battery ASTON MARTIN V8 VANTAGE 2010 User Guide

Seating (01.10)
Body System (01.00)
Issue 4, November 2008 Workshop Manual 1-7-1
Body System (01.00)
Seating (01.10)
Description
The front seats are installed with the following features:
• Integral side airbags
•Head restraints
• Safety belt reel pretensioner
• Electrically adjustable seat positioning and lumbar support
• Heated seat (optional)
Heated Seats
The heated seat system comprises:
• Heated seat switches
• Backrest heater element
• Cushion heater element and thermostat
The heated seat function permits the electrical heating of the
seat back and cushion on the driver and front passenger
seats. The heating system of each seat is selected by separate
switches located on the inside of each seat base.
Once the heated seat function has been activated, it will
operate until one of the following conditions have been
satisfied:
• A fixed period of time has expired (10 minutes)
• If the engine is not running and the ignition key is removed
• A malfunction is detected by the heated seat module
Confirmation that the heated seat function is active is
indicated by the illumination of an amber light on the
switch.
Specifications Maintenance
RH/LH Front Seat - Remove and Install
Remove
1. Power seat fully forward.
2. Remove bolts (x2), securing rear of seat to seat rails.
3. Power seat fully rearwards.
4. Disconnect vehicle battery.
5. Remove bolt securing se
at belt to seat frame.
6. Remove bolts (x2), securing front of seat to seat rails.
7. Tip the seat forwards and disconnect multiplugs (x4).
8. Protect sill plate and trim prior to seat removal.
9. With assistance, remove seat assembly.
Install
1. With assistance, Install seat in the vehicle.
2. Position seat belt to seat frame, install and torque tighten bolt.
3. Tip the seat forwards and connect multiplugs (x4).
4. Position seat onto seat rails.
5. Remove sill plate protection.
6. Connect vehicle battery.
7. Install front bolts (x2. Power seat forward and install rear bolts (x2). Torque tighten bolts (x4).
Front Seat Squab Cover Assembly (Each,
Pre-08MY) - Remove and Install
Remove
1. Remove seat (see Workshop Manual procedure 01.10.AB Seat Assembly - Front - LH - Remove for
Access and Refit).
Torque Figures
DescriptionNm
Seat mountings 20-25
Seatbelt 15-20
Repair Operation Time (ROT)
Repair Operation Time (ROT)

Seating (01.10)
Body System (01.00)1-7-4 Workshop Manual Issue 4, November 2008
Removal
1. Remove 6 way height adjust er (see Workshop Manual
procedure 01.10.AE 6 Way Height Adjuster - Including
Motors - Renew).
2. Remove screws (x3) heater and lumbar switch assembly
(see Figure 1).
3. Release switch assembly and disconnect multiplug
4. Release cover from cushion frame assembly (see Figure 2). 5. Pull seat cushion cover from between squab and
cushion frames and remove cover (see Figure 3).
Installation
1. Connect multiplugs (x2) heater and lumber switch assembly.
2. Install switch assembly to seat
3. Ease cover over cushion foam attach to velcro.
4. Push cushion flap between cushion and squab and secure to cushion frame assembly.
5. Secure cushion cover to sides and front edge of seat cushion frame assembly.
6. Install 6 way height adjust er (see Workshop Manual
procedure 01.10.AE 6 Way He ight Adjuster - Including
Motors - Renew).
6-Way Height Adjuster (Inc. Motors) -
Renew
Removal
1. Power seat fully forward.
2. Remove bolts (x2) securing rear of seat to seat rails.
3. Power seat fully rearwards.
4. Remove bolts (x2) securing front of seat to seat rails.
5. Battery isolation switch ‘OFF’.
6. Remove bolt securing seat belt to seat frame.
7. Tip the seat forwards and disconnect multiplugs (x4).
8. With assistance, remove seat assembly.
9. Remove screw (x1) relay to seat cushion base.
Figure 1
Figure 2
A0110287
A0110288
Figure 3
Repair Operation Time (ROT)
ItemCode
6-Way Height Adjuster-Renew 01.10.AE
A0110290

