Acura MDX 2007 Owner's Manual

Avoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.If it takes several pushes on the
button to lock or unlock the doors
and the tailgate, replace the battery
as soon as possible.
To replace the battery:Remove the screw at the base of
the transmitter with a small
Phillips-head screwdriver.
Separate the keypad from the
transmitter by pushing any button
f rom outside.
Battery type: CR1616
1.
2.
CONT INUED
Remote Transmitter CareReplacing the Transmitter
Battery
Remote Transmitter
Inst rument s and Cont rols
137
KEYPAD
SCREW
——y

y
()-y
y

µ
Remove the old battery and note
the polarity. Make sure the
polarity of the new battery is the
same ( side f acing up), then
insert it in the keypad.
An improperly disposed of battery
can hurt the environment.
Always conf irm local regulations
for battery disposal.
Snap the two halves of the keypad,
then install the parts in reverse
order.
Place a cloth on the edge of the
keypad, and remove the upper half
by caref ully prying on the edge
with a small f lat-tip screwdriver. 4.
5.
3.
As required by the FCC: This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Remote Transmitter
138
BATTERY
——y

y
()-y
y

Here are the settings activated with
the remote;
Driving position memory
(see page ).
When you unlock the driver’s door
with your remote, each remote
activates the keyless memory
settings related to that remote. The
driver’s ID (MEMORY 1 or
MEMORY 2) is shown on the back
of each remote. You
will also see the ‘‘WELCOME
DRIVER 1’’ or ‘‘WELCOME
DRIVER 2’’ message on the multi-
info rmation display, dep ending on
which linked remote transmitter is
used.
To turn off this feature, press and
hold the LOCK and UNLOCK
buttonsatthesametime.TheLED
in the remote will blink twice. Then
release the buttons. Doing this
cancels the keyless memory settings
for that remote and restores the
default settings.
To turn the keyless memory settings
back on, repeat this procedure. The
LED will blink once to indicate the
fe ature has been turned on.
The steering wheel will move to the
stored position when you insert the
key into the ignition switch.
When
you unlock and open the
driver’s door with the remote
transmitter, the driver’s seat (except
the power lumbar feature) and
outside mirrors start to move to the
positions stored in memory. The
indicator in the related memory
button to the remote comes on.
Audio
system settings
(see page ).
Climate control settings
(see page ).
Customized
settings
(see page ). 83
155 198 169
K eyless Memory Settings
Remote Transmitter
Inst rument s and Cont rols
139
TM
——y

y
()-y
y

µ
See pages for important safety
inf ormation and warnings about how to properly position seats and seat-backs. 12 14
The controls f or the power
adjustable front seats are on the
outside edge of each seat bottom.
You can adjust the seats with the
ignition switch in any position. Make
all seat adjustments bef ore you start
driving.
Moves the seat forward
and backward.
Raises or lowers the seat.
The passenger seat has the same
adjustments as the driver’s seat but
without any lumbar adjustment. Moves the whole seat up
and f orward, or down
and backward. The front
of the seat also tilts up or
down at the same time.
Adjusts the seat-back
angle f orward or
backward.
Increases or decreases
the lumbar support.
(Driver’s seat only)
Moves the f ront of the
seat up or down.
Seats
Front Seat Power A djustments
140
——y

y
()-y
y

See page for important safety
inf ormation and a warning about how to properly position the head restraints. 14
The f ront and the second row outer
head restraints adjust f or height.
The head restraints in the second
row center and third row seating
positions can be positioned in the
f ully lowered or f ully raised position.
You need both hands to adjust the
restraint. Do not attempt to adjust it
while driving. To raise it, pull upward.
To lower the restraint, push the
release button sideways, and push
the restraint down.
Theyaremosteffectivewhenyou
adjust them so the back of the
occupant’s head rests against the
center of the restraint. Your vehicle is equipped with head
restraints in all seating positions to
help protect you and your
passengers f rom whiplash and other
injuries.
To remove one f or cleaning or repair,
push the release button, and lift the
restraint up.
Make sure the head restraint locks
in position when you reinstall it.
CONT INUED
Head Restraints
Seats
Inst rument s and Cont rols
141
RELEASE BUTTON
FRONT
——y


