change time Acura TSX 2007 Owner's Guide

With ‘‘WIPER SETUP’’ shown on the
multi-inf ormation display, press the
SEL/RESET button on the steering
wheel. The display changes to
‘‘FRONT WIPER ACTION’’ as
shown above.
Press the SEL/RESET button, then
press the INFO button.Each time you press the INFO
button, the display changes f rom
‘‘WITH VEH SPD,’’ to
‘‘INTERMITTENT,’’ and then to
‘‘EXIT.’’
Press the INFO button to select
‘‘WITH VEH SPD’’ or
‘‘INTERMITTENT,’’ and enter your
selection by pressing the SEL/
RESET button.
When ‘‘WIPER SETUP’’ is shown on
the multi-information display, the
action of the windshield wipers can
be changed. To do this, ref er to the
f ollowing procedure.
CONT INUED
Wiper SetupFront Wiper A ct ion
Multi-Inf ormation Display
Inst rument s and Cont rols
117

µ
µ µ
µ
µ µ
µ
µ
µ Push
the right lever up or down to
select a position.
The wipers run at high
speed until you release the lever.
The wipers are not activated. The
wipers run at low speed.
The wipers run at high speed.
The length of the wiper
interval is varied automatically
according to the vehicle’s speed.
Vary the delay by turning the INT
TIME ring. If you turn it to the
shortest delay, the wiper speed will
increase to low speed operation
when the vehic le speed exceeds 12
mph (20 km/h). Pull
the
wiper control lever toward you, and
hold it. The washers spray until you
release the lever. The wipers run at
low speed, then complete one more
sweep after you release the lever.
To change the ‘‘FRONT WIPER
ACTION’’ setting, see page .
MIST
OFF
INT Intermittent
LO Low speed
HI High speed
Windshield washers
1.
2.
3.
4.
5.
6.
117
MIST
OFF
LO
HI
INT Windshield Washer
Windshield Wipers and Washers
120

µ To switch from low
beams to high beams, push the left
lever forward until you hear a click.
The high beam indicator will come
on (see page ). Pull it back to
return to low beams. To flash the
high beams, pull the lever back
lightly, then release it. The high
beams will stay on as long as you
hold the lever back.
Turn the fog lights on and off by
turning the switch next to the
headlight switch.
You can use the fog lights only when
the headlights are on low beam.
They will go off when you turn the
headlights off or onto high beam. This
feature turns off the headlights,
parking lights, taillights, and license
plate lights within 15 seconds of
removing the key from the ignition
switch and closing the driver’s door.
You can change this 15 second timer
to 0, 30, or 60 seconds (see page ). With the headlight switch in the off
or position, the high beam
headlights and the high beam
indicator come on with reduced
brightness when you turn the
ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
This feature activates if you leave
the headlight switch in the or
position, remove the key, then
open and close the driver’s door.
If you remove the key f rom the
ignition switch with the headlight
switch on, but do not open the door,
the lights will turn of f af ter 10
minutes. The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, you will hear a lights-on
reminder chime.
66
108
Automatic Lighting Of f Feature
High Beams
Fog Lights (Canadian Models) Daytime Running L ights
Headlights, Automatic Lighting Of f Feature, Daytime Running Lights
122

Each front door has a master door
lock switch. Either switch locks and
unlocks all doors. On the driver’s
door, push the top of the master
door lock switch to lock all doors.
Push the bottom to unlock them.
Each
door has a lock tab on the top.
Push the tab down to lock the door
and pull it up to unlock. All
doors can be locked from the
outsidebyusingthekeyinthe
driver’s door. To unlock only the
driver’s door or all doors (depending
on the ‘‘DOOR LOCK MODE’’
setting), insert the key, turn the key,
and release it. The remaining doors
unlock when you turn the key a
second time within a few seconds.
To change this setting, see page .
Youcanopenorclosethewindows
by using the key in the driver’s door
(see page ).
To lock the passenger’s door when
getting out of the vehicle, push the
lock tab down and close the door. To
lock the driver’s door, remove the
key f rom the ignition switch and
push the lock tab down or push the
top of the master switch, then close
the door. 149
111
CONT INUED
Power Door L ocks
Door L ocks
Inst rument s and Cont rols
129
LOCK TAB
MASTER DOOR LOCK SWITCH
Unlock
Lock
DRIVER’S DOOR

µ
µ Pressthisbuttononce
to unlock the driver’s door or all the
doors (depending on the ‘‘DOOR
LOCK MODE’’ setting). Press it
twice to unlock the other doors.
Some exterior lights will flash twice
each time you press the button.
The ceiling light (if the ceiling light
switch is in the Door Activated
position) will come on when you
press the UNLOCK button. If you do
not open any doors within 30
seconds (or whatever setting the
‘‘INTERIOR LIGHT DIMMING
TIME’’issetto),thelightfadesout.
If you relock the doors with the
remote transmitter before 30
seconds have elapsed, the light will
go off immediatel y.
To change the ‘‘DOOR LOCK
MODE’’ setting, see page .
When
the key is in the ignition
switch, the functions of each button
are disabled.
Press this button once to
lock all doors. Some exterior lights
will flash. When you push LOCK
twice within 5 seconds, you will hear
a horn (depending on the ‘‘KEYLESS
LOCK ACKNOWLEDGEMENT’’
setting) to verify that the doors are
locked and the security system has
set. The Lock button will not work this
way if any door is not fully
closed.
You can open and close all power
windows from outside the vehicle
with the key. With the remote
transmitter, you can open the
windows. Refer to Power Windows
on page .
To
change the ‘‘KEYLESS LOCK
ACKNOWLEDGEMENT’’ setting,
see page .
149113
111
CONT INUED
UNL OCK
LOCK
Remote Transmitter
Inst rument s and Cont rols
131
PANIC
BUTTON TRUNK
RELEASE
BUTTON LOCK
BUTTON
UNLOCK
BUTTON

