ignition Acura RL 2002 3.5 Workshop Manual

µµ
µ
CONT INUED
Whenever you move the shif t lever,
slide it along the guide on the
console. This position mechani-
cally locks the transmission. Use
Park whenever you are turning of f or
starting the engine. To shif t out of
Park, you must press on the brake
pedal and have your f oot of f the
accelerator pedal. Move the shif t
lever to the right to shif t out of the Park position.
If you have done all of the above and
still cannot move the lever out of
Park, see Shif t Lock Release on page
.
To avoid transmission damage, come
to a complete stop bef ore shif ting
into Park. The shif t lever must be in
Park bef ore you can remove the key
from the ignition switch. To shif t to Reverse
f rom Park, see the explanation under
Park. To shif t to Reverse f rom
Neutral, come to a complete stop and
then shift. Push down on the shift
lever bef ore shif ting into Reverse
from Neutral.
Use Neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to Park posi-
tion if you need to leave the car for
any reason. Press on the brake pedal
when you are moving the shif t lever
f rom Neutral to another gear.
195
To shift from:
PtoR
NtoR 2to1
1to2
2toD
DtoD DtoN
DtoD Dto2
NtoD RtoNRtoP Do this:
Press the brake pedal.
Push down on the shif t lever.
Move the lever.
3
34 4
43 3 4
Driving
Automatic Transmission
Park (P) Reverse (R)
Neutral (N)
193
01/09/28 19:57:13 31SZ3660_196

This allows you to move the shif t
lever out of Park if the normal
method of pushing on the brake
pedal does not work.Set the Parking brake.
Remove the key from the ignition
switch.
Put a cloth on the edge of the Shif t
Lock Release slot cover next to
the shift lever.
Use a small flat-tipped screwdriver
or small metal plate (neither are
included in the tool kit) to remove
the cover. Caref ully pry on the
edge of the cover. Push down on the key and move
the shift lever out of Park to
Neutral. Insert the key in the Shift Lock
Release slot.
If you need to use the Shif t Lock
Release, it means your car is
developing a problem. Have the car
checked by your Acura dealer.Remove the key from the Shift
Lock Release slot, then reinstall
thecover.Makesurethenotchon
the cover is on the right side.
Depress the brake pedal and
restart the engine.
1.
2.
3.
4.
5.6.
Driving
Automatic Transmission
Shif t L ock Release
195
S SH
H I
IFFT T L
LOOC CKK R
REEL
LEE A
A S
SEE S
SLLOOT T
01/09/28 19:57:32 31SZ3660_198

The VSA system indicator (see page) comes on and stays on when
there is a problem with the VSA
system. If the VSA indicator comes on while
driving, pull to the side of the road
when it is saf e and turn of f the
engine. Reset the system by
restarting the engine, and watch the
VSA system indicator. If the
indicator remains on, or comes back
on while driving, have the VSA
system inspected by your Acura
dealer.
When VSA is off, the VSA Activation
Indicator light comes on as a
reminder. Pressing the switch again
turns the system back on.
If the indicator does not come on
when the ignition switch is turned
ON(II),theremaybeaproblem
with the VSA system. Have your
dealer inspect your car as soon as
possible.
Without VSA, your car will have
normal braking and cornering ability,
but it will not have VSA traction and
stability enhancement.
This switch is under the lef t vent.
Press it to turn the Vehicle Stability
Assist system on and of f .
56
Driving
Vehicle Stability Assist (VSA) System
VSA Syst em Indicat orVSA Of f Switch
202
V V
S
SAA S
SYYSSTTE
EM
M I
INND DI
ICCA A T
TO
OR R
01/09/28 19:58:38 31SZ3660_205

Loosen the drain plug on the
bottom of the radiator. The
coolant will come out through the
hole in the splash cover.
Turn the ignition ON (II). Turn
the heater temperature control
dial to maximum heat (climate
control to 90°F/32°C). Turn of f
the ignition. Open the hood. Make
sure the engine and radiator are
cool to the touch.
Remove the radiator cap.
Thecoolingsystemshouldbe
completely drained and ref illed with
new coolant according to the time
and distance recommendations in
the maintenance schedule. Only use
Honda All Season Antif reeze/
Coolant Type 2. Use of any non-
Honda coolant or plain water can
result in corrosion and deposits in
the cooling system.
Draining the coolant requires access
to the underside of the car. Unless
you have the tools and knowledge,
you should have this maintenance
done by a skilled mechanic.
1.
2.3.
CONT INUED
Replacing Engine Coolant
Cooling Syst em
Maint enance233
D D
R
RAA I
INN P
PL
LUUG G
01/09/28 20:03:32 31SZ3660_236

