Acura MDX 2012 Owners Manual

HandsFreeLink™You can receive or make phone calls
from your cell phone through your
vehicle's
Bluetooth
®HandsFreeLink
®
(HFL) system without touching your
cell phone.Trip Computer
When the main menu displays‘‘TRIP
COMPUTER’’, pressing the SEL/
RESET button changes the display to
‘‘AVERAGE FUEL A/RANGE’’to
‘‘AVERAGE FUEL B/RANGE’’and
to‘‘AVERAGE SPEED/ELAPSED
TIME’’.
AVERAGE FUEL A/BThis shows your vehicle's average
fuel economy in mpg (U.S. models)
or liter/100 km (Canadian models)
since you last reset the Trip A or Trip
B.
You can customize the Trip A and
AVERAGE FUEL A reset condition
on the multi-information display (see
page 102).
Multi-Information Display84

RANGEThis shows the estimated distance
you can travel on the fuel remaining
in the fuel tank. This distance is
estimated from the fuel economy you
received over the last several miles
(U.S.) or kilometers (Canada), so it
will vary with changes in speed,
traffic, etc.
AVERAGE SPEEDThis shows the average speed you
are traveling in miles per hour (mph)
for U.S. models or kilometers per
hour (km/h) for Canadian models.
To reset the AVERAGE SPEED you
have traveled, press and hold the
SEL/RESET button until the number
resets.
ELAPSED TIMEThis shows the time passed traveled
since you last reset it. When you turn
the ignition switch to the ON (II)
position, ELAPSED TIME is reset.
If you want to reset the ELAPSED
TIME manually, go to the trip
computer's ELAPSED TIME display,
and press and hold the SEL/RESET
button until the number resets.
You can customize the ELAPSED
TIME reset condition on the multi-
information display (see page 104).
CONTINUED
Multi-Information Display
85
Instruments and Controls

System MessagesIf there is a problem with your
vehicle, for example, the engine oil
level is low or a door is not fully
closed, the multi-information display
will show you the problem. It does
this by interrupting the current
display with one or more messages.The system message(s) triggers the
appropriate indicator(s) on the
instrument panel, including the
system message indicator, to come
on. The system message indicator
does not go off until the problem(s)
is corrected.
You will also hear a beep when the
system message comes on for the
first time.
Most of the messages are displayed
for about 5 seconds, and then the
normal display returns. If there are
several system messages to be
shown, the display switches these
messages every 5 seconds.To cancel the message(s) before 5
seconds have elapsed, press the
INFO (
/
) button on the steering
wheel.
Even if you press the INFO (
/
)
button, some messages stay on or
come on again at regular intervals
until the problem is corrected.
You can see the message(s) again by
pressing the INFO (
/
) button
repeatedly if the system message
indicator remains lit on the
instrument panel.
Here is a list of all messages:
SYSTEM MESSAGE INDICATOR
Multi-Information Display86

See page
12
See page
21
See page
21
See page
36
See page
36See page
164
See page
564
See page
564See page
562
See page
562
See page
563
See Page
443
See page
130
U.S.
Canada
U.S.
CanadaCanada U.S.U.S.
Canada
CONTINUED
Multi-Information Display
87
Instruments and Controls

See page
462
See page
473
See page
499
See page
456
See page
458
See page
456See page
72
See page
144
See page
452
See page
452
See page
443See page
486
See page
522
See page
77
See page
360
See page
75
See page
467
U.S.
Canada
Multi-Information Display88

See page
482
See page
482
See page
547
See page
507
See page
425
CONTINUED
Multi-Information Display
89
Instruments and Controls

Customize SettingsWhen the main menu displays
‘‘Keyless Memory Settings™,’’you
can customize some vehicle control
settings.
To enter the customizing mode,
press the SEL/RESET button.
To change the settings, the ignition
switch must be in the ON (II)
position, and the vehicle must be
stopped with the transmission in
Park.If you turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position, or move the shift lever out
of Park, the display will change to the
normal screen.
You can customize some vehicle
control settings for‘‘DRIVER 1’’and
‘‘DRIVER 2’’separately. If‘‘DRIVER
1’’or‘‘DRIVER 2’’is not displayed,
customizing is not possible.
To have the driver's ID detected,
make sure your remote transmitter is
linked to the system (see Keyless
Memory Settings™on page 148).
If you want the settings as they were
when the vehicle left the factory,
select DEFAULT ALL, as described
on page 93.
If you want to change any vehicle
control settings, select CHG
SETTING, then press the SEL/
RESET button.
Refer to the table on the following
pages about the settings you want to
customize.
Multi-Information Display90

