instrument panel Alfa Romeo 159 2010 Owner handbook (in English)
[x] Cancel search | Manufacturer: ALFA ROMEO, Model Year: 2010, Model line: 159, Model: Alfa Romeo 159 2010Pages: 331, PDF Size: 4.84 MB
Page 124 of 331

122
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
CORRECT USE
OF THE CAR
DASHBOARD
AND
CONTROLS
The car may be equipped with a Tyre
Pressure Monitoring System, which in-
dicates to the driver the tyre pressure
status by two different indications:
“Check tyre pressures” and “Low tyre
pressures”. For a detailed description of
the two indications, see the “Warning
Lights and Messages” section. This sys-
tem consists of a radio-frequency sen-
sor, installed on each wheel (on the rim
inside the tyre) that sends pressure in-
formation to the control unit.
IMPORTANT NOTES
Failure indications will not be stored and
therefore will not be displayed when
turning the engine off and on again. If
failure persists, the control unit will send
warning indications to the instrument
panel only after a few seconds when the
car is moving.
TYRE PRESSURE MONITORING SYSTEM -
T.P.M.S.
(for versions/markets, where provided)
The T.P.M.S. does not
exempt the driver from
checking tyre pressure, includ-
ing the space-saver spare
wheel (for versions/markets,
where provided) at regular in-
tervals.
WARNING
Tyre pressure should be checked with
tyres cold. Should it become necessary
for whatever reason to check pressure
with hot tyres, do not reduce pressure
although it is higher than the prescribed
value but repeat the check when tyres
are cold (see section “Wheels” in sec-
tion “Technical Specifications”).
T.P.M.S. cannot indicate sudden tyre
pressure drops (e.g.: tyre burst). In this
event, brake the car cautiously and
avoid sudden steering.
The T.P.M.S. system requires special
equipment. Consult Alfa Romeo Autho-
rized Services to know what type of ac-
cessories are compatible with the sys-
tem (wheels, wheel caps, etc.). Using
other accessories could cause system
malfunctioning. Due to inflation valve
special characteristics, use only tyre re-
pair sealants approved by Alfa Romeo;
other sealants could cause system mal-
functioning.
083-128 Alfa 159 GB 3-12-2009 14:09 Pagina 122
Page 154 of 331

152
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
CORRECT USE
OF THE CAR
The starter automatically operates until
the engine starts.
With engine off and electronic key in-
serted in the ignition device, it is possi-
ble to operate the automatic ignition
briefly pressing the START/STOPbut-
ton and keeping the clutch pedal
pressed.
In the event of cold weather, we rec-
ommend to wait for warning light
m
turn off before operating the starter.
IMPORTANTIt is possible to start the
engine keeping pressed only the brake
pedal. In that case, automatic start is not
enabled. Then press the START/STOP
button and release it as soon as the en-
gine starts.IMPORTANT
If at start-up the engine turns off, restart
it by pressing the clutch or brake pedal
and then press button START/STOP.
If after a few attempts the engine does
not start, do not insist but contact Alfa
Romeo Authorized Services.
With car started the electronic key is
locked into the ignition device and it can
be removed only after switching the en-
gine off. With car running and key
locked into the ignition device, forced
key removal could damage the ignition
device.Start-up failures, if any, are indicated by
the turning on of the warning light
Y
on the instrument panel (on certain ver-
sions a dedicated message is displayed).
In this case contact Alfa Romeo Autho-
rized Services.
If the engine will not start after pressing
button START/STOP, repeat the
start-up procedure by pressing the oth-
er pedal (clutch or brake).
149-164 Alfa 159 GB 8-04-2009 10:51 Pagina 152
Page 155 of 331

