service interval Alfa Romeo GT 2005 Owner handbook (in English)

GETTING TO KNOW YOUR CAR
12
– if the led continues flashing, but at dif-
ferent intervals than normal, this means
that different attempts to break in have
occurred. Through the number of flashes it
is possible to identify the type of attempt:
1 flash:one or more doors
2 flashes:tailgate
3 flashes:bonnet
4 flashes:ultrasounds
5 flashes:abnormal vehicle lift-
ing/sloping (for ver-
sions/markets where
applicable)
6 flashes:tampering with car start-
ing cables
7 flashes:tampering with battery
cables or cutting emer-
gency key cables
8 flashes:connection line to sen-
sors and siren
9 flashes:at least three causes of
alarm. Surveillance
After switching on, the flashing of the
deterrent led (A-fig. 7) on the dash-
board indicates the system surveillance
mode. The led flashes throughout this
period.
IMPORTANTOperation of the elec-
tronic alarm is adapted at the origin to the
rules of the different countries.
Self-diagnostic functions
and door, bonnet, boot control
If, after engaging the alarm, a second
“beep” is sounded, switch off the system
pressing the button (B-fig. 6), check
that the doors, bonnet and tailgate are
properly shut, then switch the system on
again pressing the button (C). Otherwise,
the door, bonnet or tailgate that is not
shut properly will be excluded from the
alarm system control.
If the doors, bonnet and boot are shut
correctly and the control signal is repeat-
ed, the system self-diagnostic has detect-
ed a system operating fault. It is therefore
necessary to contact Alfa Romeo
Authorised Services.HOW TO DEACTIVATE
THE ALARM
To deactivate the alarm press the button
(B-fig. 6) of the key with remote control.
The system will react as follows (with the
exception of certain markets):
– two brief flashes of the direction indi-
cators
– two brief “beeps” of the system
– door unlocking.
IMPORTANTIf when the system is
turned off the deterrent led (A-fig. 7)
on the dashboard stays on (maximum 2
minutes or until the ignition key is set to
MAR) the following should be borne in
mind:

GETTING TO KNOW YOUR CAR
107
HEATING (fig. 98)
To obtain the temperature required, pro-
ceed as follows:
- temperature adjustment knob pointer (1)
on the red sector as required;
- air quantity adjustment knob pointer (2)
on the fan speed required to personalise the
amount of air admitted;
- air distribution knob pointer (3) on the
required position.
To obtain the maximum heating power pro-
ceed as follows:
- knob pointer (1) as far as it will go clock-
wise (maximum temperature red sector);
- knob pointer (2) on maximum fan
speed;
- air distribution knob pointer (3) on the
required position (position
w) is recom-
mended.
IMPORTANTTo be able to obtain sat-
isfactory passenger compartment warming,
the engine should have reached normal op-
erating temperature.The filter has the specific capability of com-
bining the mechanical filtering of the air with
an electrostatic effect so that the outside air
admitted to the passenger compartment is
purified and free of particles such as dust,
pollen, etc.
In addition to the above mentioned func-
tions, is also reduces the concentration of
pollutants.
The filtering action is active in all air inlet
conditions and it is clearly more effective
with the windows closed.
Have the conditions of the filter checked
at least once a year, preferably at the on-
set of summer by Alfa Romeo Authorised
Services.If the car is habitually used in dusty or pol-
luted areas, the filter should be checked and
replaced at shorter intervals than those spec-
ified in the Programmed Maintenance
Schedule.
If the filter is not replaced
the efficiency of the cli-
mate control system may
be seriously compromised up to
blocking the air flow at the outlets
and vents.
POLLEN FILTER
(for versions/markets where applicable)
A0A0734b
fig. 98