Group Setup Menu Item Description Setting Option Page
ACC SETUP
(P. 96)PRE-RUNNING CAR DETECT
BEEPCauses the system to beep when a vehicle ahead of
you gets too close.ON
ᤳ1
97
OFF
ACC DISPLAY SPEED UNIT Changes the ACC display speed unit. mph
ᤳ2
previous
setting98
km/h
ᤳ3
METER SETUP
(P. 99)LANGUAGE SELECTION Changes the language used in the display. ENGLISH
ᤳ1
100 FRENCH
SPANISH
ADJUST OUTSIDE
TEMP. DISPLAYChanges the outside temperature reading above or
below its current reading.－5°F～ᤣ0°F
ᤳ2～5°F
101
－3°C～ᤣ0°Cᤳ3～3°C
TRIP A & AVG. FUEL
RESET with REFUELCauses trip meter A and the average fuel economy to
reset when you refuel.ON 102
OFF
ᤳ1
ADJUST
ALARM VOLUMEChanges the indicator alarm volumes into three levels. HIGH
103 MID
ᤳ1
LOW
ELAPSED TIME RESET Resets the elapsed time of your current trip. MANUAL ONLY
104 IGN OFF
ᤳ1
TRIP B
TRIP A
AUTO INTERIOR
ILLUMINATIONChanges the interior light sensitivity to your liking. MAX LOW
105 HIGH MIN
MID
ᤳ1
OFF
POSITION SETUP
(P. 107)MEMORY POSITION LINK Changes the driver's seat, the steering wheel, and the
outside mirror positions to a stored setting.ON
ᤳ1
108
OFF
AUTO TILT & TELESCOPE
STEERING WHEELMoves the steering wheel fully in and up when the key
is removed.ON
ᤳ1
109
OFF
ᤳ1: Default setting
ᤳ2: Default setting for U.S. models
ᤳ3: Default setting for Canadian models
CONTINUED
Multi-Information Display
91
Instruments and Controls

Group Setup Menu Item Description Setting Option Page
LIGHTING SETUP
(P. 110)INTERIOR LIGHT
DIMMING TIMEChanges how long (in seconds) the interior lights stay
on after you close the doors and the tailgate.60 sec 15 sec 111
30 sec
ᤳ
HEADLIGHT
AUTO OFF TIMERChanges how long (in seconds) the exterior lights stay
on after you close the driver's door.60 sec
112 30 sec 0 sec
15 sec
ᤳ
AUTO LIGHT
SENSITIVITYChanges the timing of when the headlights come on.
The headlight switch needs to be in the AUTO
position.MAX LOW
113 HIGH MIN
MID
ᤳ
DOOR/WINDOW
SETUP
(P. 115)AUTO DOOR LOCK Changes the setting of when to automatically lock the
doors.SHIFT FROM P
116 WITH VEH SPD
ᤳ
OFF
AUTO DOOR UNLOCK Changes the setting of when to automatically unlock
the driver's/all the doors.SHIFT TO P
ᤳ
DRIVER
DOOR/ALL
DOORS
117 IGN OFF
OFF
KEY AND REMOTE
UNLOCK MODEChanges which doors unlock with the remote
transmitter on a first push.DRIVER DOOR
ᤳ
119
ALL DOORS
KEYLESS LOCK
ACKNOWLEDGMENTThe exterior lights flash each time you press the
LOCK or UNLOCK button. A beeper will also sound
when you press the LOCK button twice.ON
ᤳ
120 OFF
SECURITY RELOCK TIMER Changes how long it takes (in seconds) for the doors
to relock and the security system to set after you
unlock but do not open the door.90 sec
121 60 sec
30 sec
ᤳ
WIPER SETUP
(P. 123)WIPER ACTION Changes the wiper operation between two settings
when the wiper switch is in the INT position.INTERMITTENT 123
WITH VEH SPD
ᤳ
DEFAULT ALL
(P. 93)Set/Cancel all the customized settings as default. SET 93
CANCEL
ᤳ: Default setting
Multi-Information Display92

DEFAULT ALLIf you want to set the default settings,
press the INFO (
/
) button to
select DEFAULT ALL, then press the
SEL/RESET button.
To set the default settings, press the
INFO (
/
) button to select SET
then press the SEL/RESET button.
If you want to cancel DEFAULT ALL,
select CANCEL, then press the SEL/
RESET button. The screen goes back
to the previous display.
When DEFAULT ALL is set, you will
see the above display for several
seconds, then the screen returns to
CUSTOMIZE ENTRY.
If the setting is not successfully
completed,‘‘FAILED’’is shown for
several seconds, and then the screen
goes back to the normal message
mode. Repeat the same procedure to
select DEFAULT ALL.
CONTINUED
Multi-Information Display
93
Instruments and Controls