change time Acura TSX 2007 Owner's Manual

T he inf ormation and specif ications included
in this publication were in ef f ect at the time
of approval f or printing. Honda Motor Co.,
Ltd. reserves the right, however, to
discontinue or change specif ications or
design at any time without notice and
without incurring any obligation whatsoever. T his owner’s manual should be considered
a permanent part of the vehicle and should
remain with the vehicle when it is sold.
T his owner’s manual covers all models of
theTSX.Youmayfinddescriptionsof
equipment and f eatures that are not on your
particular model.
Owner’s Identif ication
OWNER
ADDRESS
V. I. N.
DELIVERY DATE
DEALER NAMEDEALER NO.
ADDRESS
OWNER’S SIGNATURE
DEALER’S SIGNATURE
STREET
CITY STATE/PROVINCE ZIP CODE/
POSTAL CODE
(Date sold to original retail purchaser)
STREET
CITY STATE/PROVINCE ZIP CODE/
POSTAL CODE

This indicator has three functions:
Itcomesonasareminderthatyou
have turned off the vehicle
stability assist (VSA) system.
It flashes when VSA is active (see
page ).
It comes on along with the VSA
system indicator if there is a
problem with the VSA system.
You will also see a ‘‘CHECK VSA
SYSTEM’’ message on the multi-
information display (see page ).
This indicator normally comes on for
a few seconds when you turn the
ignition switch to the ON (II)
position. For more information, see
page . When
you press the hazard warning
button, both turn signals blink. All
turn signals on the outside of the
vehicle should flash. This
indicator normally comes on for
a few seconds when you turn the
ignition switch to the ON (II)
position. If this indicator comes on at
any other time, there is a problem in
theABS.Ifthishappens,takethe
vehicle to your dealer to have it
checked. With this indicator on, your
vehicle still has normal braking
ability but no anti-lock function. You
will also see a ‘‘CHECK ABS
SYSTEM’’ message on the multi-
information display (see page ).
For more information, see page .
The
left or right turn signal indicator
blinks when you signal a lane change
or turn. If an indicator does not blink
or blinks rapidly, it usually means
one of the turn signal bulbs is
burned out (see pages and ).
Replace the bulb as soon as possible,
since other drivers cannot see that
you are signaling.
1.
2.
3.
262
82
262 83
255
302300
Instrument Panel Indicators
Turn Signal and
Hazard Warning
Indicators
VSA A ctivation Indicator
A nti-lock Brake System
(A BS) Indicator
Inst rument s and Cont rols
65

RANGE: The estimated distance
you can travel on the fuel
remaining in the tank. This
distance is estimated from the fuel
economy you received over the
last several miles, so it will vary
with changes in speed, traffic, etc.
ELAPSED TIME: The time
trave led since you last reset the
trip computer.
AVG. SPEED: The average speed
you are traveling.
TIRE PRESSURE MONITOR:
You can see the pressure of each
tire in this monitor. If the tire
pressu re is low on one or more
tires, inflate them to the correct
pressure. For more information,
see page .
The
primary display always shows its
default setting, ‘‘INST. MPG’’ (U.S.
models) or ‘‘INST. L/100 km’’
(Canadian models) even if you press
the INFO button. It only changes the
secondary display. You can
customize this setting to your liking
(see page ).
The upper segment is divided into
two displays; primary and secondary.
After you turn the ignition switch to
the ON (II) position, press the INFO
button on the steering wheel or the
IN FO knob in the instrument panel.
What you last selected appears on
the secondary display of the trip
computer. Pressing the INFO
button/knob repeatedly changes the
display as shown in the example on
the previous page. Messages in the trip computer
include:
When you turn the ignition switch
to the ON (II) position, ELAPSED
TIME is reset.
INST.MPG(U.S.models)/
INST.L/100 km (Canadian
models): Your vehicle’s current
f uel mileage.
AVG. FUEL A/AVG. FUEL B:
Your vehicle’s average fuel
economy since you last reset the
Trip A or Trip B. When you select
Trip B in the lower segment by
pressing the SEL/RESET button
on the steering wheel or select/
reset knob in the instrument panel,
the AVG. FUEL B appears in the
secondary display. 102
258
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
71
INFO KNOBINFO BUTTON

You can also change the display by
pushing the select/reset knob in the
instrument panel.
When you turn the ignition switch to
the ON (II) position, what you last
selected is displayed. While
a trip meter is displayed, you
can change the display between
‘‘Trip A’’ and ‘‘Trip B’’ by pressing
the SEL/RESET button on the
steering wheel, or the select/reset
knob in the instrument panel.
To reset a trip meter, display it, and
press and hold the SEL/RESET
button or select/reset knob until the
number resets to ‘‘0.0.’’ When you
reset ‘‘Trip B’’ , ‘‘AVG. FUEL B’’ is
also reset. If you reset ‘‘Trip A’’,
‘‘AVG. FUEL A’’ and ‘‘AVG. SPEED’’
willberesetatthesametime.
In
the lower segment, each time you
press the SEL/RESET button on the
steering wheel, the display changes
from ‘‘Trip A/Odome ter’’ to ‘‘Trip A/
Outside Temperature’’ to ‘‘Trip B/
Outside Temperature’’ to ‘‘Engine
OilLife,’’andthenbacktothe
‘‘Trip A/Odometer’’ as shown on
page . 70
Multi-Inf ormation Display
Trip Meter
72
U.S.model is shown
SELECT/RESET
KNOB
SEL/RESET
BUTTON
LOWER SEGMENT

