHT/BLU
ALTERNATOR
1
1
3
YEL/BLU
BLK/YEL
D
WHT/BLU
C106
9
B43 WHT/RED WHT/RED
WHT/GRN
B41 WHT/GRN 4
6
1
3
5
YEL C101
7
2
34
2
8
6 7
BLK/YEL
WHT/BLU
WHT/RED
WHT/GRN
PCS
IGPLS1
IGPLS2
IGPLS3
IGPLS4 ALTL
ALTF ALTC H
WHT/BLU
BLU/RED YEL/GRN
BRN
BLU
8
C101
13
1415 16
1
2
3
1
2
3
1
2
3
1
2 YEL/BLU
REVERSE LOCKOUT
SOLENOID
GRN/BLK
1
2
BLK/YEL
A27
RVS
GRN 20
C101 2
4
15
16
08/08/21 14:15:27 61SNR030_110_0062
ProCarManuals.com
DYNOMITE -2009-

Î
11-67
ETCS
CONTROL
RELAY
A/C COMPRESSOR
CLUTCH RELAY
ELD BATTERY
UNDER-HOOD FUSE/RELAY BOX
WHT H1
BRN D1
ORN D4
WHT D8
YEL A1
ORN A3
BLK A2
G301 GRY
PUR E6
BLU E7
ORN
E5 E1
LT BLU
C1
IG1ETCS 21
C101
WHT K
J
A23
ELD Q RED
F20
PUR
F19
F16 F14
GRN
F9
F7
ORN
F6
YEL
F5
A14
ACC A21
SUBRLY A5
FANH A6
MRLY A4
FANL A8
IGP A20
ETCSRLY
ORN I
U
Y Z
XW
V N
PGM-FI
SUBRELAYPGM-FI
MAIN
RELAY 1
IGNITION
COIL
RELAYA/C
CONDENSER
FAN RELAY
COOLING
FAN
CONTROL
RELAY
RADIATOR
FAN RELAY
G1
9
10
ORN
ORN C101
YEL/BLK
A
PURPNK
15
3
(cont’d)
08/08/21 14:15:31 61SNR030_110_0067
ProCarManuals.com
DYNOMITE -2009-

Î
´
ECM Circuit Diagram (K20Z3 engine) (cont’d)
11-68Fuel and Emissions Systems
System Description (cont’d)
PGM-FI MAIN
RELAY 2
(FUEL PUMP)
UNDER-DASH FUSE/RELAY BOX
STARTER
CUT RELAY
(ST CUT)
F5
YEL
F8
PNK
F10
BRN
F11
BRN
F24
F25
LT GRN
F30
LT GRN
F31
WHT
F29
G2
ORN
G4
ORN
G12
BRN
G16
WHT
G20
WHT
Q1
WHT
Q5
ORN
Q8
LT BLU
E9
GRN
E27
YEL
IG2
B IG1
D1
WHT
D2
BLU
C3
ORN
C1
YEL
3 UOPY
V
X
C36 IG1
A44 S-NET5V
A15 IMOFPR
A31
SCS
A40
BKSW
G401 BLK/GRN
C101 2
BLK
TRS
ST6
4
1
M
IGNITION SWITCH MICU
FUEL PUMP P
2
4
BLK
1
2
CLUTCH
INTERLOCK
SWITCH ZW
Clutch pedal pressed: closed
Clutch pedal released: open
IG1 HOT in ON (II)
and START (III)
ORN
G601BRN
22
UNDER-HOOD FUSE/RELAY BOX:
No. 21 DBW (THROTTLE
ACTUATOR CONTROL) (15 A) No. 18 IG COIL (15 A)
No.19FIMAIN(15A)
No.11FISUB(15A)
No.15OILLVL(7.5A)
No. 2 IG MAIN (50 A)
No. 23 BACK UP (10 A)
No.12STOP&HORN(15A)
No. 1 MAIN FUSE (100 A)
UNDER-DASH FUSE/RELAY BOX: No. 3 ALTERNATOR (10 A)
No. 2 FUEL PUMP (15 A)
No. 36 IG2 HAC (A/C) (10 A)
08/08/21 14:15:32 61SNR030_110_0068
ProCarManuals.com
DYNOMITE -2009-

µµ
(#'