153
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
CORRECT USE
OF THE CAR
Start-up failures
The system can recognise start-up fail-
ures.
In the event of failure, the electronic key
can be removed from the ignition device to
enable the driver to carry out the follow-
ing operations:
❒turn the instrument panel off by
pressing button START/STOPor
removing the electronic key from the
ignition device;
❒start the engine again by pressing the
clutch/brake pedal and button
START/STOP.
IMPORTANT In the event of engine
locking while the car is running, due to
safety reasons it will not be possible to
take the electronic key out of the igni-
tion device. To remove it, press button
START/STOPwith brake pedal (or
clutch pedal) released and car stopped.
HOW TO WARM UP THE
ENGINE AFTER IT HAS
JUST STARTED
(petrol and diesel engines)
Proceed as follows:
❒Drive off slowly, letting the engine
turn at medium revs. Do not acceler-
ate abruptly;
❒Do not drive at full performance for
the initial kilometres. Wait until the
coolant temperature gauge starts
moving.
IMPORTANTAfter a taxing drive, you
should allow the engine to “catch its
breath” before turning it off by letting it
idle to allow the temperature in the en-
gine compartment to fall.
STOPPING THE ENGINE
With car stopped press button START/
STOP. When the engine is off it will be
possible to remove the electronic key
from the ignition device.
In an emergency, and
for safety reasons the
engine can be turned off when
the car is running by pressing
repeatedly (3 times within
2 seconds) or by keeping
pressed button START/STOP
for a few seconds. In this case
the steering lock cannot be en-
gaged.
WARNING
149-164 Alfa 159 GB 8-04-2009 10:51 Pagina 153
Page 157 of 331

155
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND
CONTROLS
CORRECT USE
OF THE CAR
To release the handbrake proceed as fol-
lows:
❒Slightly lift the handbrake Aand
press release button B;
❒Keep button Bpressed and lower the
lever. Warning light
xon the in-
strument panel will turn off.
Press the brake pedal when carrying out
this operation to prevent the car from
moving accidentally.
HANDBRAKE
The handbrake lever A-fig. 2 is locat-
ed between the two front seats. Pull the
handbrake lever Aupwards, until the
car cannot be moved.
With electronic key fitted into the igni-
tion device, the instrument panel warn-
ing light
xwill come on.
IMPORTANT The car shall stop after
a few clicks of the handbrake lever. If
this is not the case, contact Alfa Romeo
Authorized Services to have the hand-
brake adjusted.
A0E0030mfig. 2
PARKING THE CAR
Proceed as follows:
❒Stop the engine and engage the
handbrake;
❒Engage a gear (on a slope, engage
first gear if the car is faced uphill or
reverse if it is faced downhill) and
leave the wheels steered.
Block the wheels with a wedge or a stone
if the car is parked on a steep slope. Do
not leave the electronic key in the igni-
tion switch to prevent draining the bat-
tery.
Never leave children un-
attended in the car. Al-
ways remove the electronic key
from the ignition device when
leaving the car and take it out
with you.
WARNING
149-164 Alfa 159 GB 8-04-2009 10:51 Pagina 155
Page 177 of 331

175
SAFETY
DEVICES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
CORRECT USE
OF THE CAR
DASHBOARD
AND
CONTROLS
WARNING
LIGHTS AND
MESSAGES
EBD SYSTEM
FAILURE
(red)
(amber)
With the engine running the
turning on at the same time of
the
>and xwarning lights (on cer-
tain versions together with the message
on the display) indicates that the EBD
system is inefficient; in this case heavy
braking may cause the rear wheels to
lock before time, with the possibility of
skidding.
Drive with the utmost care to the near-
est Alfa Romeo Authorized Service to
have the system checked.
VDC SYSTEM
(amber)
(for versions/markets,
where provided)
Fitting the key into the ignition device
the warning light turns on, but it should
go off after few seconds.
The warning light flashes when the VDC
cuts in, to alert the driver that the sys-
tem is adapting to the road surface grip
conditions.
VDC deactivation
When the VDC is deactivated manually
(pressing the ASR/VDC button for 2 sec-
onds) (see paragraph “VDC system” in
section “Dashboard and controls”) the
instrument panel warning light turns on
(on certain versions a message is dis-
played).
VDC failure
In case of failure, the VDC system will
deactivate automatically and the in-
strument panel warning light
áwill turn
on glowing steadily (on certain versions
a message will also be displayed). In
this case contact Alfa Romeo Authorized
Services as soon as possible.
ABS SYSTEM
FAILURE (amber)
Fitting the key into the ignition
device the warning light turns on, but
it should go off after few seconds.
The warning light turns on (on certain
versions a dedicated message is dis-
played) when the system is inefficient.
In this case the braking system keeps
its effectiveness unchanged, but without
the potential offered by the ABS system.
Drive carefully and contact Alfa Romeo
Authorized Services as soon as possible.
>
>
xá
165-180 Alfa 159 GB 3-12-2009 14:09 Pagina 175
Page 216 of 331