µµ
To
change the ‘‘INTERIOR LIGHT
DIMMING TIME,’’ see page .
If you unlock the doors with the
remote transmitter, but do not open
anydoorswithin30seconds,the
doors automatically relock and the
security system sets. To change this
setting, refer to ‘‘SECURITY
RELOCK TIMER’’ on page .
Each remote transmitter also
activates the Driving Position
Memory System and changes the
‘‘MEMORY POSITION LINK’’
setting according to that remote (see
page ).
Pressthisbuttonfor
about 1 second to attract attention;
thehornwillsoundandtheexterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position.
Pressthisbuttonfor
about 1 second to open the trunk.
You cannot open the trunk if the key
is in the ignition switch.
142
106
115 Recalling a Memorized Driving
Position
PA NIC
TRUNK
Remote Transmitter
132
DRIVER 1 REMOTE DRIVER 2 REMOTE

The rear ceiling light has a three-
position switch. In the OFF position,
the light does not come on. In the
Door Activated position, the ceiling
lightcomesonwhenyouopenany
door. After all doors are closed
tightly, the light fades out in about
30 seconds. In the ON position, the
ceiling light stays on continuously. The
front ceiling lights have a two-
position switch. In the Door
Acti vated position, the lights come
on when you open any door. In the
OFF position, the lights do not come
on. In
the Door Activated position, the
light comes on when you:
After all doors are closed tightly, the
light dims slightly, then fades out in
about 30 seconds.
Open
any door.
Remove the key from the ignition
switch.
Unlock the doors with the key,
locktabonthedriver’sdoor,
master door lock switch, or
remote transmitter.
If you leave any door open without
the key in the ignition switch, the
ceiling light will go off after 3
minutes.
Turn on the front ceiling lights by
pushing the lens. Push the lens again
to turn if off. You can use these
lights at all times. To change the ‘‘INTERIOR LIGHT
DIMMING TIME,’’ see page . 106
Ceiling L ight
Interior Lights
Inst rument s and Cont rols
153
DOOR ACTIVATED
ON
OFF DOOR ACTIVATED
Front
Rear

The courtesy light between the
spotlights comes on when you turn
the parking lights on. To adjust its
brightness, turn the select/reset
knob on the instrument panel. The
courtesy lights in the front
doors and around the ignition switch
come on when you open any door,
remove key from the ignition switch,
or unlock the driver’s door.
After all doors are closed tightly, the
light dims slightly, then fades out in
about 30 seconds.
To change the ‘‘INTERIOR LIGHT
DIMMING TIME,’’ see page . 106
Courtesy L ight
Individual Interior L ights
Interior Lights
154
COURTESY LIGHT

µ
µ Ifyouwanttoadjustthesoundwhile
the radio or CD is playing, push the
AUDIO DISPLAY button and then
push the TUNE/SOUND knob or
touch the SOUND icon in the display.
The current setting is shown on the
display.
You select which of these you want
to adjust by pressing the TUNE/
SOUND knob. The mode changes
from BASS to TREBLE to FADER to
BALANCE,andthenbacktothe
selected audio mode, each time you
press the knob. Turn the knob to
adjust the setting to your liking.
When the level reaches the center,
you will see ‘‘ ’’ in the display.
The system will automatically return
the display to the selected audio
mode about 5 seconds af ter you stop
adjusting a mode.
Bass, Treble, Balance, and Fader are
each adjustable.
These two
modes adjust the strength of the
sound coming f rom each speaker.
BAL adjusts the side-to-side strength,
while FAD adjusts the f ront-to-back
strength.
Use the TRE/BAS
modes to adjust the tone to your
liking.
On vehicles without navigation system On vehicles with navigation system
CONT INUED
Adjusting the Sound
Balance/Fader
Treble/Bass
Features
175

´µ
You select which of these you want
to adjust by pressing the TUNE/
SOUND knob. The mode changes
from BASS to TREBLE to FADER to
BALANCE,andthenbacktothe
selected audio mode, each time you
press the button. You can also select
themodebytouchingthe
adjustment bar on the display
directly. To adjust the TREBLE and BASS,
touch or on each side of the
TREBLE or BASS adjustment bar.
The adjustment bar shows you the
current setting.
The Left/Right BALANCE adjusts
the side-to-side strength, while
Front/Rear FADER adjust the front-
to-back strength. To adjust the Left/
Right BALANCE, touch the ‘‘L’’ or
‘‘R’’ icon. To adjust the Front/Rear
FADER, touch the ‘‘FR’’ or ‘‘RR’’ icon.
The system will automatically return
the display to the selected audio
mode about 5 seconds af ter you stop
adjusting a mode.
Adjusting the Sound
176
ADJUSTMENT BARS