)
Malfunction Indicator Lamp (MIL) Indication
(In relation to Readiness Codes) Catalytic Converter Monitor and Readiness
Code
Enable Criteria
Procedure
11-69
How to Set Readiness Codes
The vehicle has certain readiness codes that are part of
the on-board diagnostics for the emissions systems. If
the vehicle’s battery has been disconnected or gone
dead, if the DTCs have been cleared, or if the ECM/PCM
has been reset, these readiness codes are reset to
incomplete. In some states, part of the emissions
testing is to make sure these codes are set to complete.
If all of them are not set to complete, the vehicle may
fail the emission test, or the test cannot be finished.
To check if the readiness codes are set to complete,
turn the ignition switch to ON (II), but do not start the
engine. The MIL will come on for 15 20 seconds. If it
then goes off, the readiness codes are set to complete.
If it flashes five times, one or more readiness codes are
not set to complete. To set readiness codes from
incomplete to complete, do the procedure for the
appropriate code.
To check the status of a specific DTC system, check the
OBD status in the DTC MENU with the HDS (see page
11-8). This screen displays the code, the current data list
of the enable criteria, and the status of the readiness
testing. NOTE:
 Do not turn the ignition switch to LOCK (0) or ACC (I) during the procedure.
 All readiness codes are cleared when the battery is disconnected, if the DTCs have been cleared, or if the
ECM/PCM is reset with the HDS.
 Low ambient temperatures or excessive stop-and-go traffic may increase the drive time needed to switch
the readiness code from incomplete to complete.
 The readiness code will not switch to complete until all the enable criteria are met.
 If a fault in the secondary HO2S system caused the MIL to come on, the readiness code cannot be set to
complete until you correct the fault.
 ECT SENSOR 1 at 70 °C (158 °F) or more.
 IAT SENSOR at 7 °C (20 °F) or more.
 Vehicle speed (VSS) above 40 km/h (25 mph). 1. Connect the HDS to the vehicle’s data link connector (DLC), and bring up the READINESS
CODEs screen for Catalyst in the DTCs MENU.
2. Start the engine.
3. Test-drive the vehicle under stop-and-go conditions with short periods of steady cruise. After about
8 km (5 miles), the readiness code should switch to
complete.
4. If the readiness code is still not set to complete, check for a Temporary DTC with the HDS. If there is
no DTC, one or more of the enable criteria were
probably not met; repeat the procedure.
(cont’d)
08/08/21 14:15:32 61SNR030_110_0069
ProCarManuals.com
DYNOMITE -2009-

Evaporative Emission (EVAP) Control
System Monitor and Readiness CodeAir Fuel Ratio (A/F) Sensor Monitor and
Readiness Code
Enable Criteria
Procedure Enable Criteria
Procedure
11-70Fuel and Emissions Systems
How to Set Readiness Codes (cont’d)
NOTE: All readiness codes are cleared when the battery
is disconnected, if the DTCs have been cleared, or if the
ECM/PCM is reset with the HDS.
 Battery voltage is more than 10.5 V.
 Engine at idle.
 ECT SENSOR 1 and ECT SENSOR 2 between 80 °C (176 °F) and 100 °C (212 °F).
 MAP SENSOR less than 46.6 kPa (350 mmHg, 14 in.Hg).
 Vehicle speed (VSS) 0 km/h (0 mph).
 IAT SENSOR between 0 °C (32 °F) and 100 °C (212 °F).
1. Connect the HDS to the DLC.
2. Start the engine.
3. Select EVAP TEST in the INSPECTION MENU with the HDS, then select the FUNCTION TEST in the
EVAP TEST MENU.
 If the result is normal, readiness is complete.
 If the result is not normal, go to the next step.
4. Check for a Temporary DTC. If there is no DTC, one or more of the enable criteria were probably not
met; repeat the procedure. NOTE:
 Do not turn the ignition switch to LOCK (0) or ACC (I) during the procedure.
 All readiness codes are cleared when the battery is disconnected, if the DTCs have been cleared, or if the
ECM/PCM is reset with the HDS.
ECT SENSOR 1 at 60 °C (140 °F) or more. 1. Start the engine.
2. Test-drive the vehicle under stop-and-go conditions with short periods of steady cruise. During the
drive, decelerate (with the throttle fully closed) for
5 seconds. After about 5.6 km (3.5 miles), the
readiness code should switch from incomplete to
complete.
3. Check the readiness codes screen for the air fuel ratio (A/F) sensor in the DTCs MENU with the HDS.
 If the screen shows complete, readiness is complete.
 If the screen shows not complete, go to the next step.
4. Check for a Temporary DTC. If there is no DTC, the enable criteria was probably not met. Select the
DATA LIST MENU. Check the ECT SENSOR 1 in the
ALL DATA LIST with the HDS. If the ECT SENSOR 1
is less than 60 °C (140 °F), run the engine until it is
more than 60 °C (140 °F), then repeat the procedure.
08/08/21 14:15:32 61SNR030_110_0070
ProCarManuals.com
DYNOMITE -2009-