ESP Alfa Romeo 4C 2021 Instructieboek (in Dutch)

USING THE HANDBOOK
Each time direction instructions (left/right or forwards/backwards) about the vehicle are given, these must be understood as regarding an occupant in the driver’s seat.
Special cases not complying with this rule will be specified as appropriate in the text.
The figures in the Owner Handbook are provided by way of example only: this might imply that some details of the image do not correspond to the actual arrangement
of your vehicle. In addition, the Handbook has been conceived considering vehicles with steering wheel on the left side; it is therefore possible that on vehicles with
steering wheel on the right side, the position or construction of some controls is not exactly mirror-like with respect to the figure.
To identify the chapter with the information needed you can consult the index at the end of this Owner Handbook.
Chapters can be rapidly identified with dedicated graphic tabs, at the side of each odd page. A few pages further there is a key for getting to know the chapter order
and the relevant symbols in the tabs. There is anyway a textual indication of the current chapter at the side of each even page.

WARNINGS AND PRECAUTIONS
While reading this Owner Handbook you will find a series of WARNINGS to prevent procedures that could damage your car.
There are also PRECAUTIONSthat must be carefully followed to prevent incorrect use of the components of the vehicle, which could cause
accidents or injuries.
Therefore all WARNINGSand PRECAUTIONSmust always be carefully followed.
WARNINGSand PRECAUTIONSare recalled in the text with the following symbols:
NOTE These symbols, when necessary, are indicated besides the title or at the end of the line and are followed by a number.
That number recalls the corresponding warning at the end of the relevant section.
IMPORTANT
This Owner Handbook describes all Alfa 4C versions. Options, equipment dedicated to specific markets or versions are not explicitly
indicated in the text: as a consequence, you should only consider the information which is related to the trim level, engine and version
that you have purchased. Any content introduced throughout the production of the model, outside the specific request of options at the
time of purchase, will be identified with the wording (where provided).
All data contained in this publication are intended to help you use your vehicle in the best possible way. FCA Italy S.p.A. aims at a
constant improvement of the vehicles produced. For this reason it reserves the right to make changes to the model described for
technical and/or commercial reasons.
For further information, contact a dedicated Alfa Romeo Dealership.
VEHICLE CHANGES / ALTERATIONS
IMPORTANT Any change or alteration of the vehicle might seriously affect its safety and road holding, thus causing accidents, in which the
occupants could even be fatally injured.
personal safety;
vehicle safety;
environmental protection.

IGNITION DEVICE
The key can be turned to three different
positions fig. 5:
❒ STOP: engine off, key can be removed,
steering column locked.
Some electrical devices (e.g. radio,
central door locking system, alarm, etc.)
are still available;
❒ MAR: driving position.
All electrical devices are available;
❒ AVV: engine starting.
The ignition device is fitted with a safety
system that requires the ignition key to
be turned back to STOP if the engine
does not start, before the starting
operation can be repeated.
2) 3)
5A0L0010
KNOWING YOUR CAR
10
KEY WITH REMOTE CONTROL
BATTERY REPLACEMENT
Procedure
1)
❒ press button 1 fig. 4 and move the
metal insert 2 to opening position; turn
screw 3 to :using a small point
screwdriver;
❒ remove battery compartment 4 and
replace battery 5, respecting the polarity;
reinsert compartment 4 in the key and
secure it by turning screw 3 to Á.
1)Press button 2 only with the key away
from your body, especially your eyes and
from objects which could get
damaged (e.g. your clothes). Do not leave
the key unattended to avoid the button
being accidentally pressed while it is
being handled, e.g. by a child.
IMPORTANT
1)Used batteries may be harmful to the
environment if not disposed of correctly.
They must be disposed of as specified by
law in the special containers or taken to
an Alfa Romeo Dealership, which will take
care of their disposal.
WARNING
1)The electronic components inside the
key may be damaged if the key is
subjected to strong shocks. In order to
ensure complete efficiency of the
electronic devices inside the key, it should
never be exposed to direct sunlight.
WARNING

DOORS
DOOR CENTRAL LOCKING/UNLOCKING
Locking from the outside
With the doors closed, press the Ábutton
on the key or turn the metal insert
(located inside the key) in the door lock.
LED 1 fig. 6 on the ≈button on the
dashboard will switch on to indicate that
the doors have locked.
Door locking is carried out with all doors
shut, irrespective of the tailgate
open/closed status.
6A0L0007
Door unlocking from the outside
Press the Ëbutton on the key or turn the
metal insert (located inside the key) in
the driver side door lock.
Door locking/unlocking from the inside
Press the ≈button. The button has an
LED that indicates whether the doors are
locked or unlocked.
LED on: doors locked.
LED off: doors unlocked.
EMERGENCY DOOR LOCKING
DEVICE
Passenger side door
The passenger side door is fitted with a
device to lock it when there is no power.
KNOWING YOUR CAR
12
DISARM ALARM
Press the Ëbutton.
IMPORTANT If the central door locking
system is released using the metal insert
of the key, the alarm is not disabled.
EXCLUDING THE ALARM
To completely disable the alarm (e.g.
during a lengthy period of car inactivity),
lock the car by turning the metal insert of
the key in the door lock.
VOLUMETRIC/ANTI-LIFT PROTECTION
To ensure the correct operation of the
protection, completely close the side
windows.
To disable the volumetric protection,
turn the ignition key from STOP to MAR
twice in a row, then activate the alarm
within 15 seconds, pressing the Ábutton
on the remote control.
To disable the anti-lift protection as well,
the ignition key must be turned from
STOP to MAR three times in a row,
followed by activating the alarm within
15 seconds, pressing the Ábutton on the
remote control.

