buttons Acura RL 2004 3.5 Owner's Manual

µYour dealer will reset this indicator
af ter completing the scheduled
maintenance. If this maintenance is
done by someone other than your
Acura dealer, reset the indicator as
f ollows.
Turn of f the engine.
For the f irst 6,000 miles (9,600 km)
af ter the Maintenance Required
Indicator is reset, it will come on f or
two seconds when you turn the
ignition switch to ON (II). Between 6,000 miles (9,600 km) and
7,500 miles (12,000 km) this
indicator will light f or two seconds
when you first turn the ignition
switch to ON (II), and then flash for
ten seconds.
Press and hold the select and reset
buttons next to the instrument pan-
el,thenturntheignitionswitch
ON (II).
Hold the buttons for
approximately ten seconds until
the indicator resets.
This indicator reminds you that it is
time to take your car in for
scheduled maintenance.
If you exceed 7,500 miles (12,000
km) without having the scheduled
maintenance perf ormed, this
indicator will remain on as a constant
reminder.
Ref er to the Maintenance Schedules
f or Normal and Severe Driving
Conditions on pages
. 1.
2.
3.
244 248
Maintenance Required Indicator
Gauges
Inst rument s and Cont rols66
MAINTENANCE REQUIRED INDICATOR
SELECT
BUTTON
RESET
BUTTON

If you unlock the doors with the
remote transmitter, but do not open
any of the doors within 30 seconds,
the doors automatically relock and
the security system sets.
You cannot lock any of the doors
with the remote transmitter if any
door is not f ully closed or the key is
in the ignition switch. You cannot
unlock any of the doors with the key
in the ignition switch.
To open the trunk, push the Trunk
Release button f or approximately
one second.
You can open the trunk with the
remote transmitter regardless of the
position of the main switch in the
glove box. The trunk will not open if
the key is in the ignition switch.You can program the keyless entry
system so it does not beep when you
lock and unlock the doors. This
procedure only turns of f the beep;
the exterior lights will still f lash.
Panic mode allows you to remotely
activate your car’s security system to
attract attention. When activated, the
horn will sound, and the exterior
lights will f lash, f or about 30 seconds.
To activate panic mode, press and
hold the PANIC button for about two
seconds.
To cancel Panic mode bef ore 30
seconds, press any button on the
remote transmitter. You can also
turn the ignition switch to ON (II).
Panic mode will not activate if the
ignition switch is in the ON (II)
position.
To turn this feature off, stand near
the vehicle with the remote
transmitter. Press and hold the
Trunk Release button, then press the
Lock button within one second. You
should see the LED on the remote
transmitter come on f or one second.
Release the buttons after the LED
goes out.
To turn this feature on, repeat the
above procedure. You should see the
LED blink twice.
Af ter you program the remote
transmitter, make sure the trunk lid
is closed.
CONT INUED
T urning t he Beep Of f and On
Panic Mode
Keys and Locks
Inst rument s and Cont rols85

Press and release the MEMO
buttononthecontrolpanel.You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator light in the
memory button will come on. The
current positions of the driver’s
seat, steering wheel, and outside
mirrors are now stored.
Your Acura has a memory f eature
f or the steering wheel, driver’s seat,
and outside mirror positions.
Turn the ignition switch ON (II).
You cannot add a new driving
position in the memory unless the
ignition switch is ON (II). You can
recall a memorized position with
the ignition switch in any position.
Two seat, steering wheel, and
outside mirror positions f or dif f erent
drivers or driving conditions can be
stored in separate memories. You
select a memorized position by
pushing the appropriate button.
Adjust the seat to a comfortable
position (see page ). Adjust
the steering wheel to a
comf ortable position (see page). Adjust the outside mirrors
f or best visibility (see page ).
Store a driving position as explained
in this section only when the vehicle
is parked.
3.
1.
2.
76 96
91
St oring a Driving Posit ion in Memory
Driving Posit ion Memory Syst em
Inst rument s and Cont rols98
MEMO BUTTON

Doing any of the f ollowing af ter
pressing the MEMO button will
cancel the storing procedure.Not pressing a memory button
within 5 seconds.
Readjusting the seat or steering
position.
You can select memorized positions
as f ollows.Make sure the parking brake is set
and the shif t lever is in Park.
Insert the key in the ignition
switch. If you do not insert the key
in the ignition switch, the steering
wheel will not adjust to the
memorized position until you do. Press the desired memory button
(1 or 2) until you hear a beep, then
release the button.
The system will move the seat,
steering wheel and outside mirrors
to the memorized positions. The
indicator light in the selected
memory button will f lash during
movement. When the adjustments
are complete, you will hear two
beeps and the indicator light will
remain on.
Readjusting the outside mirror
position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button.
All stored driving positions will be
lost if your car’s battery goes dead or
is disconnected. 3.
1.
2.
CONT INUED
Select ing a Memorized Posit ion
Inst rument s and Cont rols
Driving Posit ion Memory Syst em
99
MEMORY BUTTONS

1:06 would RESET to 1:00.
1:52 would RESET to 2:00.
For example: You can use the RESET button to
quickly set the time to the nearest
hour. If the displayed time is bef ore
the half hour, pressing the RESET
buttonsetstheclockbacktothe
previous hour. If the displayed time
is af ter the half hour, pressing the
RESET button sets the clock f or-
ward to the beginning of the next
hour. Press and hold the MIN. button
until the numbers advance to the
desired time. Press and hold the HOUR button
until the hour advances to the
desired hour.
The digital clock displays the time
with the ignition switch ON (II). To
see the time with the ignition off,
press and hold the wide button to the
right of the clock. To set the clock:
Turn the ignition switch ON (II) to
display the time.
Swing down the f ront cover of the
wide button to the right of the
clock display. You will see HOUR,
MIN., and RESET buttons.
2. 3.
4.
1.
Cars without Navigation System
Digital Clock
Inst rument s and Cont rols108
HOUR MIN. RESET

