battery ACURA ZDX 2010 User Guide

To replace the battery:1. Remove the screw at the base of the transmitter with a small
Phillips-head screwdriver.
NOTE: Be careful when removing
this screw as the head of the screw
can strip out.
2. Separate the keypad from the transmitter by pushing any button
from outside.
3. Place a cloth on the edge of thekeypad to prevent scratches, and
remove the upper half by carefully
prying on the edge with a small
flat-tip screwdriver. 4. Remove the old battery and note
the polarity. Make sure the
polarity of the new battery is the
same (－ side facing up), then
insert it in the keypad.
An improperly disposed of battery
can hurt the environment.
Always confirm local regulations
for battery disposal.
5. Snap the two halves of the keypad, then install the parts in reverse
order.
SCREW KEYPAD
BATTERY
CONTINUED
Remote Transmitter
159
Instruments and Controls
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

In the HI setting, the heater turns off
when the seat gets warm, and turns
back on after the seat's temperature
drops.
In the LO setting, the heater runs
continuously. It does not cycle with
temperature changes.
Follow these precautions when using
the seat heaters:●Use the HI setting only to heat the
seats quickly, because it draws
large amounts of current from the
battery.●If the engine is left idling for an
extended period, do not use the
seat heaters even on the LO
setting. It can weaken the battery,
causing hard starting.
A multi-information display message
may inform you when the battery
charge is getting low. See page 85 for
more information. Front Seat Heaters and Seat
Ventilation
On models with adaptive cruise control
(ACC)Both front seats are equipped with
seat heaters and an air ventilation
system. The passenger seat only has
heaters in the seat bottom because of
the side airbag system.
You must select the ON mode by
operating the engine start/stop
button (see page 194) to use the
heaters and the air ventilation
system.
Passenger's
seat
HEATERS Driver's
seat
SEAT VENTILATION
BUTTONINDICATORS
SEAT HEATER
BUTTON
Front Seat Heaters, Front Seat Heaters and Seat Ventilation16809/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

To use the heaters, press the seat
heater button. The indicator (red)
next to the button will come on.
There are four settings in the
heaters:
HI－Three indicators on.
MID －Two indicators on.
LO －One indicator on.
OFF －All indicators off.
When you press the seat heater
button once, the heater is set to HI.
After the seat reaches a comfortable
temperature, select MID or LOW by
pressing the seat heater button. This
will keep the seat warm. To shut
down the heater, press the seat
heater button until the indicators go
off. To ventilate the seat, press the seat
ventilation button. The indicator
(blue) next to the button will come
on. The air ventilation system has
four settings:
HI
－Three indicators on.
MID －Two indicators on.
LO －One indicator on.
OFF －All indicators off.
When you press the seat ventilation
button once, the system is set to HI.
To change to the lower mode, press
the seat ventilation button. To turn
the air ventilation off, press the seat
ventilation button until the indicators
go off. Follow these precautions whenever
you use the seat heaters and the seat
ventilation:
●Use the HI setting only to heat or
to ventilate the seats quickly,
because it draws large amounts of
current from the battery.●If the engine is left idling for an
extended period, do not use the
seat heaters or the seat ventilation,
even on the LO setting. It can
weaken the battery, causing hard
starting.
A multi-information display message
may inform you when the battery
charge is getting low. See page 85 for
more information.
Front Seat Heaters and Seat Ventilation
169
Instruments and Controls
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

Follow these precautions whenever
you use the seat heaters:●Use the HI setting only to heat the
seats quickly, because it draws
large amounts of current from the
battery.●If the engine is left idling for an
extended period, do not use the
seat heaters even on the LO
setting. It can weaken the battery,
causing hard starting.
A multi-information display message
may inform you when the battery
charge is getting low. See page 85 for
more information. Power Windows
Turn the ignition switch to the ON
(II) position to raise or lower any
window. To open a window, push the
switch down and hold it. Release the
switch when you want the window to
stop. Pull back on the switch and
hold it to close the window.Models equipped with the keyless
access system have an engine start/
stop button instead of an ignition
switch. ON mode is the equivalent of
ON (II). For more information, see
pages 194 and 196.
Closing a power window on
someone's hands or fingers can
cause serious injury.
Make sure your passengers are
away from the windows before
closing them.
AUTO －To open either front
window fully, push the window
switch firmly down to the second
detent, then release it. The window
automatically goes down all the way.
To stop the window from going all
the way down, pull back on the
window switch briefly.
DRIVER'S WINDOW
SWITCH MAIN SWITCH
FRONT PASSENGER'S
WINDOW SWITCH
CONTINUED
Rear Seat Heaters (Canadian models), Power Windows
171
Instruments and Controls
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

On models with navigation systemYour vehicle has a keyless access
system. This system allows you to
operate the vehicle without an
ignition key. When you carry the
remote with you, you can lock/
unlock the door(s), unlock the
tailgate, and start the engine.
The system may not work if:●The battery of the remote is weak.●There is strong electrical current
nearby.●You carry a cell phone, a laptop
computer, or other electrical
device near the remote.●The remote is covered by metal.●A vehicle is being operated with a
transmitter nearby.●When the remote battery is dead.●When the vehicle battery is dead.Each keyless access remote has the
built-in key. This key is used to lock/
unlock the doors when the remote
battery becomes weak and the power
door lock/unlock operation is
disabled. You cannot start the engine
with this key.
Make sure the driver always carries
the remote/built-in key set.
Protect the remote and the built-in
key from direct sunlight, high
temperature, and high humidity.
Do not drop the remote or the built-
in key, and do not set heavy objects
on them.
Keep the remote and the built-in key
away from liquids. If they get wet,
dry them immediately with a soft
cloth.
The built-in keys do not contain
batteries.
Always keep the remote and the
built-in key away from any magnetic
material.
You should have received a key
number tag with your built-in key.
You will need this key number if you
ever have to get a lost key replaced.
Use only Acura-approved key blanks.
CONTINUED
Keyless Access System
183
Instruments and Controls
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