23
ELECTRIC WINDOWS
These operate when the ignition key is
turned to MAR and for about three
minutes after the ignition key is turned to
STOP or removed unless one of the doors
is opened.
The buttons are located on the central
tunnel.
14)
CONTROLS
1 - opening/closing of left-hand window;
2 - opening/closing of right-hand
window.
Push the corresponding buttons to
open/close the desired window.
When one of the two buttons is pressed
briefly, the window moves in stages; if
the button is held down to open,
“continuous automatic” operation is
activated.
21A0L0002
If the button is pressed again the window
will stop in its current position. If the
button is pressed for several seconds,
the window lowers automatically (only
with ignition key in MAR position).
Automatic continuous operation (where provided)
This is activated by pressing one of the
two buttons for longer than half a
second. The window stops when it
reaches the end of travel position, or
when the button is pressed again.
It can be used on both the driver side and
passenger side, only for lowering the
window.
Electric window system initialisation
After there has been no power supply
for the control units (battery replaced or
disconnected or protective fuses for the
electric window control units replaced),
the automatic operation of the windows
must be restored.
The restoration procedure must be
performed as described below with the
doors closed:
❒ completely open the driver’s door
window keeping the operating button
pressed for at least three seconds after
the (lower) end of travel position;❒ completely raise the driver’s side
window and keep the button pressed for
at least three seconds once the end of
travel position (upper end stop) has been
reached;
❒ repeat stages 1 and 2 for the
passenger-side window;
❒ make sure that the initialisation is
correct by checking that the windows
work automatically.
14)Incorrect use of the electric windows
may be dangerous. Before and during
their operation, ensure that any
passengers are not at risk from the
moving glass either by personal objects
getting caught in the mechanism or by
being hit by it directly. When leaving the
car, always remove the key from the
ignition to prevent accidental operation
of the electric windows from being a
hazard for those still on board.
IMPORTANT

27
Alfa DNA SYSTEM
(Car dynamic control system)
This device allows, using lever 1 fig. 28
(on the central tunnel), four car response
modes to be selected according to
driving style and road conditions:
❒ d = Dynamicor Race
(sports driving mode);
❒ n = Natural(mode for driving in normal
conditions);
❒ a = All Weather(mode for driving in
poor grip conditions, such as rain and
snow).
28A0L0108
The lever 1 is a monostable, i.e. it always
remains in the central position.
The selected driving mode is indicated by
the corresponding LED switching on in
the panel and by an indication on the
display.
The device acts on the dynamic car
control systems (engine, steering, ESC,
ASR, ELECTRONIC Q2 systems, etc.).
“Natural” MODE
It is a manufacturer-recommended mode
aimed at comfort and safety in normal
grip and driving conditions.
“DYNAMIC“” MODE
IMPORTANT During the first 250 km of
car utilisation, the Dynamic and Race
modes are inhibited. Within this first
interval of start-up mileage it is advisable
to refrain from an aggressive driving
style, so that the best gear shifting
quality can be achieved over time.
Activation
Move lever 1 fig. 28 upwards (to the
letter “d”) and hold in this position for half
a second, until the corresponding LED
lights up and the “Dynamic” mode
activation indicator appears on the
display.
When released, lever 1 will return to
the central position.
Deactivation
To deactivate “Dynamic” mode and return
to “Natural”, move lever 1 fig. 28
downwards (to letter “a”) and keep it in
this position for half a second.
“Race” MODE
Activation
Move lever 1 fig. 28 upwards (to the
letter “d”) and hold in this position for 5
seconds, until the “Race” mode activation
indicator appears on the display.

KNOWING YOUR CAR
28
Deactivation
To deactivate “Race” mode and return to
“Dynamic”, move lever 1 fig. 28
downwards (to letter “a”) and keep it in
this position for half a second.
“ALL WEATHER”MODE
Activation
Move lever 1 fig. 28 downwards (to the
letter “a”) and hold in this position for half
a second, until the corresponding LED
lights up and the “All Weather” mode
activation indicator appears on the
display.
Deactivation
To deactivate “All Weather” mode and
return to “Natural”, move lever 1 fig. 28
upwards (to letter “d”) and keep it in this
position for half a second.