214
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
CORRECT USE
OF THE CAR
DASHBOARD
AND
CONTROLS
IN AN
EMERGENCY
FUSE SUMMARY TABLE
LIGTHS FUSE AMPERE FIGURE
Right main beam headlight F14 7.5 60
Left main beam headlight F15 7.5 60
Right dipped beam headlight F12 15 56
Left dipped beam headlight F13 15 56
Front fog light F30 15 60
Reversing light/Brake light F35 7.5 56
Third brake light F37 7.5 56
Front/rear ceiling light F39 10 56
Front ceiling light F49 7.5 56
Direction indicators F53 10 56
Hazard lights F53 10 56
USERS FUSE AMPERE FIGURE
Engine housing control unit services F70 (MEGA-FUSE) 150 58
Instrument panel control unit F71 70 58
Additional heater (passenger compartment water heating 600W)
(diesel versions) F72 50 58
Plug pre-heating control unit (diesel versions) F73 60 58
Instrument panel control unit F01 (MAXI-FUSE) 60 60
181-222 Alfa 159 GB 3-12-2009 14:10 Pagina 214
Page 218 of 331

216
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
CORRECT USE
OF THE CAR
DASHBOARD
AND
CONTROLS
IN AN
EMERGENCY
USERS FUSE AMPERE FIGURE
Fuel pump supply F21 20 60
Sound system/radionavigation system power/Blue&Me F23 15 60
Supply + key for relay coils of engine compartment control unit/
dashboard control unit/Body Computer F31 7.5 56
Driver’s door branch point/passenger’s door branch point/
ignition device F32 15 56
Rear left window control/boot node F33 20 56
Rear right window control/boot node F34 20 56
Water in diesel fuel filter sensor/flow meter/Brake light switch/
central console control panel/Cruise Control/AQS sensor F35 7.5 56
Supply of boot node/locks actuators F36 20 56
Positive under key for stop lights/third stop/instrument/
lights direction F37 7.5 56
Boot opening F38 15 56
Supply + battery for air conditioner, ceiling lights, volumetric alarm,
EOBD system diagnostic socket F39 10 56
181-222 Alfa 159 GB 3-12-2009 14:10 Pagina 216
Page 220 of 331

218
SAFETY
DEVICES
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
CORRECT USE
OF THE CAR
DASHBOARD
AND
CONTROLS
IN AN
EMERGENCY
USERS FUSE AMPERE FIGURE
Rear window wiper/Rear lighter F52 15 56
Instrument panel branch point F53 10 56
Amplifier Bose audio system F54 30 62
Front left seat movement control F56 25 62
Driver’s seat warming left F57 7.5 62
Front right seat movement control F60 25 62
Amplifier Bose audio system on rear parcel shelf F61 15 62
Front passenger’ seat warming right F67 7.5 62
Free F58 --- 62
Free F59 --- 62
Free F62 --- 62
Free F63 --- 62
Free F64 --- 62
Free F66 --- 62
Free F68 --- 62
Free F69 --- 62
Free F77 --- 62
Free F78 --- 62
Free F79 --- 62
Free F80 --- 62
181-222 Alfa 159 GB 3-12-2009 14:10 Pagina 218
Page 228 of 331