If you do not open any of the doors
within 30 seconds, they will
automatically relock.
To change the‘‘SECURITY RELOCK
TIMER ’’setting, see page 134.
If a remote is within operating range
while you wash your vehicle or when
it is raining heavily, the door sensors
may respond by unlocking the doors. Each unlock sensor does not operate
when:
●The remote is not within the
operating range.●The remote is too close to the
vehicle.●When the doors are unlocked.●The remote battery is dead.●The vehicle battery is dead.Locking the Doors
When you press the door lock button
on the front door, all the doors and
the tailgate will lock.
Before locking the doors, make sure
the remote is not inside the vehicle.
DOOR LOCK BUTTON
Keyless Access System18609/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

When you lock the doors, some
exterior lights blink and the system
beeps once. If no exterior lights blink
and/or no beeper sounds, check to
see if the tailgate or hood is open.
To change the‘‘KEYLESS ACCESS
LIGHT FLASH ’’setting, see page
120.
To change the ‘‘KEYLESS ACCESS
BEEP ’’setting, see page 121.
Within 2 seconds of pressing the
door lock button to lock the doors or
locking the doors with remote, pull
the handle to make sure the doors
are actually locked. The door unlock
sensors will not operate for about 2
seconds after the doors are locked. The door lock button does not work
if:
●The remote is not within the
operating range.●Any door is open.●The power mode is not set to
VEHICLE OFF (LOCK).●The remote is in the keyless
access slot.●The remote is too close to the
vehicle.●The remote battery is dead.●The vehicle battery is dead.
Door Lock PreventionIf you open the driver's door, pull its
lock tab rearward on the door, and
shut it when the remote is inside the
vehicle, the driver's door will unlock.
Make sure you carry the remote with
you when you lock the doors.
This function is also activated on the
front passenger's door. If you open
the front passenger's door, and shut
it after pulling its lock tab rearward
when the remote is inside the
vehicle, all doors will unlock.
CONTINUED
Keyless Access System
187
Instruments and Controls
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

Replacing the Remote BatteryReplace the battery if necessary.
Battery type: CR2032
To replace the battery:1. Remove the built-in key (see page 207).
2. Remove the upper half by carefully prying on the edge with a coin.
3. Replace the old battery with newbattery. Place the battery so the ＋
side is facing up. Snap the two
halves of the remote case back
together.
An improperly disposed of battery
can hurt the environment. Always
confirm local regulations for battery
disposal.
As required by the FCC: This device complies with Part 15 ofthe FCC rules. Operation is subjectto the following two conditions: (1)
This device may not cause harmfulinterference, and (2) this device mustaccept any interference received,including interference that maycause undesired operation.
Changes or modifications notexpressly approved by the partyresponsible for compliance could
void the user's authority to operatethe equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the followingtwo conditions: (1) this device maynot cause interference, and (2) thisdevice must accept any interference
that may cause undesired operationof the device.
CONTINUED
Keyless Access System
191
Instruments and Controls
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

If the steering wheel is locked, the
engine cannot start. The multi-
information display shows you the
above message and the indicator in
the engine start/stop button blinks.
To unlock the steering wheel, apply
force by turning it left and right while
pressing the engine start/stop button
at the same time.NOTE:
If the keyless access remote battery
dies, you may have to use the built-in
key to unlock/lock the vehicle. The
built-in key is stored inside the
keyless access remote (see page
207).
After entering the vehicle, insert the
keyless access remote into the slot to
start the engine (see page 205).
Stopping the Engine
To turn the vehicle off when the
vehicle is completely stopped, shift to
Park (P), then press the engine
start/stop button. The engine stops
and the power mode switches from
ON to VEHICLE OFF (LOCK).
TO UNLOCK WHEELKeyless Access System19809/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com

Even when the remote is inside the
vehicle, the beeper may sound when
the location of the remote is not
detected due to surrounding
conditions. It is not a failure. Make
sure that you carry the remote with
you.
The outside beeper sounds when the
power mode is in ACCESSORY, and
a door is opened, then closed.
Keyless Remote Low BatteryThe battery in the remote normally
lasts about 2 years. To ensure
maximum battery life, do not store
the remote close to electrical devices
such as computers or TVs. When the
multi-information display shows
‘‘CHANGE KEYLESS REMOTE
BATTERY, ’’replace the battery as
soon as possible (see page 191). If the remote battery becomes weak
and the power door lock/unlock
operation is disabled, you should
insert the remote into the keyless
access remote slot to set the power
mode and start the engine. After
inserting the remote to the slot,
operate the engine start/stop button
as previously described (see pages
194 and 195). For more information
on the keyless access slot, see page
205.
Inserting the remote does not charge
the remote battery. You should
replace the battery as soon as
possible.
Keyless Access System20209/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
ProCarManuals.com