GETTING TO KNOW YOUR CAR
122
WING MIRROR AND
REARSCREEN
DEFROSTING/DEMISTING
BUTTON
(fig. 113)
Pressing button (9)
(turns on demist-
ing/defrosting of the rearscreen and, if pre-
sent, the wing mirror coils.
The turning on of this function is shown by
the turning on of the led on the button.
This function is timed and switches off au-
tomatically after 20 minutes, or pressing the
button again; the function is also switched
off when the engine is stopped and will not
be switched on again the next time the en-
gine is started.
IMPORTANTThe system automatically
turns on rearscreen heating if the tempera-
ture is below 3
°C.
IMPORTANTDo not apply stickers on
the inside of the rearscreen over the heat-
ing filaments to avoid damage that might
cause it to stop working properly.
POLLEN FILTER
Have the conditions of the filter checked
by Alfa Romeo Authorised Services at least
once a year, preferably at the onset of sum-
mer.
If the vehicle is used mainly in dusty or pol-
luted areas it should be checked and, if nec-
essary, replaced at shorter intervals.
A0A0214b
The filter has the specific capability of com-
bining the mechanical filtering of the air with
an electrostatic effect so that the outside air
admitted to the passenger compartment is
purified and free of particles such as dust,
pollen, etc.
In addition to the above mentioned func-
tion, it also reduces the concentration of pol-
lutants.
The filtering action takes place under all
air inlet conditions and it is clearly most ef-
fective with the windows shut.The failure to replace the
filter may considerably re-
duce the effectiveness of
the climate control system up to
blocking the air flow from the out-
lets and vents.
fig. 113

Never leave children
unattended in the vehicle.
Always remove the igni-
tion key when leaving the vehicle
and take it with you.To avoid useless con-
sumption of power and
possible draining of the
battery, never leave the ignition
key in the MAR position when
the engine is not running.
CORRECT USE OF THE CAR
203
PARKING
When the vehicle is parked, proceed as
follows:
– Switch off the engine.
– Engage the handbrake.
– Engage first gear if the vehicle is faced
uphill or reverse if the vehicle is facing
downhill.
– Turn the front wheels so that the vehi-
cle will immediately come to a halt if the
handbrake slips.
REDUCING RUNNING
COSTS AND
ENVIRONMENT
POLLUTION
By following a few simple guidelines, it
is possible to save vehicle running costs
and reduce harmful emissions.
GENERAL CONSIDERATIONS
Vehicle maintenance
To take care of the car maintenance
have the checks and adjustments carried
out in accordance with the “Scheduled
Maintenance Programme”.
Tyres
Check the pressure of the tyres routinely
at an interval of no more than 4 weeks: if
the pressure is too low consumption levels
increase as resistance to rolling is higher.
Useless loads
Never travel with an overload in the
boot. The weight of the vehicle (especial-
ly in urban traffic), and its geometry heav-
ily affect consumption levels and stability.Electric services
Use electric devices only for the amount
of time needed. Rearscreen heating, addi-
tional headlights, windscreen wipers and
heater fan need a considerable amount of
energy, therefore increasing the require-
ment of current increases fuel consump-
tion (up to +25% in the urban cycle).
Climate control system
The climate control system is a further
load bearing heavily on the engine induc-
ing higher consumption levels(up to
+20% on average). Outside temperature
permitting, preferably use the air vents.
Aerodynamic items
The use of non-certified aerodynamic
items may adversely affect air drag and
consumption levels.

VEHICLE MAINTENANCE
251
IMPORTANT
Engine oil
Should prevailing use of the car be under
one of the following specially heavy con-
ditions:
– trailer or caravan towing
– dusty roads
– short distances (less than 7-8 km)
repeated and with external temperatures
below zero
– frequently idling engines or long dis-
tance low speed driving or in case of a
long term inactivity
replace engine oil more frequently than
required on Service Schedule.IMPORTANT
Diesel filter
The different grades of purity in diesel
fuel normally available might make it nec-
essary to replace the filter more frequent-
ly than indicated in the Service Schedule.
If the engine misfires it shows the filter
needs changing.IMPORTANT
Air cleaner
Using the car on dusty roads change the
air cleaner more frequently than specified
in the Schedule Maintenance Programme.
For any doubts concerning the intervals
between the engine oil and air cleaner
replacement in relation to how the vehicle
is used, contact Alfa Romeo Authorised
Services.

