ECO mode Alfa Romeo Giulietta 2012 Owner handbook (in English)

Dear Customer,
Congratulations on your purchase and thank you for choosing Alfa Romeo.
We have written this handbook to help you get the most out of your new car.
Please read it all the way through before taking your car on the road for the first time.
Here you will find information, tips and important warnings regarding use of your car and how to achieve the best performance from
the technological features of your Alfa Romeo.
The booklet also provides a description of special features as well as tips and essential information for the correct care and mainte-
nance of your Alfa Romeo and safe driving tips.
Please read the warnings and indications at the bottom; these are marked with the following symbols:
personal safety
car’s wellbeing
environmental protection.
The enclosed Warranty Booklet lists the services that Alfa Romeo offers to its Customers:
– the Warranty Certificate with terms and conditions for maintaining its validity
– the range of additional services available to Alfa Romeo Customers.
We are confident that these instructions will help you become familiar with your new car and the Alfa Romeo after-sales staff who will
be at your service.
Enjoy the read. Happy motoring!
This Owner Handbook describes all versions of Alfa Giulietta; please consider only the information
relevant to your version, engine and configuration.
The data in this publication is provided by way of example. Fiat Group Automobiles can modify
the specifications of the model described in this publication at any time, for technical or marketing
purposes. For further information, contact an Alfa Romeo Authorised Service Provider.

11
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Hot engine coolant (red)
When the ignition key is turned to MAR, the warning
light turns on but should go off after a few seconds.
The warning light turns on when the engine is over-
heated. A specific message will be shown on the display.
If the warning light comes on, proceed as follows:
❍when driving normally: stop the car, switch off the engine and
check that the water level in the reservoir is not below the MIN
mark. If it is not, wait for a few minutes for the engine to cool
down then slowly and carefully open the cap, top-up with coolant
and check that the level is between the MIN and MAX marks.
Also visually check for leaks. If the warning light comes on again
at the next engine start-up, contact Alfa Romeo Authorized Ser-
vices.
❍if the car is used under demanding conditions (e.g. towing trail-
ers uphill or fully loaded): slow down and, if the light stays on,
stop the car. Stop for two or three minutes with the engine run-
ning and slightly accelerated to assist better coolant circulation.
Then switch the engine off. Check correct fluid level as described
above.
IMPORTANT On particularly demanding journeys, it is advisable to
keep the engine on and slightly accelerated for a few minutes be-
fore switching it off.
u
Door open (red)
(for versions/markets, where provided)
The warning light (or symbol on the display) comes
on when one or more doors or the boot are not perfectly
closed. An acoustic signal is activated with the doors open and
the car moving. On some versions, the warning light (or symbol
on the display) also lights up when the bonnet is not perfectly
closed.´
EOBD/injection system fault (amber)
Under normal conditions, the warning light comes on
when the ignition key is turned to MAR, but should
go off as soon as the engine is started.
If the warning light remains on or comes on whilst driving, that
means that the injection system is not working properly; in partic-
ular, if the warning light comes on constantly, this indicates a mal-
function in the supply/ignition system that could cause excessive
exhaust emissions, a possible loss of performance, poor driveabil-
ity and high fuel consumption.
A specific message is displayed on certain versions.
Under these conditions, you can continue travelling at moderate
speed without demanding excessive effort from the engine. Pro-
longed use of the car with the warning light on may cause dam-
age. Contact Alfa Romeo Authorized Services as soon as possible.
The warning light goes out after the fault disappears, but the in-
dication is stored in the system.U

12
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
VDC system (amber)
(for versions/markets, where provided)
When the ignition key is turned to MAR, the warning
light turns on but should go off after a few seconds. If
the warning light does not go out, or if it remains lit up when dri-
ving, contact Alfa Romeo Authorized Services. A specific message
is displayed on certain versions. The warning light will flash while
driving to indicate that the VDC system is intervening.
ASR fault
When the ignition key is turned to MAR, the warning light turns
on but should go off after a few seconds. If the warning light does
not go out, or if it remains lit up when driving, contact Alfa Romeo
Authorized Services. A specific message is displayed on certain ver-
sions. The warning light will flash while driving to indicate that
the ASR system is intervening.
Hill Holder fault
This warning light comes on, on some versions together with the
*symbol and a message in the display, in the event of a Hill Hold-
er system fault. In this case, contact your nearest Alfa Romeo Au-
thorized Services.
á
NOTE (petrol engines only)
If the warning light is flashing, this indicates that the catalytic
converter may be damaged.
If the warning light comes on intermittently, release the accelera-
tor pedal to lower the speed of the engine until the warning light
stops flashing; continue the journey at moderate speed, trying to
avoid driving conditions that may cause further flashing and contact
an Alfa Romeo Authorised Service Provider as soon as possible.
Contact Alfa Romeo Authorized Services as soon as
possible if the
Uwarning light does not light up
or if, while travelling, the warning light comes on
either fixed or blinking (in combination with a message
on the display on some versions). The operation of the
U
warning light may be checked by traffic police using ap-
propriate equipment. Follow the laws in force in the coun-
try where you are driving.

