clock setting ACURA NSX 1991 Service Repair Manual

II. ENGINE CONTROL MODULE (ECM) Reset Procedure

1. Turn the ignition switch off.

2. Remove the CLOCK (7.5 A) fuse from the under-hood fuse/relay box for 10 seconds to reset ECM.

NOTE: Disconnecting the CLOCK fuse also cancels the radio preset stations and the clock setting. Make note of

the radio presets before removing the fuse so you can reset them.

III. Final Procedure (this procedure must be done after any troubleshooting)

1. Remove the Jumper Wire.

NOTE: If the Service Check Connector is jumped, the MIL will stay on.

2. Do the ECM Reset Procedure.

3. Set the radio preset stations and the clock setting.

(cont'd)
CLOCK

(7.5 A) FUSE

UNDER-HOOD

FUSE/RELAY BOXProCarManuals.com

Idle Control System
Idle Speed Setting
Inspection/Adjustment NOTE: (Canada) Pull the parking brake lever up.
Start the engine, then check that the head lights

are
off.
1. Start the engine and warm it up to normal operating temperature (the cooling fan comes on).
2. Connect a tachometer. Connect a tachometer to loop of ICM second-
ary, or...
TACHOMETER

ICM

Remove the rubber cap from the tachometer
connector and connect a tachometer.
TACHOMETER
TACHOMETER CONNECTOR
RUBBER

CAP
3. Disconnect the 2P connector from the IAC valve.
IAC VALVE
4. Start the engine with the accelerator pedal slightly depressed, then turn the headlights and rear defog-
ger ON. After the MIL comes on, stabilize the

engine speed at 1000 rpm, then slowly release the

pedal until the engine idles.

If the engine stalls, turn the idle adjusting screw
one turn counterclockwise and recheck.
5. Check idling with the headlights and rear defogger
on.

Idle speed should be:
M/T
A/T
550 ± 50 rpm
550 ± 50 rpm (in or range)
Adjust the idle speed, if necessary, by turning
the idle adjusting screw.
If the proper idle speed cannot be achieved,
clean the throttle body port with carburetor
cleaner.

IDLE ADJUSTING

SCREWProCarManuals.com

Troubleshooting Procedures

When the Transmission Control Module (TCM) senses an abnormality in the input or output systems, the indicator
light in the gauge assembly will blink. However, when the Service Check Connector (located to the lower right of the glove compartment) is connected with a jumper wire, the indicator light will blink the Diagnostic Trouble Code (DTC)

when the ignition switch is turned on.

When the indicator light has been reported on, connect the two terminals of the Service Check Connector together.
Then turn on the ignition switch and observe the indicator light.
Codes 1 through 9 are indicated by individual short blinks. Codes 10 through 16 are indicated by a series of long and
short blinks. One long blink equals 10 short blinks. Add the long and short blinks together to determine the code. After
determining the code, refer to the electrical system Symptom-to-Component Chart on page 14-52 and 53. SERVICE CHECK
CONNECTOR
Connect with jumper wire.

INDICATOR
Some PGM-FI problems will also make the indicator light come on After repairing the PGM-FI system, disconnect the
CLOCK fuse (7.5 A) in the main relay box for more than 10 seconds to reset the TCM memory.
long short
See DTC 1

See DTC 2

See DTC 14

LIGHT

short
PGM-FI system
The PGM-FI system on this model is a sequential multiport fuel injection system. Disconnecting the CLOCK fuse also cancels the radio preset stations and the clock setting. Make note of the radio
presets before removing the fuse so you can reset them.

NOTE:ProCarManuals.com

If the inspection for a particular DTC requires the use of Test Harness (07LAJ—PT3010A):
Connect the wire harness to the Test Harness, and/or connect the Test Harness to the TCM according to the

troubleshooting flowchart.

TCM

TEST HARNESS

Terminal Locations

TCM Reset Procedure

Turn the ignition switch off. -

, Remove the CLOCK fuse (7.5 A) from the main relay box for 10 seconds to reset the TCM.

1

2

NOTE: Disconnecting the CLOCK fuse also cancels the radio preset stations and the clock setting. Make note of the
radio presets before removing the fuse so you can reset them.
Final Procedure NOTE: This procedure must be done after any troubleshooting.
1. Remove the jumper wire from the Service Check Connector.
2. Reset the TCM. 3. Set the radio preset stations and clock setting.
Only the A and D terminals of the Test Harness are used for A/T troubleshooting.

Unless otherwise noted, use only the Digital Multimeter, KS—AHM —32—003, for testing.

07LAJ-PT3010A

NOTE:ProCarManuals.com

If a customer describes the symptoms for codes 3, 6, 11, 14 or 1 5 yet the indicator light is not blinking, it will
be necessary to recreate the symptom by test driving, and then checking the indicator light with the ignition

still
ON.
If the indicator light displays codes 1,2,3,8, 11, or 16, check first the No. 9, 13 and 18 and fuse before elec-
trical troubleshooting.
If any of the fuses have blown, repair them and then recheck. If the indicator light displays codes other than those listed above or stays lit continuously, the TCM is faulty.
Sometimes the indicator light and the Malfunction Indicator Lamp (MID/Check Engine light may come on
simultaneously. If so, check the PGM-FI system according to the number of blinks on the MIL/Check Engine light,
then reset the memory by removing the CLOCK fuse in the main relay box for more than 10 seconds. Drive the vehicle for several minutes at speed over 30 mph (50 km/h), then recheck the MIL/Check Engine light.PGM-FI system

The PGM-FI system on this model is a sequential multiport fuel injectin system.
The indicator light may comes on, indicating a system problem, when, in fact, there is a poor or intermittent
electrical connection. First, check the electrical connections, clean or repair connections if necessary.If the electrical readings are not as specified when using the test harness, check the test harness connections
before proceeding.
Disconnecting the CLOCK fuse also cancels the radio preset stations and the clock setting. Make note of the radio
presets before removing the fuse so you can reset them. If the self-diagnosis indicator light does not blink, perform an inspection according to the table listed below.
Symptom
• Lock-up clutch does not
engage.