VEHICLE MAINTENANCE
255
ENGINE OIL (fig. 4-4a-5-6)
The engine oil should be checked with
the vehicle on a level surface a few min-
utes (about 5) after the engine has been
switched off.
Remove the dipstick (A), clean it, put it
back in completely, remove it and check
that the level is within the MINand
MAXmarks on the dipstick. The interval
between the MINandMAXmarks cor-
respond to about one litre of oil.When the engine is hot,
take care when working
inside the engine com-
partment to avoid burns.
Remember that when the engine
is hot, the fan may cut in: danger
of injury.
Do not add oil with spec-
ifications (classification,
viscosity) other than
those of the oil already in the
engine.
fig. 4 - 1.8 T. SPARK version
A0A0737b
fig. 6 - JTD 16Vversion
A0A0398b
AB
fig. 5 - 3.2 V6version
A0A0406b
If the oil level is near or even below the
MINmark, add oil through the filter neck
(B), until reaching the MAXmark.
IMPORTANTIf a routine check
reveals that the level is above the MAX
mark, contact Alfa Romeo Authorised
Services to have the correct level restored.
IMPORTANTAfter topping up the oil,
before checking the level again, run the
engine a few seconds and wait for a few
minutes ater stopping it.
fig. 4a - 2.0 JTS version
A0A0682b

VEHICLE MAINTENANCE
260
DIESEL FUEL FILTER
(JTD16Vversions)
DRAINING CONDENSATION
WATER
The presence of water in
the supply circuit may
cause serious damage to
the entire injection system and
cause irregular running of the
engine. If the
cwarning light
turns on together with the mes-
sage on the reconfigurable multi-
function display, contact Alfa
Romeo Authorised Services as
soon as possible to have the sys-
tem relieved.
AIR CLEANER
The air cleaner is connected to the tem-
perature and air flow sensors which send
to the control unit the electric signals
needed for correct operation of the injec-
tion and ignition system.
It must therefore always be in perfect
conditions, to ensure correct operation of
the engine, low consumption and exhaust
emission levels.
If the operations con-
cerning cleaner replace-
ment described below are
not carried out correctly and with
the due precautions, they may
compromise the travelling safety
of the vehicle. You are recom-
mended to have this operation
carried out by Alfa Romeo
Authorised Services.
If the car is habitually
used in dusty areas, the
cleaner should be replaced
at shorter intervals than those
specified in the Programmed
Maintenance Schedule.
Any attempt to clean the
cleaner may damage it,
leading to serious engine
damage.

VEHICLE MAINTENANCE
261
BATTERY
The battery is of the “Limited
Maintenance” type and is fitted with an
optical indicator (A-fig. 12) for check-
ing the electrolyte level and charge.
Under normal conditions of use the elec-
trolyte does not need topping up with dis-
tilled water. To make sure that it is in effi-
cient conditions, at routine intervals check
the indicator on the battery cover which
should be dark in colour with a green cen-
tral area.
If the indicator is a bright light colour, or
dark without the green central area, con-
tact Alfa Romeo Authorised Services.
fig. 12
A0A0224b
Batteries contain harmful
substances for the envi-
ronment. To change the
battery we advise contacting Alfa
Romeo Authorised Services who
are equipped for disposal respect-
ing nature and the law.
The incorrect installation
of electric accessories
may cause serious dam-
age to the vehicle. If, after buy-
ing the car, you wish to install
accessories (alarm, radio,
radiotelephone, etc.) contact Alfa
Romeo Authorised Services who
will be able to suggest the most
suitable devices and above all
advise about the need to use a
more powerful battery.
If the car is to remain
inactive for a long time in
very cold conditions,
remove the battery and take it to
a warm place, otherwise it may
freeze.
POLLEN FILTER
Have the dust/pollen filter checked once
a year by Alfa Romeo Authorised Services,
preferably at the onset of summer.
If the car is mainly used in dusty or heav-
ily polluted areas, the filter should be
changed at more frequent intervals than
specified in the Scheduled Maintenance
Programme.
IMPORTANTThe failure to replace
the pollen filter can considerably reduce
the effectiveness of the climate control
system.
When working on the
battery or near to it,
always protect the eyes
with goggles.
The liquid contained in
the battery is poisonous
and corrosive. Avoid con-
tact with the skin or eyes. The
battery should be charged in a
well ventilated place away from
naked flames or possible sources
of sparks: danger of explosion
and fire.