y
()-y
y

When a passenger is seated in the
secondrowcenterorathirdrow
seating position, make sure the
center head restraint is properly
positioned.To change the seat-back angle of the
seats in the second row, pull up on
thehandleontheoutsideof theseat-
back, and push the seat-back.
Overall, the seat-back has six
dif f erent positions. To unlatch the detachable anchor
bef ore f olding the seat-back, insert
the latch plate into the slot on the
side of the anchor buckle and
allow the seat belt to retract. Store
the detachable anchor and seat
belt latch plates in the retractor
housing.
Reverse this procedure to return the
seat to the upright position. Make
sure the seat is locked securely
bef ore driving. Fold the seat-back forward. Pull up the handle on the outside
of the seat-back. Lower the head restraints to their
lowest positions.
The left and right halves can be
f olded separately.
2.
3. 1.
4. Folding the Second Seat
A djusting the Second Seat
Seats
142
HANDLE
SECOND CENTER AND THIRD ROW
RELEASE BUTTON
—

—y

y
()-y
y

To get into the third row seats, pull
uptheleveronthesideof the
passenger’s side second row seat-
back. The seat-back will tilt f orward,
and then can be slid forward.
After you return the seat-back to the
upright position, push the whole seat
backwards until it latches. Make
sure the seat is f ully latched bef ore
sitting in it.Use the latch plate to release the
seat belt from the detachable
anchor.
Lower the head restraints to their
lowest positions.
To f old the third row seat,
the second row seat-back must be
f olded down or completely up right.
Unlock the seat-back by pulling
the handle. Push the seat-back
forward.
Make sure the outer shoulder belts
are positioned on each hook
whenever the third seat is f olded.
1.
2.
3.
CONT INUED
T hird Row A ccessFolding the T hird Row Seat
Seats
Inst rument s and Cont rols
143
NOTE:
THIRD SEATHANDLE
RELEASE LEVER
——y

y
()-y
y

When the seats are returned to the
upright position, these detachable
anchors should be latched back
properly.
The seat belts in the second row
center seat and the third row seats
are equipped with detachable
anchors.
To unlatch the detachable anchor,
insert the latch plate into the slot on
the side of the anchor buckle. Store
the detachable anchor and seat belt
latch plates in the retractor housing.
Reverse
this procedure to return the
seat to the upright position. Make
sure the seat is locked securely
befo re driving. Reconnect the seat
belts to the detach able anchors.
Ma ke sure all items in the cargo area
are secured. Loose items can f ly
f orward and cause injury if you have
to brake hard (See
on page ). 324 Detachable Anchor
Carrying Cargo
Seats
144
LATCH PLATE
Using a seat belt with the
detachable anchor unlatched
increases the chance of serious
injury or death in a crash.
Before using the seat belt,
make sure the detachable
anchor is correctly latched.
——y

y
()-y
y

Pull out the small latch plate and the
latch plate f rom each holding slot in
the ceiling, and pull out the seat belt
to extend it.Pull out the outer shoulder belts
f rom the hook. Both of the third-row
hooks should only be used when the
seat belt is detached.Line up the triangle marks on the
small latch plate and anchor buckle
when reattaching the belt and buckle.
Tug on the seat belt to verify that
the detachable anchor is securely
latched. Make sure the seat belt is
not twisted.
Seats
Inst rument s and Cont rols
145
SMALL LATCH PLATELATCH PLATE
SECOND ROW CENTER SEAT
HOOKANCHOR BUCKLE TRIANGLE
MARKS
THIRD ROW SEATS
SMALL LATCH PLATE
——y

y
()-y
y

The outer second row seat cushions
and seat-backs are equipped with
seat heaters. Turning the switch on
the driver side warms the outer seat
behind the driver’s seat only. The
passenger side switch warms the
outer seat behind the f ront
passenger seat.
The ignition switch must be in the
ON (II) position to use them. Push
the front of the switch, HI, to rapidly
heat up the seat. After the seat
reaches a comf ortable temperature,
select LO by pushing the back of the
switch. This will keep the seat warm.
Both f ront seats are equipped with
seat heaters. The passenger seat is
only heated in the seat bottom
because of the side airbag of f system.
U.S. Entertainment Packages and
Canadian Elite Package models
Seat Heaters
146
LOW HI
Front seat Second row seat
HEATERS
Passenger’s
Seat
Driver’s
Seat
——y
y
()-y

y