Seating (01.10)
Body System (01.00)1-7-6 Workshop Manual Issue 4, November 2008
16. Slide 6 way height adjuster to release and remove adjuster from seat assembly (see Figure 5).
Installation
1. Install relay to seat cushion base.
2. Connect multiplugs (x3) and secure to 6 way adjuster frame.
3. Secure seat belt buckle harness (cable ties x4) to 6 way seat adjuster frame assembly.
4. Install a new bolt that attaches the seat belt buckle.
5. Position 6 way height adju ster to seat cushion frame
assembly and install screws (x4).
6. With assistance, install seat in the vehicle.
7. Position seat belt to seat frame, install and torque tighten bolt.
8. Tip seat forwards and connect multiplugs (x4).
9. Position seat onto seat rails.
10. Battery isolation switch ‘ON’.
11. Install front bolts (x2), Power seat forward and install rear bolts (x2). Torque tighten bolts (x 4).
Squab Motor Kit - Renew
Removal
1. Remove squab cover (see Workshop Manual procedure 01.10.AC Cover Assembly - Front Seat Squab - Each -
Renew). 2. Disconnect heater multiplug and remove squab foam
(see Figure 1).
3. Release top mountings of lumbar adjust frame and move to access squab motor (see Figure 2).
Figure 5
Repair Operation Time (ROT)
A0110292
Figure 1
Figure 2
A0110293
A0110282

Seating (01.10)
Body System (01.00)
Issue 4, November 2008 Workshop Manual 1-7-9
Front Seat Buckle Assembly - Renew
Removal
1. Power seat fully forward.
2. Remove bolts (x2) securing rear of seat to seat rails.
3. Power seat fully rearwards.
4. Remove bolts (x2) securing front of seat to seat rails.
5. Battery isolation switch ‘OFF’.
6. Remove bolt securing seat belt to seat frame.
7. Tip the seat forwards and disconnect multiplugs (x4).
8. With assistance, remove seat assembly.
9. Release multiplug (x1) seat belt buckle harness to 6 way
seat adjuster frame assembly.
10. Release cable ties (x4) securing seat belt buckle harness to 6 way seat adjuster frame assembly (see Figure 1). 11. Remove bolt (x1) seat belt buckle to frame (see Figure
2).
12. Remove seat belt buckle assembly.
Installation
1. Secure harness and multiplug to 6 way seat adjuster frame assembly.
2. Install seat belt buckle.
3. With assistance, install seat in the vehicle.
4. Position seat belt to seat frame, install and torque tighten bolt.
5. Tip seat forwards and connect multiplugs (x4).
6. Position seat onto seat rails.
7. Battery isolation switch ‘ON’.
8. Install front bolts (x2), Power seat forward and install rear bolts (x2). Torque tighten bolts (x 4).
Valance Heater and Lumbar Switch
Assembly - Renew
Removal
1. Power seat fully forward.
2. Remove bolts (x2) securing rear of seat to seat rails.
3. Power seat fully rearwards.
4. Remove bolts (x2) securing front of seat to seat rails.
5. Disconnect vehicle battery.
Repair Operation Time (ROT)
A0110289B
Figure 2
Repair Operation Time (ROT)
A0110287A

Seating (01.10)
Body System (01.00)1-7-10 Workshop Manual Issue 4, November 2008
6. Tip the seat backwards and remove screws (x3) heater and lumbar switch assembly to seat (see Figure 1).
7. Release switch assembly from seat.
8. Disconnect multiplug (x2) and remove switch assembly (see Figure 2).
Installation
1. Connect multiplugs (x2) switch assembly.
2. Install switch assembly (screws x3).
3. Position seat onto seat rails.
4. Connect vehicle battery
5. Install front bolts (x2), Power seat forward and install rear bolts (x2). Torque tighten bolts (x 4).
Seat Harness Kit - Renew
Removal
1. Remove seat 6 way height adjuster (see Workshop Manual procedure 01.10.AE 6 Way Height Adjuster -
Inc. Motors - Renew). 2. Remove release lever (see Figure 1).
3. Remove lever cover (see Figure 2).
4. Disconnect airbag multiplu
g and release from bracket
(see Figure 3).
Figure 1
Figure 2
Repair Operation Time (ROT)
A0110287
A0110286
Figure 1
Figure 2
Figure 3
A0110296
A0110296A
A0110281