33
Some options have a submenu. The menu
can be activated by briefly pressing the
SET/
Nbutton.
The menu includes the following items:
❒ MENU
❒ SPEED BEEP
❒ TRIP B ACTIVATION/DATA
❒ SET TIME
❒ SET DATE
❒ AUTOCLOSE (where provided)
❒ UNIT OF MEASUREMENT
❒ LANGUAGE
❒ WARNING VOLUME
❒ BELT BUZZER/BEEP (may only be
displayed after the SBR system is
deactivated by a dedicated Alfa Romeo
Dealership)
❒ SERVICE
❒ AIRBAG/PASSENGER BAG
❒ DAYTIME RUNNING LIGHTS (where
provided)
❒ EXIT MENU
Selecting an option from the main
menu without a submenu:
❒ press the SET/Nbutton briefly to
select the main menu setting you wish to
change;
❒ press buttons or (with single
presses) to select the new setting;
❒ press the SET/
Nbutton briefly to
save the new setting and go back to the
previous main menu option.
Selecting an option from the main
menu with a submenu:
❒ briefly press the
SET/
Nbutton briefly to see the first
submenu option;
❒ press buttons or (single presses)
to scroll all options in the submenu;
❒ briefly press the
SET/
Nbutton to select the option of
the displayed submenu to access the
respective submenu;
❒ press the buttons or (with single
presses) to select the new setting for the
specific submenu option;
❒ briefly press the SET/
Nbutton to
store the setting and go back to the same
item of the previously selected menu
at the same time.
TRIP COMPUTER
The Trip computer is used to display
information on car operation when the
key is turned to MAR.
This function is characterised by two
separate records, called “Trip A” and
“Trip B”, where the car’s “complete
missions” (journeys) are recorded in a
reciprocally independent manner.
Both memories can be reset: i.e. start of a
new journey.
“Trip A” can be used to display the values
relating to:
❒ Range
❒ Distance travelled
❒ Average consumption
❒ Instantaneous consumption
❒ Average speed
❒ Trip time (driving time).
“Trip B” may be used to display the
figures relating to:
❒ Distance travelled B
❒ Average consumption B
❒ Average speed B
❒ Trip time (driving time).
The “Trip B” function may be excluded.
“Range” and “Instant consumption” values
cannot be reset.

KNOWING THE INSTRUMENT PANEL TOOLS
38
Warning lights on panelMeaningWhat to do
In any situation in which the message is “See manual”, it is
ESSENTIAL to refer to the contents of the “Wheels”
paragraph in the “Technical data” chapter, strictly
complying with the indications that you find there.
Low tyre pressure - See manual
The warning light switches on, together with a dedicated
message on the display, to indicate that the tyre pressure
is lower than the recommended value and/or that slow
pressure loss is occurring. In these circumstances, optimal
tyre duration and fuel consumption may not be
guaranteed.
Should two or more tyres be in the condition mentioned
above, the display will show the indications corresponding
to each tyre in sequence.
Contact a dedicated Alfa Romeo Dealership as soon as
possible. TPMS system fault
The warning light switches on when a fault is detected in
the TPMS.
Should one or more wheels be fitted without sensors, the
display will show a warning message until initial conditions
are restored.IMPORTANT Do not continue driving with one or more flat
tyres as handling may be compromised. Stop the vehicle,
avoiding sharp braking and steering. Repair immediately
using the dedicated kit (see “Repairing a wheel” paragraph
in the “In an emergency” chapter) and contact the
dedicated Alfa Romeo Dealership as soon as possible. TPMS SYSTEM

45
Warning lights on panelMeaningWhat to do
EXTERIOR LIGHTS FAILURE
The symbol and corresponding message appear on the
display if a fault is detected in one of the following lights:
❒ daytime running lights (DRLs)
❒ side lights
❒ dipped beam headlights
❒ direction indicators
❒ rear fog lights
❒ reversing lights
❒ number plate lights.
The failure relating to these lights could be: one or more
blown bulbs, a blown protection fuse or a break in the
electrical connection.
Check and replace the concerned fuses as shown in the
“If a fuse blows” paragraph in the “In an emergency”
chapter; if this does not solve the fault, check and replace
the concerned bulbs as described in “Replacing an exterior
bulb” in the “In an emergency” chapter.
Should this operation also fail to resolve the fault, contact
the dedicated Alfa Romeo Dealership, for a
comprehensive check of the electrical system.
SERVICE (SCHEDULED SERVICING)
The digital warning light appears automatically, together
with an associated message, with the key at MAR, starting
from 2,000 km (or equivalent distance in miles) from the
next scheduled servicing operation and shown again every
200 km (or equivalent distance in miles).Contact a dedicated Alfa Romeo Dealership.
The operations of the “Scheduled Servicing Plan” will be
performed and the message will be reset.