19
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Rain sensor fault
(for versions/markets where provided)
On some versions, a message + symbol will be shown
on the display if a dusk sensor fault is detected. 1
Parking sensor fault
(for versions/markets where provided)
On some versions, a message + symbol will be shown
on the display if a parking sensor fault is detected.
Rain sensor fault
(for versions/markets where provided)
On some versions, a message + symbol will appear on
the display if a rain sensor fault is detected. u
t
Brake lights fault
On some versions, a message + symbol will appear on
the display if a brake light fault is detected. The fault may be caused
by a blown bulb, a blown protection fuse or an interruption of the
electric connection.TDrive mode display (“Alfa DNA” system)
(for versions/markets, where provided)
On versions equipped with a reconfigurable multifunction display,
a message + symbol associated with the selected driving mode -
“DYNAMIC”, “NORMAL” or “ALL WEATHER” - is shown. A warn-
ing message is shown on the display if one of these driving modes
is not available.
On versions equipped with multifunction display, a letter (d or a)
associated with the selected driving mode is shown together with
a dedicated message.

20
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
DISPLAY
The car may be equipped with a multifunction display/ multi-
function reconfigurable display which, in accordance with the set-
tings made, can display useful information when driving.
With the ignition key removed, the display lights up and shows the
time and total odometer reading (in km or miles) for a few sec-
onds when a door is opened/closed.
MULTIFUNCTION DISPLAY “STANDARD”
SCREEN fig. 6
The following information is shown on the display:
A. Date
B. Odometer (distance covered in km or miles)
C. Driving mode selected using “Alfa DNA” (dynamic control sys-
tem) (for versions/markets, where provided)
– d = Dynamic
– n = Normal
– a = All Weather
D. Time (always displayed, even with the key extracted and the
front doors closed)
E Start&Stop function indicator (for versions/markets, where
provided)
F. Outside temperature
G Gear Shift Indicator (for versions/markets where provided)
H. Headlight alignment position (dipped headlamps on only)
fig. 6A0K1222g

21
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
RECONFIGURABLE MULTIFUNCTION
“STANDARD” DISPLAY fig. 7
The following information is shown on the display:
A. Time
B. Trip meter (km or miles)
C. Odometer (display of distance travelled in kilometres/miles)
D. State indicator (e.g. doors open, ice on road, etc.)/Start&Stop
function indicator (for versions/markets, where provided)/
Gear Shift Indicator (for versions/markets, where provided)
E. Headlamp alignment position (only with dipped headlamps
on).
F. Outside temperatureThe turbocharger pressure will appear on some versions when
“DYNAMIC” driving mode is selected (see “Alfa DNA system” in
this chapter), fig. 8.
fig. 7A0K0005mfig. 8A0K0006m

47
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
ALARM(for versions/markets, where provided)
OPERATION OF THE ALARM
The alarm intervenes in the following instances:
❍unauthorised opening of doors/bonnet/boot (perimeter pro-
tection);
❍unauthorised operation of ignition system (ignition key rotat-
ed to MAR);
❍the battery cables cutting;
❍when someone is moving inside the passenger compartment
(volumetric protection);
❍anomalous lifting/tilting of the vehicle (for versions/markets,
where provided).
Operation of the alarm is indicated by an acoustic and visual sig-
nal (flashing of the direction indicators for several seconds). The
alarm triggering modes may vary according to the markets. There
is a maximum number of acoustic/visual cycles. When this is
reached the system returns to normal operation.
IMPORTANT The engine locking function is guaranteed by the Alfa
Romeo CODE, which is automatically activated when the ignition
key is extracted from the ignition switch.
IMPORTANT The alarm is configured to comply with the regulations
existing in different countries.
SWITCHING ON THE ALARM
With the doors and bonnet closed and the ignition key either turned
to STOP or removed, direct the key with the remote control to-
wards the car, then press and release
Ábutton. Except specific
markets, the system produces a visual and acoustic signal and
enables door locking.
A self-diagnostic stage precedes the turning on of the alarm: In case
of faults the system will generate a further acoustic and/or visu-
al signal using the LED on the dashboard.
If after the alarm is switched on, a second acoustic signal is emit-
ted and/or the LED on the dashboard flashes, wait about 4 sec-
onds and switch off the alarm by pressing
Ëbutton, check that the
doors, bonnet and boot are closed correctly and then reactivate the
system by pressing
Ábutton.
If the alarm produces an acoustic signal even when the doors, bon-
net and boot are correctly closed, a fault has occurred in system
operation: in this case, go to Alfa Romeo Authorized Services.
ALARM SELF-ACTIVATION
(for versions/markets, where provided)
If the alarm has not been activated using the remote control, once
about 30 seconds have elapsed from when the ignition key was
turned to STOP and a door or the tailgate was last opened and
then closed, the alarm activates automatically. This is indicated
by the LED on the button A-fig. 20 lighting up intermittently and
the indications of activation described previously.
To deactivate the alarm, press the
Ëbutton on the remote control.
The alarm also activates when the doors are closed by turning
the metal insert of the key in the driver side door latch. If the sys-
tem self-activates, the doors are not locked.

