steering wheel adjustment ACURA NSX 1997 Service Repair Manual

Component Location s
Index
NOTE :
• I f a n intac t airba g assembl y ha s bee n remove d fro m a scrappe d vehicl e o r ha s bee n foun d defectiv e o r damage d durin g
transit , storag e o r service , i t shoul d b e deploye d (se e sectio n 24 ).
• Befor e removin g th e gearbox , remov e th e ignitio n ke y t o loc k th e steerin g shaft .
• Afte r installin g th e gearbox , chec k th e whee l alignmen t an d adjus t i f necessary .
STEERING GEARBO XRemoval/Installation , pag e 17-5 3
Illustrate d Index , pag e 17-5 7
Pinio n Preloa d Inspection , pag e 17-5 8
Rac k Guid e Scre w Adjustment , pag e 17-5 8
STEERIN
G COLUM N
Removal , pag e 17-4 7
Inspection , pag e 17-4 9
Installation , pag e 17-5 0
STEERIN G WHEEL /AIRBAG ASSEMBL YRemoval, pag e 17-4 3
Disassembly , pag e 17-4 4
Installation , pag e 17-4 5
EP
S CONTRO L UNI T
Replacement , pag e 17-62
ProCarManuals.com

4. Connect the horn connector.
Installation

NOTE: Before installing the steering wheel, make sure

the front wheels are straight ahead.

CAUTION:

• Be sure to install the harness wires so that they are

not pinched or interfering with other car parts.

• Do not replace the original steering wheel with any

other design, since it will make it impossible to prop-

erly install the airbag. (Use only genuine Honda

replacement parts.)

• After reassembly, confirm that the wheels are still

straight ahead and that steering wheel spoke angle

is correct. If minor spoke angle adjustment is neces-

sary, adjust the tie-rods only. Do not remove and

reposition the steering wheel.

Confirm that the driver's airbag assembly

is securely attached to the steering wheel; otherwise,

severe personal injury could result during later airbag

deployment.

1. Before installing the steering wheel, center the

cable reel.

Do this by first rotating the cable reel clockwise

until it stops.

Then rotate it counterclockwise (approximately two

turns) until:

— The yellow gear tooth lines up with the mark on

the cover.

— The arrow on the cable reel label points straight

up.
2. Install the steering wheel.

NOTE: Be sure the steering wheel shaft engages

the cable reel.

3. Attach the cruise control set/resume switches 4P

connector to the steering wheel clips.ProCarManuals.com

Supplemental Restraint System (SRS)

Cable Reel Installation

CAUTION:

Before installing the steering wheel, the front wheels

should be aligned straight ahead.

Be sure to install the harness wires so that they are

not pinched or interfering with other car parts.

After reassembly, confirm that the wheels are still

turned straight ahead and that steering wheel spoke

angle is correct. If minor spoke angle adjustment is

necessary, do so only by adjusting the tie-rods, not

by removing and repositioning the steering wheel.

1. Align the cancel sleeve grooves with the cable reel

projections.

CANCEL SLEEVE

CABLE REEL

GROOVES

PROJECTIONS

2. Carefully install the cable reel and the cancel sleeve

on the steering column shaft.

CABLE REEL

CANCEL SLEEVE

STEERING COLUMN

SHAFT
3. Install the column covers.

4. Center the cable reel.

Do this by first rotating the cable reel clockwise un-

til it stops.

Then rotate it counterclockwise (approximately

two turns) until:

The yellow gear tooth lines up with the align-

ment mark on the cover.

The arrow mark on the cable reel label points

straight up.

ARROW MARK

CABLE REEL LABEL

ALIGNMENT MARK

YELLOW GEAR TOOTH

5. Install the steering wheel, and attach the cable reel

3-P connector to the steering wheel clips.

6. Connect the horn connector and cruise control

connector.

CRUISE CONTROL

SET/RESUME

SWITCH CONNECTOR

HORN

CONNECTOR

CABLE REEL

3P CONNECTORProCarManuals.com