Glass, Frame and Mechanism (01.11)
Body System (01.00)
May 2007 Workshop Manual 1-8-1
Body System (01.00)
Glass, Frame and Mechanism (01.11)
Description
Power to the door window regulator motor is available when
the ignition switch is at position ‘0’ and is supplied, through
a thermal cut-out, to the left and right window switches. The
switches are double pole earth so that the current through a
window regulator motor may be switched in either direction
to raise or lower the glass.
Frameless doors
To avoid damaging the body seals during door opening, the
door glass must be lowered before the door can be opened.
This function is controlled by the door modules.
The door module senses the rotation of the latch claw as the
door opens, the door module then drives the door window
regulator motor briefly to lower the door glass until it clears
the glass seals. After closing a door, the window regulator
motor operates to raise the door glass to seat against the
body seals.
Specifications
Maintenance
Glass Regulator - Renew
Removal
1. Remove door trimboard assembly (see Workshop Manual procedure 01.05.CB Trimboard Assembly -
Door - Remove for Access and Refit).
2. Remove screws (x4) securi ng switchpack to trimboard
assembly, remove switchpack.
3. Connect switchpack to door cable harness multiplug (x1).
4. With power on raise/lower gl ass to access glass clamping
bolts (x2).
5. Battery isolation switch ‘OFF’. 6. Mark the glass around the rear clamp.
7. Remove clamping bolts (x2)
and lift glass out of door
(see Figure 1).
8. Remove nuts (x4) securing door glass regulator mechanism (see Figure 2).
9. Disconnect multiplug from regulator motor.
WAR NI N G
PUT ON PROTECTIVE GLOVES AND EYE
PROTECTION WHEN YOU HOLD THE GLASS
COMPONENTS.
THE GLASS CAN BREAK EASILY AND CAUSE INJURY.
Torque Figures
DescriptionNm
Regulator mountings 9.0 (M6)
10-15 (M10)
Glass grip screws 5.0 - 6.0
Repair Operation Time (ROT)
WA R N I N G
PUT ON PROTECTIVE GLOVES AND EYE
PROTECTION WHEN YO U HOLD THE GLASS
COMPONENTS.
THE GLASS CAN BREAK EASILY AND CAUSE INJURY.
Figure 1
Figure 2







Glass, Frame and Mechanism (01.11)
Body System (01.00)1-8-2 Workshop Manual May 2007
10. Remove screws (x3) securing regulator motor to door frame (see Figure 3).
11. Carefully remove regula tor mechanism and regulator
motor out through the larger door frame aperture (see
Figure 4).
Installation
1. Install regulator mechanism and motor, install and torque tighten nuts (x4) and screws (x3). 2. Connect multiplug to regulator motor.
3. Fit glass into door and enga
ge the clamping brackets to
the marked position, install clamping bolts and partially
tighten.
4. Battery isolation switch ‘ON’.
5. Raise glass to fully up and adjust alignment, lower fully and check alignment, repeat until alignment is correct,
finally torque tighten clamping bolts (x2).
6. Disconnect switchpack multiplug, install switchpack on trimboard, install and tighten screws (x4).
7. Install door trimboard asse mbly (see Workshop Manual
procedure 01.05.CB Trimboard Assembly - Door -
Remove for Access and Refit).
RH/LH Door Glass - Renew
Removal
1. Remove door trimboard assembly (see Workshop
Manual procedure 01.05.CB Trimboard Assembly -
Door - Remove for Access and Refit).
2. Set glass position to access clamping bolts (x2) through apertures in door frame (see Figure 1).
Figure 3
Figure 4