• Transmission jerks hard when shifting.
• Transmission jerks hard when
shifting.

• Transmission jerks hard when
shifting

• Lock-up clutch does not

engage.
14-7214-70 14-68
14-67

Refer to

page

Possible Cause
• Disconnected gauge assembly connector
• Short or open in tachometer wire
• Faulty tachometer
• Short or open in FAS (PNK) wire between D16 terminal and

ECM.

• Trouble in ECM
• Disconnected mainshaft speed sensor connector
• Short or open in mainshaft speed sensor wire
• Faulty mainshaft speed sensor
• Disconnected linear solenoid connector
• Short or open in linear solenoid wire
• Faulty linear solenoid
Blinks

OFF

OFF

OFF

When the ignition

switch is turned on,
indicator light
Number of indicator light

blinks while Service CheckConnector is jumped.

11

14

15

16


Ref.page

14-74
14-76
14-77
14-78
NOTE:ProCarManuals.com

6. After insetting a flat tip screwdriver, turn it 90°.

HOOK

CENTER AIR

VENT

30 mm

(1.2
in)

FLAT TIP

SCREWDRIVER

7. Inset the tip of a flat tip screwdriver in under the

hook by turning a flat tip screwdriver. Detach the

hook by prying it.

HOOK

CENTER AIR

VENT

FLAT TIP

SCREWDRIVER
8. Pull the center air vent backward while prying the

hook.

CAUTION: Use a shop towel on the dashboard to

prevent damage.

DASHBOARD
HOOK

CENTER AIR

VENT

SHOP TOWEL

FLAT TIP SCREWDRIVER

9. Detach the another hook as the same work, then

remove the center air vent.

CENTER AIR

VENT

HOOKS

10. Install the center air vent and clock.

NOTE:

DASHBOARD

Make sure the connector of the clock is con-

nected properly.

(cont'd)
If there is a minor dent on the dashboard, repair

it by hand as shown.ProCarManuals.com

Ignition Timing Inspection and Setting

1. Start the engine and allow it to warm up (radiator
fan comes on).
2. Pull out the service check connector located under the middle of the dash. Connector the BLU andGRN/WHT terminals with a jumper wire (see sec-

tion 11).

3. Check the idle speed (see page 23-92).
4. Connect a timing light to the service loop; while the
engine idles, point the light toward the pointer on

the timing belt cover.
SERVICE LOOP

TIMING LIGHT

5. If necessary, adjust ignition timing to the following specifications:
Ignition Timing: 15° ±2° BTDC (RED mark)
Idle Speed (rpm):
NOTE: All electrical systems turned OFF. POINTER
RED MARK
CRANKSHAFT PULLEY
WHITE MARK
6. If necessary, adjust the ignition timing, adjust by turning the adjusting screw on the ignition timingadjuster in the control box.
Remove the control box cover. 7. Remove the jumper wire from the service check
connector.
8. After adjusting, reinstall the cover on the ignition timing adjuster with new rivets.ADJUSTING SCREW
To ADVANCE
To RETARD Reconnect the adjuster to the car, start the
engine, and turn the adjusting screw
counterclockwise to retard the timing, or
clockwise to advance it, as necessary.
CAUTION: Do not damage the adjuster when
removing the rivets. Remove the ignition timing adjuster from the
control box.

Drill the two rivets off with a 3/16 in. drill bit,

then separate the cover from the adjuster. 3-P CONNECTORCONTROL BOX

IGNITION TIMING

ADJUSTER
Remove the two screws from the control box
then disconnect the 3-P connector from the igni-

tion timing adjuster.ProCarManuals.com

Idle Control System

Idle Speed Setting

Inspection/Adjustment
1. Start the engine and warm it up to normal operating temperature (the cooling fan comes on).
2. Connect a tachometer. Connect a tachometer to loop of igniter unit
secondary, or... 3. Disconnect the 2P connector from the EACV.

EACV

TACHOMETER
IGNITER
UNIT

4. Start the engine with the accelerator pedal slightlydepressed, then turn the headlights and rear defog-
ger ON. After the Check Engine light comes on,stabilize the rpm at 1000, then slowly release the
pedal until the engine idles. If the engine stalls, turn the idle adjusting screw
one turn counterclockwise and recheck.
5. Check idling with the headlights and rear defogger
on.

Idle speed should be:
Remove the rubber cap from the tachometer
connector and connect a tachometer.

TACHOMETER

RUBBER

CAP
Adjust the idle speed, if necessary, by turning
the idle adjusting screw. If the proper idle speed cannot be achieved,
clean the throttle body port with carburetor

cleaner.

IDLE ADJUSTING

SCREW

TACHOMETER CONNECTORProCarManuals.com