ignition Acura RL 2002 3.5 Service Manual

µµ
µ
µ´ ´ µ
You can use any of three methods to
f ind radio stations on the selected
band: TUNE, SEEK, or the Preset
buttons.
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the TUNE knob to the right to
tune to a higher f requency, or to the
lef t to tune to a lower f requency.
Turn the knob right or lef t until the
display reaches the desired
f requency. You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band.
The SEEK f unction
searches the band for a station with
a strong signal. To activate it, push ei-
ther side of the SEEK/SKIP buttons
( or ). Push the button to
scan up f rom the current f requency,
andthe buttontoscandown.It
stops when it finds a station with a
strong signal.
The band and f requency that the ra-
dio was last tuned to is displayed. To
change bands, press the AM/FM but-
ton. On the FM band, ST will be dis-
played if the station is broadcasting
in stereo. ST will flash if you are driv-
inginanareawheretheradiosignal
is weak. Stereo reproduction on AM
is not available. The ignition switch must be in
ACCESSORY (I) or ON (II) to
operate the audio system. Turn the
system on by pushing the PWR/
VOL knob or the AM/FM button.
Adjust the volume by turning the
knob.
CONT INUED
TUNE
Preset
SEEK
Operating the Radio
Audio System
Comf ort and Convenience Feat ures
3.5 RL wit hout Navigat ion Syst em
129
01/09/28 19:45:42 31SZ3660_132

ÛWhen the system reaches the end of
the tape, it will automatically reverse
direction and play the other side. If
you want to remove the cassette
f rom the drive, press the EJECT
button.
If you turn the system of f while a
tape is playing, either with the PWR/
VOL knob or by turning of f the
ignition, the cassette will remain in
the drive. When you turn the system
back on, the tape will begin playing
where it lef t of f .
To switch to the radio or CD
changer while listening to a tape,
press the AM/FM or CD/TAPE but-
ton. To change back to the cassette
player, press the CD/TAPE button.
Make sure the tape opening on the
cassette is facing to the right, then
insert the cassette most of the way
into the slot. The system will pull it
in the rest of the way, and begin to
play. The ignition switch must be in
ACCESSORY (I) or ON (II).
The tape direction indicator will light
to show you which side of the
cassette is playing. The indicates
thesideyouinsertedfacingupward
is now playing. If you want to play
the other side, press the PROG/
PLAY button.
Dolby noise reduction turns on when
you insert a cassette. If the tape was
not recorded with Dolby noise reduc-
tion, turn it of f by pressing the
button.
You can use the instrument panel
brightness control dial to adjust the il-
lumination of the audio system (see
page ). The audio system
illuminates when the parking lights
are on, even if the radio is turned of f .
For inf ormation, See page .
66
141
Audio System
Comf ort and Convenience Feat ures
Operating the Cassette Player
A udio System L ighting
Radio Frequencies and Reception
133
01/09/28 19:46:23 31SZ3660_136

µ´
´
µ µ
µ
You can use the SEEK/SKIP buttons
to select tracks within a disc. If you
push and release either side of the
SEEK/SKIP buttons ( or ), the
system will move to the beginning of
a track. Push the button to move
to the beginning of the next track,
and push the button to move to
the beginning of the current track.
If you push and hold the SEEK/
SKIP button, you will hear a beep
and the system will continue to move
across tracks. Release the button
when you think it has reached the de-
sired place on the disc. When you activate the
Repeat feature by pressing the
REPEAT button, the system continu-
ously replays the current track. You
will see RPT in the display as a
reminder. Press the REPEAT button
again to turn it off.
This feature,
when activated, plays the tracks on a
CD in random order, rather than in
the order they are recorded on the
CD. To activate Random Play, press
the A. SELECT button. You will see
A. SELECT in the display. The sys-
tem will then select and play tracks
randomly on the current disc. When
all tracks on that disc have been
played, the next disc is loaded and
played randomly. This continues un-
til you deactivate Random Play by
pressing A. SELECT again. To take the system out of CD mode,
press the AM/FM button or insert a
cassette in the player. If a tape is
already in the cassette player, press
the CD/TAPE button. When you
return to CD mode, play will contin-
ue at the same point that it left off.
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or the ignition switch, play will
continue at the same point when you
turn it back on.
For inf ormation on how to handle
and protect compact discs, see page
.
153
Audio System
Comf ort and Convenience Feat ures
REPEAT
RANDOM PLAY
Protecting Compact Discs
138
01/09/28 19:47:09 31SZ3660_141