When the engine oil life reaches 15 %,
the display shows ‘‘SERVICE DUE
SOON’’ and the code for the
maintenance items to be performed.
When the engine oil life reaches 5 %,
the display shows ‘‘SERVICE DUE
NOW’’ along with the same
maintenance items. Have
your dealer do the indicated
maintenance as soon as you see this
message, and have them reset the
display after completing the service.
If you do not perform the indicated
maintenance or do not reset the
display, the message changes to
‘‘SERVICE PAST DUE’’ when the
engine oil life becomes 0 %. These
messages appear on the multi-
info rmation display each time you
turn the ignition switch to the ON
(II) position.
For more information about
Maintenance Messages, see
‘‘ ’’ on page
.
Also refer to page for important
maintenance saf ety precautions. 272
274
Multi-Inf ormation Display
Maintenance Messages
Maintenance Minder
74
U.S.model is shown

To change the settings, stop the
vehicle, and make sure to set the
parking brake and put the
transmission in Park (A/T) or
neutral (M/T). If you try to enter the
customizing mode while the vehicle
is moving, the above message
appears and you cannot change the
settings. The
first customizing menu is:
DEFAULT ALL
CHANGE
SETTING
Everytimeyoupressthe INFO
button, the display cycles from
‘‘CHANGE SETTING,’’ ‘‘DEFAULT
ALL,’’ ‘‘EXIT’’ and then back to
‘‘CHANGE SETTING.’’ Press the
SEL/RESET button to enter your
selection.
If you want the settings as they were
when the vehicle left the factory,
select ‘‘DEFAULT ALL,’’ as
described on page . If
you want to change any vehicle
control settings, select ‘‘CHANGE
SETTING,’’ and follow the
instructions on page .
You can also use the select/reset
knob in the instrument panel. Turn
the knob to select a setting and press
it to enter your selection. If you do not make any changes,
select ‘‘EXIT,’’ the display returns to
normal display.
90 92
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
87
AT model MT model

ÎÎÎ
Î Î
Î
Î
µ™¶ Ù´
µ™¶ Ù´
Î
LANGUAGE
SELECTION
ADJUST
OUTSIDE TEMP.
DISPLAY
TRIP A & AVG. FUEL
RESET with REFUEL
ELAP. TIME RESET
CONDITION
PRIMARY DISP
SELECTION
MEMORY POSITION
LINK Description
Changes the language used in the display.
Changes the outside temperature reading above or
below its current reading.
Causes trip meter A and the average fuel economy
to reset when you refuel.
Resets the elapsed time of your current trip.
Changes the trip computer’s main display from its
default setting.
Causes the driver’s seat position to a stored in
memory.
Customize
Group
METER SETUP
(P.93)
POSITION SETUP
(P.104) Customize
Menu Customize Setup
ENGLISH
FRENCH
SPANISH 5°F 0 F 5°F
3°C 0 C 3°C
ON
OFF
IGN RESET
TRIP A RESET
TRIP B RESET
INST. FUEL
AVG. FUEL
RANGE
ELAPSED TIME
AVG. SPEED
ON
OFF Page
94
96
98
100
102
104
: Default setting
Multi-Inf ormation Display
88

Î
ÎÎ
Î
Î Î
Î
Description
Changes how long (in seconds) the interior lights
stay on after you close the doors.
Changes how long (in seconds) the exterior lights
stay on after you close the driver’s door.
Changes which doors unlock with the remote
transmitter when the button is pushed one time.
The exterior lights flash each time you press the
LOCK or UNLOCK button. A horn will also sound
when you press the LOCK button twice.
Changes how long it takes (in seconds) for the
doors to relock and the security system to set after
you unlock but do not open the door.
Changes the windshield wiper operation between
two settings when the wiper switch is in the INT
position. Customize
Setup
15 sec
30 sec
60 sec
0sec
15 sec
30 sec
60 sec
DRIVER DOOR
ALL DOORS
ON
OFF
30 sec
60 sec
90 sec
WITH VEH SPD
INTERMITTENT Page
106
108
111
113
115
117
Customize
Group
LIGHTING SETUP
(P.106)
DOOR · WINDOW
SETUP
(P.110)
WIPER SETUP
(P.117) Customize
Menu
INTERIOR LIGHT
DIMMING T IME
HEADLIGHT AUT O OFF
TIMER
DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGEMENT
SECURITY RELOCK
TIMER
FRONT WIPER ACTION
: Default setting
Multi-Inf ormation Display
Inst rument s and Cont rols
89

If you want to set the customizable
vehicle control settings to the default
setting, press the INFO button on
the steering wheel until ‘‘DEFAULT
ALL’’ is displayed.
Press the SEL/RESET button to
enter ‘‘DEFAULT ALL.’’ You can
change the display between
‘‘CANCEL,’’ ‘‘OK’’ and ‘‘EXIT’’ each
time you press the INFO button.If you want to cancel ‘‘DEFAULT
ALL,’’ press the SEL/RESET button
while ‘‘CANCEL’’ is shown. The
display goes back to ‘‘CUSTOMIZE
ENTRY.’’
To set the def ault settings, press the
INFO button until the display
changesasshownabove.Pressthe
SEL/RESET button to select
‘‘DEFAULT ALL.’’
DEFAUL T AL L
Multi-Inf ormation Display
90

While the multi-information display
is showing ‘‘CHANGE SETTING,’’
press the SEL/RESET button. The
display will start showing the initial
‘‘CUSTOMIZE GROUP.’’ Each time
you press the INFO button, the
display changes as shown in the next
column. Press the INFO button until
you see the setup you want to
customize, and press the SEL/
RESET button to enter your
selection. You can customize some of the
vehicle control settings to your
pref erence. Here are the settings
you can customize:METER SETUP
POSITION SETUP
LIGHTING SETUP
DOOR/WINDOW SETUP
WIPER SETUP
Change Setting
Multi-Inf ormation Display
92
: Press SEL/RESET Button.
: Press the INFO Button.