Clean up any dirt and oil that have
collected around the ignition coils. Remove the two bolts and the f our
nuts with a wrench and remove
the tower bar. Then remove the
A/C tube f rom the three clips.
Remove the two bolts and the
three nuts with a 7/16 inch (10
mm) wrench, then remove the
engine cover.
The spark plugs in your car are a
special platinum-tipped design f or
longer lif e. The spark plugs should
be replaced according to the time
and distance recommendations in
the maintenance schedule.
1. 2.3.
CONT INUED
Replacement
Spark Plugs
Maint enance243
B BOOL LTT S
S N
NU
UTTS
S
B
BO
OL LTT S
S
N
NU UTTS
S
N
NU
UTTS
S
01/09/28 20:05:17 31SZ3660_246

Put the new spark plug into the
socket, then screw it into the hole.
Screw it in by hand so you do not
crossthread it.
Use a wrench to remove the two
bolts holding the ignition coil.
Remove the ignition coil by pulling
it straight out.
Remove the spark plug with
a f ive-eighths inch (16 mm) spark
plug socket.
Disconnect the wire connector
f rom the ignition coil by pushing
on the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.
4. 5.
6.7.
Spark Plugs
Maint enance244
I IG
GN NIITT I
IOON N C
COOI ILL
I
IG
GN NIITT I
IOON N C
COOI ILL
L
LO OC CKK T
TA
A B
BC
CO
ON NNNEEC
CT TO
OR R B
BO
OL LTT S
S
01/09/28 20:05:25 31SZ3660_247

Install the ignition coil. Reinstall
the two hold-down bolts.
Repeat this procedure f or the
other f ive spark plugs.
Torque the spark plug. (If you do
not have a torque wrench, tighten
the spark plug two-thirds of a turn
af ter it contacts the cylinder head.)
Tightening torque: Put the A/C tube back in place.
Install the tower bar and tighten
the two bolts and the f our nuts.
Tightening torque:
Push the wire connector onto the
ignition coil. Make sure it locks in
place. Install the engine cover. First
tighten the two bolts on the front
of the engine cover, then tighten
the three nuts on the engine cover.
Tightening torque:
8. 9.
10.
11. 12.
13.
14.
CONT INUED
Spark Plugs
Maint enance245
13 lbf·ft (18 N·m , 1.8 kgf·m) 16 lbf·ft (22 N·m , 2.2 kgf·m)
7 lbf·ft (9.8 N·m , 1.0 kgf·m)
Tighten the spark plugs caref ully. A
spark plug that is too loose can
overheat and damage the engine.
Overtightening can cause damage to
the threads in the cylinder head.
01/09/28 20:05:37 31SZ3660_248

µ
Check the condition of the wiper
blades at least every six months.
Look f or signs of cracking in the
rubber, or areas that are getting
hard. Replace the blades if you f ind
these signs, or if they leave streaks
and unwiped areas when used.
Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold it in while you
push the blade assembly toward
thebaseof thearm.
To replace the blade:
Turn the ignition ON (II), switch
the wipers to INT or (low
position), then turn the ignition
OFF when the wiper arm is
approximately midway in its travel. 2.
1.
CONT INUED
Wiper Blades
Maint enance249
W WI IPP E
ER
R A
AR
RMM S
S
L
LOOC CKK
T
T A
A B
B
01/09/28 20:06:10 31SZ3660_252

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.Examine the new wiper blades. If
they have no plastic or metal rein-
f orcement along the back edge,
remove the metal reinf orcement
strips f rom the old wiper blade and
install them in the slots along the
edge of the new blade.Slide the new wiper blade into the
holder until the tabs lock.
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Turn the ignition switch ON (II)
and return the windshield wipers
to their park position.
3. 4. 5.
6.
7.
Wiper Blades
Maint enance250
B BL
LAA D
DE
E B
BLLAA D
DE
E
R
RE EI
INNF FOOR RCCEEM
M E
EN
NT T
01/09/28 20:06:18 31SZ3660_253

If you have a f lat tire while driving,
stop in a saf e place to change it.
Stopping in traf f ic or on the shoulder
of a busy road is dangerous. Drive
slowly along the shoulder until you
gettoanexitoranareatostopthat
is far away from the traffic lanes.Open the trunk. Raise the trunk
f loor by lif ting up on the back edge.
To keep the trunk f loor out of the
way, attach the hook into the slot
in the trunk lid.
Take the tool kit out of the trunk.
Unscrew the wing bolt and take
the spare tire out of its well.
Turn on the hazard warning lights
and turn the ignition switch to
LOCK (0). Have all the
passengers get out of the car while
you change the tire. Park the car on f irm, level, and
non-slippery ground away f rom
traf f ic. Put the transmission in
Park. Apply the parking brake. 5. 4. 3.
2. 1.
CONT INUED
Changing a Flat T ire
T aking Care of t he Unexpect ed283
T T R
RU UN NKK F
FLLOOO ORR
S
SP PA
A R
REE T
TI
IRRE E
J
JA A C
CKK T
TO
OO OLL K
KIITT
H
H
O
OO OKK
The car can easily roll off the
jack, seriously injuring anyone
underneath.
Follow the directions for
changing a tire exactly, and
never get under the car when it
is supported only by the jack.
01/09/28 20:11:37 31SZ3660_286