VEHICLE MAINTENANCE
263
2.close the driver's window completely
keepingthe button pressedfor at
least 3 seconds after window closing (win-
dow upper stop);
3.repeat the same procedure (point 1
and 2) also for the front passenger's win-
dow;
4.check for proper initialisation by oper-
ating the windows automatically.
USEFUL HINTS TO EXTEND
THE LIFE OF YOUR BATTERY
To avoid rapidly draining the battery and
ensure that it continues to work correctly,
the following should be noted:
– The terminals must always be firmly
tightened.
– Within reason, avoid using electrical de-
vices for a long time when the engine is
switched off (radio, hazard warning lights,
parking lights, etc.). IMPORTANTIf the battery is kept
with a charge of below 50% it is damaged
by sulphation, its starting capability is
reduced and it is also more subject to the
possibility of freezing (this may occur
already at -10 °C). In the event of a pro-
longed inactivity, refer to the paragraph
“Vehicle inactivity”, in the chapter
“Correct use of the car”.
CHANGING THE BATTERY
When changing the battery it should be
replaced with another original one with
the same characteristics. If it is replaced
by a battery with different characteristics,
the maintenance intervals given in the
Scheduled Maintenance Programme in
this chapter are no longer valid and for
maintenance it will be necessary to follow
the battery Manufacturer’s instructions.
IMPORTANTAfter control unit power
disconnection (battery replacement or dis-
connection and replacement of power win-
dow control unit protection fuses), the
power window automatism shall be
restored.
Proceed as follows with doors closed:
1.open the driver's window completely
keepingthe button pressedfor at
least 3 seconds after window opening
(window lower stop);– When the vehicle is parked in a garage,
ensure that the doors, bonnet, boot and in-
ner lids are closed properly so that the lights
do not stay on permanently.
– Before carrying out any work on the
electric system, disconnect the negative ca-
ble from the battery.
– If after buying the car, you wish to in-
stall electric accessories which require a per-
manent electric supply (alarm, voice feature,
radionavigator with satellite antitheft func-
tion etc.) or accessories that burden the elec-
tric system, contact Alfa Romeo Authorised
Services whose qualified personnel, in ad-
dition to suggesting the most suitable de-
vices belonging to Lineaccessori Alfa Romeo,
will evaluate the overall electric absorption,
checking whether the vehicle’s electric sys-
tem is capable of withstanding the load re-
quired, or whether it should be integrated
with a more powerful battery. In fact, as
some of these devices continue absorbing
energy even when the ignition key is off (car
stationary, engine off), they gradually drain
the battery.

TECHNICAL SPECIFICATIONS
284
Use Fluid and lubricant specifications Genuine fluids Change
for correct car operation and lubricants intervals
Lubricants for
petrol engines
1.8 T.SPARK
Lubricants for
petrol engines
2.0 JTS - 3.2 V6
Lubricants for
Multijet engines
FLUIDS AND LUBRICANTS
RECOMMENDED PRODUCTS AND THEIR SPECIFICATIONS
Synthetic-based engine oils, grade SAE 10W-40,
FIAT 9.55535-G2qualification
Synthetic-based engine oils, grade SAE 10W-60,
FIAT 9.55535-H3qualification
Synthetic-based engine oils, grade SAE 5W-40,
FIAT 9.55535-M2qualification
Should non-genuine products be used, lubricants with minimum ACEA A3 properties for petrol engines and ACEA B4 for Diesel engines are tolerated; in this
event top engine performance is not guaranteed.
Using low-quality products, not compliant with ACEA A3 and ACEA B4 properties could cause engine damages not covered by warranty.
For very cold temperatures, consult Alfa Romeo Authorized Services for the proper Seleniaproduct to use
SELENIA 20K
ALFA ROMEO
SELENIA RACING
SELENIA WRAs per Service Schedule
As per Service Schedule
As per Service Schedule