35 70 105 140 175
●●●●●
●
●●●●●
●●●●●
●●●●●
●
●
●
●
●
●
●●
●●
●●
●
●●●●●
●●●●●
●●●●●
●●
●●●●●
Thousands of km
Check and adjust tappet clearance (1.9 JTDM8v version)
Check and adjust tappet clearance, if required (1.8 140 HP version)
Check exhaust emissions (petrol versions)
Check exhaust emissions/smoke (diesel versions)
Check engine control system operation (through diagnosis socket)
Replace accessory drive belt/s (except 1.8 140 HP version)
Replace accessory drive belt/s (1.8 140 HP version)
Replace timing belt (1.8 140 HP version) (*)
Replace timing belt (1750 TURBO BENZINA version) (*)
Replace timing belt (diesel versions) (*)
Change spark plugs (3.2 JTS and 2.2 JTS Selespeed versions)
Change spark plugs (1.8 140 HP and 1750 TURBO BENZINA versions)
Replace diesel fuel filter (diesel versions)
Change air cleaner cartridge
Change front transmission gear oil (3.2 JTS 4x4 versions)
Change engine oil and oil filter (1.8 140 HP versions) (or every 12 months)
Change engine oil and oil filter (1750 TURBO BENZINA versions) (**)
(or every 12 months)
Change engine oil and oil filter (3.2 JTS and 2.2 JTS Selespeed versions)
(or every 24 months) (***)
Change engine oil and oil filter (diesel versions with DPF) (**)
(or every 24 months)
Change engine oil and oil filter (diesel versions without DPF)
(or every 24 months)
Change brake fluid (or every 24 months)
Change pollen filter (or every 24 months)
(*) Regardless of the km covered, the timing belt shall be replaced every 4 years for particularly demanding use (cold climates, driving in the city,
idling for a long time) or in any case every 5 years.
(**) The engine oil and the filter must be changed when the instrument panel warning light comes on (see “Warning lights and Messages” chapter)
and in all cases every 24 months.
If the car is mainly used for town driving or in particularly harsh climate conditions and has a low annual mileage, the engine oil and filter should
be changed every 12 months.
CAR
MAINTENANCE
DASHBOARD
AND
CONTROLS
CORRECT USE
OF THE CAR
INDEX
TECHNICAL
SPECIFICATIONS
IN AN
EMERGENCY
WARNING
LIGHTS AND
MESSAGES
SAFETY
DEVICES
226
223-248 Alfa 159 GB 3-12-2009 14:11 Pagina 226
Page 238 of 331

BRAKE FLUID fig. 17
Check that the fluid level in the reservoir
is at maximum. Top up with the brake
fluid specified in the table “Fluids and
lubricants” (see section “Technical Spec-
ifications ").
NOTEClean accurately the tank cap A
and the surrounding surface. When
opening the cap take the utmost care to
prevent impurities entering the tank.
When topping up, always use a funnel
with built-in filter with mesh equal to
or lower than 0.12 mm.
A0E0016mfig. 17
Make sure that the high-
ly corrosive brake fluid
does not drip onto the
paintwork. If it does, wash it off
immediately with water.
IMPORTANTFor this operation it is
however recommended to contact Alfa
Romeo Authorised Services.
From time to time, check the instrument
panel warning light
x: pressing on cap
A(with key fitted into the ignition de-
vice) the warning light shall turn on.
IMPORTANTBrake fluid absorbs
moisture. For this reason, if the car is
mainly used in areas with a high degree
of atmospheric humidity, the fluid should
be replaced at more frequent intervals
than specified in the Service schedule.
CAR
MAINTENANCE
DASHBOARD
AND
CONTROLS
CORRECT USE
OF THE CAR
INDEX
TECHNICAL
SPECIFICATIONS
IN AN
EMERGENCY
WARNING
LIGHTS AND
MESSAGES
SAFETY
DEVICES
236
Brake fluid is poisonous
and highly corrosive. In
the event of accidental contact,
wash the parts involved im-
mediately with neutral soap
and water, then rinse thor-
oughly. Call the doctor imme-
diately if the fluid is swal-
lowed.
WARNING
Symbol πon the con-
tainer indicates syn-
thetic brake fluid, distinguish-
ing it from the mineral kind.
Using mineral fluids irre-
versibly damages the special
braking system rubber seals.
WARNING
223-248 Alfa 159 GB 3-12-2009 14:11 Pagina 236