µ
µ
µ µ
´ ´ µ
You can use any of three methods to
f ind radio stations on the selected
band: TUNE, SEEK, or the Preset
buttons.
You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band.
The band and f requency that the ra-
dio was last tuned to is displayed. To
change bands, press the AM/FM but-
ton. On the FM band, ST will be dis-
played if the station is broadcasting
in stereo. ST will flash if you are driv-
inginanareawheretheradiosignal
is weak. Stereo reproduction on AM
is not available. The ignition switch must be in
ACCESSORY (I) or ON (II) to
operate the audio system. Turn the
system on by pushing the PWR/
VOL knob or the AM/FM button.
Adjust the volume by turning the
knob. Use the TUNE bar to tune
the radio to a desired f requency.
Push and release the appropriate
side of the bar quickly. The
f requency numbers will change in
small increments.
The SEEK f unction
searches the band for a station with
a strong signal. To activate it, push
either side of the SEEK bar ( or ) until you hear a beep. Push the
bar on the side to scan up f rom
the current f requency, and on the
side to scan down. It stops when it
finds a station with a strong signal.
CONT INUED
Preset
Operating the Radio
TUNE
SEEK
Audio System
Comf ort and Convenience Feat ures
3.5 RL wit h Navigat ion Syst em
139
01/09/28 19:47:20 31SZ3660_142

Ûµ
Make sure the tape opening on the
cassette is facing to the right, then
insert the cassette most of the way
into the slot. The system will pull it
in the rest of the way, and begin to
play. The ignition switch must be in
ACCESSORY (I) or ON (II).
The tape direction indicator will light
to show you which side of the
cassette is playing. The indicates
thesideyouinsertedfacingupward
is now playing. If you want to play
the other side, press the PROG/
PLAY button. When the system reaches the end of
the tape, it will automatically reverse
direction and play the other side. If
you want to remove the cassette
f rom the drive, press the EJECT
button.
With a cassette playing, you can use
the FF, REW, TMS, or REPEAT
f unction to f ind a desired program.
If you turn the system of f while a
tape is playing, either with the PWR/
VOL knob or by turning of f the
ignition, the cassette will remain in
the drive. When you turn the system
back on, the tape will begin playing
where it lef t of f .
To switch to the radio or CD
changer while listening to a tape,
press the AM/FM or CD/TAPE but-
ton. To change back to the cassette
player, press the CD/TAPE button. Fast Forward and
Rewind move the tape rapidly. To
rewind the tape, push the REW
button. The indicator in this button
will light. To f ast f orward the tape,
push the FF button. The indicator in
this button will light. Press the
PROG/PLAY button to take the
system out of rewind or f ast f orward.
When the system reaches the end of
the tape, it reverses direction and
begins to play if in f ast f orward, or it
begins to play if in rewind.
Dolby B noise reduction turns on
when you insert a cassette. The
indicator in the button will light.
If thetapewasnotrecordedwith
Dolby B noise reduction, turn it of f
by pressing the button.
CONT INUED
Operating the Cassette Player Tape Search Functions
FF/REW
Audio System
Comf ort and Convenience Feat ures145
01/09/28 19:48:22 31SZ3660_148

µ
µ
µ´ ´
µ µ
µ´
This feature,
when activated, plays the tracks on a
CD in random order, rather than in
the order they are recorded on the
CD. To activate Random Play, press
the A. SELECT button. You will see
A. SELECT in the display. The sys-
tem will then select and play tracks
randomly on the current disc. When
all tracks on that disc have been
played, the next disc is loaded and played randomly. This continues un-
til you deactivate Random Play by
pressing A. SELECT again.
To take the system out of CD mode,
press the AM/FM button or insert a
cassette in the player. If a tape is
already in the cassette player, press
the CD/TAPE button. When you
return to CD mode, play will contin-
ue at the same point that it left off.
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or the ignition switch, play will
continue at the same point when you
turn it back on.
To select a dif f erent disc, press the
appropriate preset button (1 6). If
you select an empty slot in the
magazine, the changer will, af ter
f inding that slot empty, try to load
the CD in the next slot. This
continues until it f inds a CD to load
and play.
You can use the SEEK bar to select
tracks within a disc. If you push and
release either side of the SEEK bar
( or ), the system will move to
the beginning of a track. Push the
button to move to the beginning of
the next track, and push the but-
ton to move to the beginning of the
current track.
When you activate the
Repeat feature by pressing the
REPEAT button, the system
continuously replays the current
track. You will see REPEAT in the
display as a reminder. Press the
REPEAT button again to turn it off.
For inf ormation on how to handle
and protect compact discs, see page.
If you push and hold the SEEK bar
( or ), you will hear a beep and
the system will continue to move
across tracks. Release the button
when you think it has reached the
desired place on the disc.
153
RANDOM PLAY REPEAT
Protecting Compact Discs
Audio System
Comf ort and Convenience Feat ures150
01/09/28 19:49:08 31SZ3660_153

