ECU Acura MDX 2013 User Guide

Installing a Child Seat with a Lap/
Shoulder Belt
When not using the LATCH system,
all child seats must be secured to the
vehicle with the lap part of a lap/
shoulder belt.
In addition, the lap/shoulder belts in
all seating positions except the
driver's have a lockable retractor that
must be activated to secure a child
seat.
If you intend to install a child seat in
the center seating position of second
row seat, make sure the detachable
seat belt is securely latched (see
page 155).
1. With the child seat in the desired
seating position, route the belt
through the child seat according to
the seat maker's instructions, then
insert the latch plate into the
buckle and remove any slack from
the lap portion of the belt.
2. To activate the lockable retractor,
slowly pull the shoulder part of the
belt all the way out until it stops,
then let the belt feed back into the
retractor.
3. After the belt has retracted, tug on
it. If the belt is locked, you will not
be able to pull it out. If you can pull
the belt out, it is not locked, and
you will need to repeat these steps.
CONTINUED
Installing a Child Seat
53
Driver and Passenger Safety
12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu

4. After confirming that the belt is
locked, grab the shoulder part of
the belt near the buckle, and pull
up to remove any slack from the
lap part of the belt. Remember, if
the lap part of the belt is not tight,
the child seat will not be secure.
To remove slack, it may help to put
weight on the child seat, or push
on the back of the seat while
pulling up on the belt.
5. Push and pull the child seat
forward and from side-to-side to
verify that it is secure enough to
stay upright during normal driving
maneuvers. If the child seat is not
secure, unlatch the belt, allow it to
retract fully, then repeat these
steps.
To deactivate the lockable retractor
and remove a child seat, unlatch the
buckle, unroute the seat belt, and let
the belt fully retract.Installing a Child Seat with a
Tether
A child seat with a tether can be
installed in any seating position in
the second or third row.
Since a tether can provide additional
security to the lap/shoulder belt
installation, we recommend using a
tether whenever one is required or
available.
Installing a Child Seat5412/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu

Second Row InstallationEach second row seat has a tether
anchorage point behind the seat-
back.
1. After properly securing the child
seat (see page 53), lift the head
restraint, then route the tether
strap over the seat-back and
through the head restraint legs.
For the center seat, lower the head
restraint, then route the tether strap
over the head restraint and seat-back.
TETHER ANCHORAGE POINT
TETHER STRAP
Outer Seating Position
CONTINUED
Installing a Child Seat
55
Driver and Passenger Safety
12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu

2. Attach the tether strap hook to the
anchor, making sure the tether
strap is not twisted.
3. Tighten the strap according to the
seat maker's instructions.
If the tether strap is too long and
cannot be tightened firmly, find a
route where the strap can be
tightened securely.
Third Row InstallationEach third row seat has a tether
anchorage point on the tailgate sill.
1. Select the anchor point you want to
use. Then open the anchor cover
with a small flat-tip screwdriver.
2. Secure the child seat in the
desired position (see page 53).
3. Remove the head restraint, then
attach the tether strap hook to the
anchor, making sure the strap is
not twisted.
Make sure the removed head
restraint is secured in a safe place.
4. Tighten the strap according to the
seat maker's instructions.
If the tether strap is too long and
cannot be tightened firmly, find a
route where the strap can be
tightened securely.
Installing a Child Seat5612/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu

If you decide that a child can safely
ride up front, be sure to:●Carefully read the owner's manual,
and make sure you understand all
seat belt instructions and all safety
information.●Move the vehicle seat to the rear-
most position.●Have the child sit up straight, back
against the seat, and feet on or
near the floor.●Check that the child's seat belt is
properly and securely positioned.●Supervise the child. Even mature
children sometimes need to be
reminded to fasten the seat belts
or sit properly.Additional Safety Precautions
●Do not let a child wear a seat belt
across the neck.
This could result
in serious neck injuries during a
crash.
●Do not let a child put the shoulder
part of a seat belt behind the back
or under the arm.
This could cause
very serious injuries during a
crash. It also increases the chance
that the child will slide under the
belt in a crash and be injured.
●Two children should never use the
same seat belt.
If they do, they
could be very seriously injured in a
crash.
●Do not put any accessories on a
seat belt.
Devices intended to
improve a child's comfort or
reposition the shoulder part of a
seat belt can make the belt less
effective and increase the chance
of serious injury in a crash.
Protecting Larger Children6012/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu

ᤳ: If equipped
The U.S. instrument panel is shown. Differences for the Canadian models are noted in the text.
MESSAGE INDICATOR (P. 73)
HIGH BEAM INDICATOR (P. 74)
SH-AWD INDICATOR (P. 73)
ANTI-LOCK BRAKE SYSTEM
INDICATOR (P. 70)
FOG LIGHT INDICATOR (P. 74) DOOR/TAILGATE OPEN
INDICATOR (P. 76)
IMMOBILIZER SYSTEM
INDICATOR (P. 74)
CHARGING SYSTEM
INDICATOR (P. 69)
VEHICLE STABILITY ASSIST
(VSA) SYSTEM INDICATOR
(P. 71)
SECURITY SYSTEM INDICATOR (P. 77)
ACTIVE DAMPER SYSTEM INDICATOR
ᤳ(P. 77) PARKING BRAKE AND BRAKE SYSTEM INDICATOR (P. 69)LOW FUEL INDICATOR (P. 77) SEAT BELT REMINDER INDICATOR (P. 68) COLLISION MITIGATION BRAKING
SYSTEM™(CMBS™) INDICATOR
ᤳ(P. 75)
SUPPLEMENTAL RESTRAINT
SYSTEM INDICATOR (P. 36, 70)
CRUISE MAIN INDICATORᤳ(P. 75)/
ADAPTIVE CRUISE CONTROL (ACC) INDICATOR
ᤳ(P. 75) MALFUNCTION INDICATOR
LAMP (P. 69)
VSA OFF INDICATOR
(P. 71)
A/T TEMPERATURE
INDICATOR (P. 72)
BLIND SPOT INFORMATION SYSTEM INDICATOR
ᤳ(P. 76) CRUISE CONTROL
INDICATORᤳ(P. 75) MULTI-INFORMATION DISPLAY (P. 79)
LOW TIRE PRESSURE INDICATOR (P. 72)
LOW OIL PRESSURE
INDICATOR (P. 69)LIGHT ON INDICATOR (P. 74)
SIDE AIRBAG OFF INDICATOR (P. 70)
Instrument Panel
67
Instruments and Controls
12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu

Active Damper System
Indicator
If equippedThis indicator comes on briefly when
you turn the ignition switch to the
ON (II) position. If this indicator
comes on at any other time, there is a
problem in the system. While this
indicator is on, the comfort button
will not work, and the system will
remain in the sport mode. You will
also see a‘‘CHECK ADS SYSTEM’’
message on the multi-information
display. Have the vehicle checked by
your dealer as soon as possible. For
more information, see page 484.Low Fuel Indicator
This indicator comes on as a
reminder that you must refuel soon.
When the indicator comes on, there
is about 2.9 U.S. gal (10.8 L) of fuel
remaining in the tank.
When the needle reaches E, there is
a very small amount of fuel in the
tank.Security System Indicator
This indicator comes on when the
security system is set. See page 341
for more information on the security
system.
LOW FUEL INDICATOR
SECURITY SYSTEM INDICATOR
Instrument Panel Indicators
77
Instruments and Controls
12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu

Group Setup Menu Item Description Setting Option Page
LIGHTING SETUP
(P. 110)INTERIOR LIGHT
DIMMING TIMEChanges how long (in seconds) the interior lights stay
on after you close the doors and the tailgate.60 sec 15 sec 111
30 sec
ᤳ
HEADLIGHT
AUTO OFF TIMERChanges how long (in seconds) the exterior lights stay
on after you close the driver's door.60 sec
112 30 sec 0 sec
15 sec
ᤳ
AUTO LIGHT
SENSITIVITYChanges the timing of when the headlights come on.
The headlight switch needs to be in the AUTO
position.MAX LOW
113 HIGH MIN
MID
ᤳ
DOOR/WINDOW
SETUP
(P. 115)AUTO DOOR LOCK Changes the setting of when to automatically lock the
doors.SHIFT FROM P
116 WITH VEH SPD
ᤳ
OFF
AUTO DOOR UNLOCK Changes the setting of when to automatically unlock
the driver's/all the doors.SHIFT TO P
ᤳ
DRIVER
DOOR/ALL
DOORS
117 IGN OFF
OFF
KEY AND REMOTE
UNLOCK MODEChanges which doors unlock with the remote
transmitter on a first push.DRIVER DOOR
ᤳ
119
ALL DOORS
KEYLESS LOCK
ACKNOWLEDGMENTThe exterior lights flash each time you press the
LOCK or UNLOCK button. A beeper will also sound
when you press the LOCK button twice.ON
ᤳ
120 OFF
SECURITY RELOCK TIMER Changes how long it takes (in seconds) for the doors
to relock and the security system to set after you
unlock but do not open the door.90 sec
121 60 sec
30 sec
ᤳ
WIPER SETUP
(P. 123)WIPER ACTION Changes the wiper operation between two settings
when the wiper switch is in the INT position.INTERMITTENT 123
WITH VEH SPD
ᤳ
DEFAULT ALL
(P. 93)Set/Cancel all the customized settings as default. SET 93
CANCEL
ᤳ: Default settingMulti-Information Display9212/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu

Door/Window Setup
Here are the five custom settings for
the door/window setup:●AUTO DOOR LOCK●AUTO DOOR UNLOCK●KEY AND REMOTE UNLOCK
MODE●KEYLESS LOCK
ACKNOWLEDGMENT●SECURITY RELOCK TIMER
While‘‘DOOR/WINDOW SETUP’’is
shown, press the SEL/RESET button
to enter the customize mode.
Each time you press the INFO
(/
) button, the screen changes as
shown in the illustration. Press the
INFO (
/
) button until you see the
setting you want to customize, then
press the SEL/RESET button to
enter your selection.
SEL/RESET
BUTTON
INFO (▲or▼)
BUTTON
CONTINUED
Multi-Information Display
115
Instruments and Controls
12/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu

Keyless Lock AcknowledgmentWhen you push the LOCK button on
the remote transmitter, some
exterior lights flash, and a beeper
sounds when you push the LOCK
button again within 5 seconds to
verify that the doors and the tailgate
are locked and the security system
has set (see page 341). You can
customize the exterior lights not to
flash and the beeper not to sound.
You can choose this customizable
item from‘‘DOOR/WINDOW
SETUP’’by pressing the INFO (
/
) button repeatedly.
Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO (
/
) button, then enter your
selection by pressing the SEL/
RESET button.
Multi-Information Display12012/07/17 18:10:57 13 ACURA MDX MMC North America Owner's M 50 31STX660 enu