remove seats Acura ZDX 2012 Owner's Manual
[x] Cancel search | Manufacturer: ACURA, Model Year: 2012, Model line: ZDX, Model: Acura ZDX 2012Pages: 645, PDF Size: 16.36 MB
Page 22 of 645
If necessary, pull up on the belt again
to remove any slack, then check that
the belt rests across the center of
your chest and over your shoulder.
This spreads the forces of a crash
over the strongest bones in your
upper body.
Improperly positioning the seat
belts can cause serious injury
or death in a crash.
Make sure all seat belts are
properly positioned before
driving.If the seat belt touches or crosses
your neck, or if it crosses your arm
instead of your shoulder, you need to
adjust the seat belt anchor height.
The front seats have adjustable seat
belt anchors. To adjust the height of
an anchor, press and hold the release
button and slide the anchor up or
down as needed (it has four
positions).
RELEASE
BUTTON
CONTINUED
Protecting Adults and Teens
17
Driver and Passenger Safety
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
Page 56 of 645
7. Attach the tether strap hook to thetether anchor, then tighten the
strap as instructed by the child
seat maker.
8. Lower the head restraint until it locks in place.
9. Push and pull the child seat forward and from side-to-side to
verify that it is secure. Installing a Child Seat with a Lap/
Shoulder Belt
When not using the LATCH system,
all child seats must be secured to the
vehicle with the lap part of a lap/
shoulder belt.
In addition, the lap/shoulder belts in
all seating positions except the
driver's have a lockable retractor that
must be activated to secure a child
seat.
1. With the child seat in the desired
seating position, route the belt
through the child seat according to
the seat maker's instructions, then
insert the latch plate into the
buckle and remove any slack from
the lap portion of the belt.
CONTINUED
Installing a Child Seat
51
Driver and Passenger Safety
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
Page 169 of 645
Removing the Head RestraintTo remove a front or rear center
head restraint for cleaning or repair,
pull it up as far as it will go. Push the
release button, then pull the restraint
out of the seat-back.
If for some reason you need to
remove the rear outer head restraint,
push the tilt button, then fold the
head restraint backward. Push the
release button, then pull the restraint
out of the seat-back.
Failure to reinstall the head
restraints can result in severe
injury during a crash.
Always replace the head
restraints before driving.
When reinstalling a head restraint,
put the legs back in place. Then
adjust it to the appropriate height
while pressing the release button.
Make sure the head restraint locks in
position when you reinstall it.
Rear Outer TILT BUTTON
RELEASE BUTTON
Seats16409/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
Page 171 of 645
Folding the Rear Seats
The left and right halves can be
folded separately.
Remove any items from the seats
before folding the seat-backs.
1. Store the center seat belt buckleinto the pocket in the rear seat-
back.
2. Lower the head restraints to theirlowest positions.
3. Unlock the seat-back by pulling up the handle on the outer side of
each rear seat-back.
4. Fold the seat-back forward.
HANDLE
Seats16609/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu
Page 474 of 645
Optional Separation Net
The separation net can be used to
hold back soft, lightweight items
stored in the cargo area. Heavy items
should be tied down, as the net may
not prevent them from being thrown
about the vehicle in a crash or a
sudden stop.
Optional Cargo Cover
The cargo cover can be used to cover
the cargo area behind the rear seats.
When the rear seats are folded down,
the cargo cover can be extended over
the larger area. Do not install the
cover over the larger area if the rear
seats are not folded down.Cargo Hooks
To secure cargo, use the four floor
hooks in the cargo area. Make sure
all stored items are secured before
driving.The cargo area carpets are loop-type
construction. If snags occur from
sharp or rough objects, do not pull
the loose threads to remove them.
Cut all loose threads with a scissors
to prevent carpet runs.
CARGO
HOOKS
Carrying Cargo
469
Before Driving
09/10/28 17:15:37 10 ACURA ZDX KA KC New North America Own 50 31SZN600 enu