75
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
MAIN BEAM HEADLIGHTS
With A ring in position 2pull the stalk towards the steering wheel
(stable position). The warning light
1on the instrument panel
will come on. To turn the lights off, pull the stalk again towards
the steering wheel (dipped beam headlights will stay on). It is
not possible to switch on the main beam headlights in fixed mode
if the automatic lighting control system is active.
FLASHINGS
Pull the stalk towards the steering wheel (unstable position) re-
gardless of the position of A ring. The
1warning light will come
on in the instrument panel.
DIRECTION INDICATORS
Put the stalk in the stable position:
❍upward: activation of right direction indicator;
❍downward: activation of left direction indicator.
Lights
¥orÎwill flash on the instrument panel. The direction in-
dicators are switched off automatically when the steering wheel
is straightened.
“Lane change” function
If you want to signal that you are changing lane, hold the left stalk
in the unstable position for less than half a second. The direction
indicator on the selected side flashes five times and then switch-
es off automatically. IMPORTANT The sensor is unable to detect the presence of fog. Un-
der these circumstances, these lights are therefore turned on man-
ually.
When the lights are turned on by the sensor, the fog lights (for ver-
sions/markets, where provided) and the rear fog lights may be
turned on. When the lights are automatically switched off, the front
and rear fog lights (if activated) are also switched off. The next
time the lights are switched on automatically, the fog lights must
be reactivated manually (if required).
With the sensor active, it is possible to flash the headlights but
the main beam headlights cannot be switched on. If you need to
turn these lights on, turn A ring fig. 40 to position
2and turn
the dipped beam headlights on.
When the lights have been activated automatically and are then
switched off by the sensor, the dipped beam headlights are switched
off first, followed by the side lights a few seconds later.
If the sensor is activated but is malfunctioning, the side lights and
dipped beam headlights are switched on independently of the out-
side light level and the sensor fault is indicated on the instrument
panel display. It is also possible to deactivate the sensor and switch
on these light.

79
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
CRUISE CONTROL
(for versions/markets, where provided)
GENERAL INFORMATION
This is an electronic driving aid that allows you to drive at a speed
of above 30 km/h on long and straight dry roads (e.g. motor-
ways), at a preset speed without having to press the accelerator
pedal. It is therefore not recommended to use this device on coun-
try roads with traffic. Do not use it in town.
TURNING THE DEVICE ON
Turn ring A-fig. 43 to ON. The device cannot be turned on in 1stor
reverse gear. It is advisable to engage it in 5thgear or higher.
When travelling downhill with the device engaged, the car may
slightly exceed the preset speed. When the device is activated,
Ü
light comes on together with the relevant message on the instru-
ment panel (for versions/markets, where provided).
REAR WINDOW WIPER/WASHER
(for versions/markets, where provided)
Activation
This only operates with the ignition turned to MAR.
Turn B ring fig. 41 from position
Oto position 'to turn on the
rear window wiper as follows:
❍intermittent operation if the windscreen wiper is off;
❍synchronised operation (but with half-stroke frequency) when
the windscreen wiper is on;
❍continuous operation with reverse engaged and windscreen
wiper on.
With reverse gear engaged and windscreen wiper on, the rear win-
dow wiper is activated in continuous mode. Pushing the stalk to-
wards the dashboard (temporary position) the rear window wash-
er jet will activate.
Keeping the stalk pushed for more than half a second also the rear
window wiper will activate. Releasing the stalk will activate the
smart washing function, as described for the windscreen wiper.
fig. 43A0K0098m

82
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
B switch operates the map reading light.
B switch positions:
❍central position (position 1): C and D lights are always off;
❍pressed to the left (position 0): C light on;
❍pressed to the right (position 2): D light on.
IMPORTANT Before getting out of the car, make sure that both
switches are in the central position: closing the doors the lights will
go out avoiding to drain the battery.
In any case, if the switch is left inadvertently in the On position,
the ceiling lights will turn off automatically 15 minutes after turn-
ing the engine off.
CEILING LIGHT TIMING
On certain versions, two different timed switching-on modes have
been provided to facilitate getting in/out of the car at night or with
poor lighting.
Timing while getting into the car
The ceiling lights switch on according to the following modes:
❍for about 10 seconds when the front doors are unlocked;
❍for about 3 minutes when one of the doors is opened;
❍for about 10 seconds when the doors are closed.
The timing is interrupted when the ignition is turned to MAR.
Timing while getting out of the car
After removing the key from the ignition switch, the courtesy lights
will turn on as follows:
❍within 2 minutes from turning the engine off for about 10
seconds;
❍for about 3 minutes when one of the doors is opened;
❍when one of the doors is closed for about 10 seconds.
Timing will stop automatically when locking the doors.