You can manually select the f an
speedbyturningthefancontroldial.
When you turn the dial clockwise,
the fan is taken out of automatic
mode and starts to run at its lowest
speed. Turning the dial f ully
clockwise increases the f an’s speed,
which increases air flow.Use the MODE button to select the
vents the air flows from. Some air
will f low f rom the side vents and the
dashboard corner vents in all modes.
Each time you press the MODE
button, the display shows the mode
selected. Press the button four times
to see all the modes.
These two buttons control the
source of the air going into the sys-
tem. In Fresh Air mode ( ),
air is brought in f rom outside the ve-
hicle. In Recirculation mode
( ), air f rom the vehicle’s inte-
rior is sent through the system again.
You can, f or example, manually put
the system in recirculation mode
when driving through an area of
smoke or f umes. When you press
the or button, the
light in that button comes on.
Climat e Cont rol Syst em
Comf ort and Convenience Feat ures
Mode Button
Recirculat ed and Fresh A ir
Fan Cont rol Dial
124
MODE BUTTON FAN CONTROL DIAL
RECIRCULATED AIR FRESH AIR

When you turn the A/C of f , the
system cannot regulate the inside
temperature if you set it below the
outside temperature. With the A/C
on, use the temperature buttons to
adjust the temperature of the air
flow to a comfortable setting.
With the A/C in economy mode, you
will see A/C ECON in the display.
Usethismodetogetbetterfuel
economy.
In this mode, you may f eel a slight re-
duction in cooling ef f iciency. If you
want more cooling, select A/C ON or
FULL AUTO.This button controls the source of
the air going into the system. When
the indicator above this button is lit,
air f rom the vehicle’s interior is sent
through the system again (Recircula-
tion mode). When the indicator is off,
air is brought in f rom outside the
vehicle (Fresh Air mode).
You can, f or example, manually put
the system in recirculation mode
when driving through an area of
smoke or f umes.
You can manually select the f an
speed with the f an speed icon.
Touching the icon repeatedly makes
the fan run faster. The fan speed is
shownbybarsinthedisplay.If the
f an is at its highest speed, touching
the icon again takes it to its lowest
speed.
To remove f og f rom the inside of the
windows (on very cold days), you
select , the A/C turns on
automatically and the system selects
Fresh Air mode.
CONT INUED
Climat e Cont rol Syst em
Comf ort and Convenience Feat ures
Recirculat ion But t on Fan Speed Icon
129

Î
Î
Your Acura’s audio system provides
clear reception on both AM and FM
bands, while the preset buttons allow
you to easily select your f avorite
stations.
The cassette system f eatures Dolby
noise reduction, automatic sensing of
chromium-dioxide (CrO ) tape, and
auto-reverse f or continuous play.
The in-dash CD changer holds up to
six discs. You operate the CD
changer with the same controls used
f or the radio. See page f or CD
changer operation.The anti-thef t f eature will disable the
system if it is disconnected f rom the
vehicle’s battery. To get the system
working again, you must enter a
code number (see page ).
143
180
2
Dolby noise reduction manuf actured under
license from Dolby Laboratories Licensing Corpo-
ration. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
A M/FM/Cassette/CD Changer
Audio System3.5 RL wit hout Navigat ion Syst em
Audio System
Comf ort and Convenience Feat ures134

µ
µ ÓÓ µ
µ´
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the TUNE knob to the right to
tune to a higher f requency, or to the
lef t to tune to a lower f requency.
Turn the knob right or lef t until the
display reaches the desired
f requency.
The ignition switch must be in
ACCESSORY (I) or ON (II) to
operate the audio system. Turn the
system on by pressing the PWR/
VOL knob, or the AM or FM button.
Adjust the volume by turning the
knob.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM or
FM button. On the FM band, ST will
be displayed if the station is broad-
castinginstereo.Stereo
reproduction on AM is not available.
The SEEK f unction
searches the band for a station with
a strong signal. To activate it, press
either SEEK button ( or ), then
release it. Depending on which
SEEK button you press, the system
scans upward or downward from the
current f requency. It stops when it
finds a station with a strong signal. The SCAN function
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan up
the band for a station with a strong
signal. When it f inds one, it will stop
and play that station for
approximately f ive seconds. If you do
nothing, the system will then scan
f or the next strong station and play
that f or f ive seconds. When it plays a
station that you want to continue
listening to, press the SCAN button
again.
You can use any of f ive methods to
f ind radio stations on the selected
band: TUNE, SEEK, SCAN, AUTO
SELECT, and the preset buttons.
CONT INUED
TUNE
Operating the Radio
SEEKSCAN
Audio System
Comf ort and Convenience Feat ures135

µThe preset f requencies will be lost if
your car’s battery goes dead, is
disconnected, or the radio f use is
removed.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM. Pick the preset button you want
for that station. Press the button
and hold it until you hear a beep. Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button.
To store a f requency: You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band.
UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station. Once a station’s f requency is stored,
simply press and release the proper
preset button to tune to it.
1.
2.
3.
4. Preset
Audio System
Comf ort and Convenience Feat ures136
PWR/VOL
KNOB
AM
BUTTONFM
BUTTON TUNE KNOB
SCAN BUTTON PRESET BUTTONSST INDICATOR
SEEK BUTTONS