You make up and provide your
Personal Identification Number
(PIN) when you establish your
account with OnStar. You should
write down your PIN and keep it
with you at all times.
You can change your PIN at any time.
Contact the OnStar advisor by
pressing the OnStar button, or by
calling (888) 4-ONSTAR.
If you f orget your PIN, contact the
OnStar advisor. For security reasons,
your PIN will be mailed to you.OnStar uses the Global Positioning
System (GPS) to locate your vehicle
f or f unctions such as route guidance
and roadside assistance. GPS is
af f ected by structures that can
obstruct the signal, such as tunnels,
parking structures, and tall buildings.
It may not be possible f or OnStar to
pinpoint your location if you are in or
near such structures.
OnStar uses cellular technology to
communicate with your vehicle.
Cellular coverage varies by location,
which may af f ect the ability to
establish a connection, or the quality
of the connection.When you turn of f your vehicle’s
ignition, the OnStar system goes into
low-power mode. Af ter 48 hours, it
switches to sleep mode to conserve
your vehicle’s battery power.
Features such as remote door
unlocking and misplaced vehicle
assistance will not work af ter your
vehicle has been parked f or more
that 48 hours.
Comf ort and Convenience Feat ures
OnStar System
Personal Identif ication Number System Limitations
175
01/09/28 19:54:19 31SZ3660_178

Make sure all windows, mirrors,
and outside lights are clean and
unobstructed. Remove f rost, snow,
or ice.
Check that the hood and trunk are
f ully closed.Check the adjustment of the
inside and outside mirrors (see
page ).
Check the adjustment of the
steering wheel (see page ).
Make sure the doors are securely
closed and locked.
Fasten your seat belt. Check that
your passengers have f astened
their seat belts (see page ).Turn the ignition switch ON (II).
Check the indicator lights in the
instrument panel.
Start the engine (see page ).
Check the gauges and indicator
lights in the instrument panel (see
page ).
Visually check the tires. If a tire
looks low, use a gauge to check its
pressure.
Check that any items you may be
carrying with you inside are stored
properly or f astened down
securely.
Youshoulddothefollowingchecks
and adjustments every day bef ore
you drive your car.
Check the adjustment of the seat
(see page ).
1.
2.
3.
4. 5.
6.
7.
8.
9.
10.
11. 12. 53
15
86
91 191
71
Preparing to Drive
Driving190
01/09/28 19:56:40 31SZ3660_193

Push the accelerator pedal half-
way to the f loor and hold it there
while starting the engine. Do not
hold the ignition key in START
(III) f or more than 15 seconds.
When the engine starts, release
the accelerator pedal gradually as
the engine speeds up and smooths
out.
If the engine fails to start in step 2,
push the accelerator pedal to the
f loor and hold it there while you
try to start the engine for no more
than 15 seconds. If the engine
does not start, return to step 2.
If the engine still does not start,
press the accelerator pedal all the
way down and hold it there while
starting in order to clear f looding.
As bef ore, keep the ignition key in
the START (III) position f or no
more than 15 seconds. Return to
step 5 if the engine does not start.
If it starts, lif t your f oot of f the
accelerator pedal so the engine
does not race.
An engine is harder to start in cold
weather. The thinner air f ound at
high altitude above 8,000 f eet (2,400
meters) adds to the problem.
Use the f ollowing procedure: Turn of f all electrical accessories
to reduce the drain on the battery.
Apply the parking brake.
In cold weather, turn of f all
electrical accessories to reduce
the drain on the battery.
Make sure the shif t lever is in
Park. Press on the brake pedal.
Without touching the accelerator
pedal, turn the ignition key to the
START (III) position. If the engine
does not start right away, do not
hold the key in START (III) f or
more than 15 seconds at a time.
Pause f or at least 10 seconds
bef ore trying again.
If the engine does not start within
15 seconds, or starts but stalls
right away, repeat step 4 with the
accelerator pedal pressed half-way
down. If the engine starts, release
pressure on the accelerator pedal
so the engine does not race.
1.
2.
3.
4.
5.
6.
1.2.
3.
Starting in Cold Weather at High
A ltitude (A bove 8,000 f eet/
2,400 meters)
Driving
Starting the Engine
191
01/09/28 19:56:53 31SZ3660_194

Your Acura’s transmission has f our
f orward speeds, and is electronically
controlled f or smoother shif ting. It
also has a ‘‘lock-up’’ torque converter
forbetterfueleconomy.Youmay
f eel what seems like another shif t
when the converter locks.
This indicator between the f uel
gauge and temperature gauge shows
which position the shif t lever is in.The shift lever has seven positions.
It must be in Park or Neutral to start
the engine. When you are stopped in
D,D,2,1,NorR,pressfirmlyon
the brake pedal, and keep your f oot
of f the accelerator pedal.
The ‘‘D ’’ indicator comes on f or a
f ew seconds when you turn the
ignition switch ON (II). If it f lashes
while driving (in any shif t position),
it indicates a possible problem in the
transmission. Avoid rapid acceler-
ation and have the transmission
checkedbyanauthorizedAcura
dealer as soon as possible.
43
4
Automatic Transmission
Driving
Shif t L ever Position Indicator Shif t L ever Positions
192
S SH
H I
IFFT T L
LEE V
V E
ER
R
01/09/28 19:57:02 31SZ3660_195