recommended oil ACURA RL KA9 1996 Service Repair Manual

Lubrication Points

For the details of lubrication points and types of lubricants to be applied, refer to the Illustrated Index and various work

procedures (such as Assembly/Reassembly, Replacement, Overhaul, Installation, etc.) contained in each section.

No.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22
LUBRICATION POINTS

Engine

Transmission

Brake line (Includes ABS line)

Power steering gearbox

Steering boots

Throttle cable end

Steering ball joints

Shift lever (Automatic transmission)

Pedal linkage

Intermediate shaft

Brake master cylinder pushrod

Fuel
fill
lid

Battery terminals

Trunk hinges and latch

Door hinges upper and lower

Door opening detents

Hood hinges and hood latch

Brake line joints (Front and rear wheelhouse)

Caliper Piston boot, caliper

Pins and boots

Power steering system

Differential

A/C compressor

API SERVICE LABEL API CERTIFICATION SEAL
LUBRICANT

API Service Grade: Use SJ "Energy Conserving" grade oil.

The oil container may also display the API Certification

seal shown below. Make sure it says "For Gasoline

Engines."

SAE Viscosity: See chart below.

Honda ATF-Z1 (ATF)*1

Genuine Honda DOT3 brake fluid*2

Steering grease P/N 08733 - B070E

Multi-purpose grease

Honda White Lithium Grease

Rust preventive

Silicone grease

Genuine Honda power steering fluid*3

Hypoid gear Oil API GL4 or GL5

Viscosity:

at above -18°C (0°F): SAE 90

at less than -18°C (0°F): SAE 80W-90

Compressor oil:

DENSO: ND-OIL8 (P/N) 38897 - PR7 - A01 AH or 38899 -

PR7-A01)

(For Refrigerant: HFC-134a (R-134a))

Recommended engine oil

viscosity for ambient

temperature ranges

*1: Always use Honda ATF-Z1 (ATF). Using a non-Honda ATF can affect shift quality.

*2: Always use Genuine Honda DOT3 Brake Fluid. Using a non-Honda brake fluid can cause corrosion and decrease the

life of the system.

*3: Always use Genuine Honda Power Steering Fluid. Using any other type of power steering fluid or automatic transmis-

sion fluid can cause increased wear and poor steering in cold weather.ProCarManuals.com

Maintenance

Differential Oil

NOTE: Check the differential oil with engine OFF, and

the vehicle on level ground.

1. Remove the oil filler plug, then check the level and

condition of the oil.

WASHER

Replace.

Proper Lever

OIL FILLER PLUG

44 N-m (4.5 kgf-m, 33 Ibf-ft)

WASHER Replace.

2. The oil level must be up to the fill hole. If it is below

the hole, add oil until it runs out, then reinstall the

oil filler plug with a new washer.

3. If the differential oil is dirty, remove the drain plug,

and drain the oil.

DRAIN PLUG

39 N-m (4.0 kgf-m, 29 Ibf-ft)

WASHER Replace.

OIL FILLER PLUG

44 N-m (4.5 kgf-m, 33 Ibf-ft)

4. Reinstall the drain plug with a new washer, and refill

the differential with the recommended oil to the

proper level.

NOTE:

The drain plug washer should be replaced at every

oil change.

Clean the drain plug before reinstalling.
5. Reinstall the oil filler plug with a new washer.

Oil Capacity

1.05 (1.11 US qt, 0.92 Imp qt) at oil change

1.10 (1.16 US qt, 0.97 Imp qt) at overhaul

Recommended oil:

Hypoid gear oil

API Classification GL4 or GL5

viscosity:

SAE 90 above 0°F (-18°C)

SAE 80 W - 90 below 0°F (-18°C)ProCarManuals.com