power steering Acura MDX 2014 Advanced Technology Guide

67
\bNSTRUMENT PANEL \bND\bCAT\fRS
Briefly appear with each engine start. Red and amber indicators a\Nre most critical. Blue
and green indicators are used for general information. See your Owner’s \fanual for
more information.
If an indicator remains on, there may be a problem; see your dealer.
Charging system
Low brake fluid, Brake system
Low oil pressure
Vehicle Stability Assist (VSA®)
\falfunction indicator lamp(check engine light)
Tire Pressure \fonitoring System
(TP\fS) (blinks)
Collision \fitigation Braking
SystemT\f(C\fBST\f)*
Super \bandling
AllWheel Drive (S\bAWD)*
SRS(Supplemental Restraint System)
ABS (Antilock Brake System)Blind Spot Information (BSI)*
Brake system (hydraulic)
Electric Power Steering
Keyless Access System
PASSENGER AIRBAG \fFF
(next to display)
VSA \fFF
BSI* off
Immobilizer (blinks):
Use other vehicle key and see dealer
Exterior lights on
Turn signals/hazards onCRUISE
CONTROLCRUISE CONTROL on
CRUISE
MAINCRUISE \fAIN on
\bigh beams on
*if equipped
Action is needed by driver.
Parking brake on:
Release\fessage indicator:
See M\bD
Low tire pressure (stays on):
Add air
Seat belt reminder:
Fasten seat belt(s)Low fuel:
Refill
C\fBS* off
FCW* off
Lane Keeping Assist System* onAdaptive Cruise Control* on
Lane Departure Warning (LDW)*
Forward Collision Warning
(FCW)*
Malfunction \bndicatorsCondition \bndicators
\fn/\fff \bndicators
14 MDX ATG_RP1_Corre\Acted Pages_ATG Facin\Ag \b/5/2013 11\f53 \AAM Page \b

11
10
Default Lock Setting
The doors are preset to lock
when your vehicle reaches
about 10 mph.Default Unlock Setting
All doors are set to unlock when
the driver’s door is opened.
How It WorksAUTO DOOR LOCKSProgram how and when the vehicle doors automatically lock and unlock.
1. Turn on the vehicle. Make sure
the shift lever is in Park (P).
2. Adjust the seat, outside mirrors, and steering wheel to your
preferred positions.
4. Press the memory buttoncorresponding to the remote
(1 or 2) you are using within
5 seconds. You will hear two
beeps.
Notes:
• Once set, stored positions can be recalled by pressing one of thememory buttons (1 or 2) on the door.
• Lumbar position cannot be stored.
DRIVING POSITION MEMORY SYSTEM (DPMS)Store driver’s seat, outside mirror, and steering wheel positions into memory for each
corresponding keyless remote (1 or 2).Programming the DPMS
3. Press SET. You will hear a beep.
1. Press SETTINGS. Use theinterface dial to make and
enter selections.
2. Select Vehicle Settings.
3. Select Auto Door Lock or Auto Door Unlock.
4. Select from the options.
5. Press BACK to exit the menu.
Note: The driver’s and front passenger’s door can be opened by pulling the inner
front door handle, regardless of the setting. Changing the setting to “All Doors”
is useful for unlocking the rear doors and the power tailgate when a front door
handle is pulled.* You can also change these settings using the
multi-information display (see page 8).
Changing Settings
Follow the steps below to change your door settings. Make sure you are using the
key
you want to change settings for (Driver 1 or Driver 2) and the vehicle is on.*
14 MDX ATG_ATG Facing 3/29/2013 12:35 PM Page 10