WAR NI NG
PUT ON PROTECTIVE GLOVES AND EYE
PROTECTION WHEN YOU HOLD THE GLASS COMPONENTS.
THE GLASS CAN BREAK EASILY AND CAUSE INJURY.
Repair Operation Time (ROT)
ItemCode
Door Glass-Renew RH01.11.BA
Door Glass-Renew LH01.11.BC
Figure 1




Instrument Panel (IP) (01.12)
Body System (01.00)
Issue 5, January 2010 Workshop Manual 1-9-1
Body System (01.00)
Instrument Panel (IP) (01.12)
Specifications
Maintenance
Instrument Panel - Renew
Removal
1. Disconnect vehicle battery.
2. Drain cooling system (see Workshop Procedure 03.03.AD Coolant - Drain and Refill).
3. Evacuate air conditioning system (see Workshop Procedure 12.03.FA Tank - Receiver Drier - Renew).
4. Remove RH door (see Work shop Procedure 01.03.EA
Door Assembly - RH - Remo ve for Access and Refit).
5. Remove LH front seat (see Workshop Manual 01.10.AB
Seat Assembly - Front - LH - Remove for Access and
Refit).
6. Remove RH front seat (see Workshop Manual 01.10.AA Seat Assembly - Front - RH - Remove for Access and
Refit). 7. Remove tread plate badges - screws x2 (see Figure1).
8. Remove screws (x12) 6 each
side and remove LH and
RH side tread plates.
9. Release door seal from d oor aperture (see Figure 2).
Torque Figures
DescriptionNm
IP Mountings 22.5
Glue pot bolts 8
Blower motor to bulkhead 10-14
Repair Operation Time (ROT)
01-12-013
Figure 1
Figure 2

Instrument Panel (IP) (01.12)
Body System (01.00)1-9-6 Workshop Manual Issue 5, January 2010
39. Install LH front seat (see Workshop Manual 01.10.AB Seat Assembly - Front - LH - Remove for Access and
Refit).
40. Fill cooling system (see Workshop Manual 03.03.AD
Coolant - Drain and Refill).
41. Re-charge air conditioni ng system (see Workshop
Manual 12.03.FA Tank - Receiver Drier - Renew).
42. Connect vehicle battery.
Airbag Panel and Door Assembly -
Renew
Removal
1. Remove glovebox assembly (see Workshop Manual
procedure 01.12.AL Glovebox Assembly - Renew).
2. Remove glovebox shield (see Figure 1).
3. Remove the bolts (x3) that secure the airbag panel and
door assembly plate to the chassis (see Figure 2)
.
4. Remove airbag panel and d oor assembly (5 clips) (see
Figure3).
Installation
1. Install airbag panel and door assembly (5 clips).
2. Through glovebox aperture, install support right-angled bar and secure bolts (x3).
3. Remove and clean double-sided taped from glovebox shield, apply new tape and install.
4. Install glovebox assembly (see Workshop Manual procedure 01.12.AL Gloveb ox Assembly - Renew).
Glovebox Assembly - Renew
Removal
1. Remove passenger lower panel assembly (5 clips and
multiplug).
2. Remove the securing screws holding the glove box hinge to the chassis (x2).
3. Support the glove box and locate the latch mechanism.
4. Using a suitable tool press the latch mechanism to release the glove box.
5. Support the glove box and detach the buffer cord from the glove box.
Installation
1. Support glovebox and attach the buffer cord (ensure the cord is through correct aperture).
2. Install glovebox into aperture and press top to latch.
3. Align the glovebox hinge an d secure with screws (x2)
including spacers between the hinge and chassis.
4. Install passenger lower panel assembly (5 clips and 1 multiplug).
Repair Operation Time (ROT)
Figure 3
Repair Operation Time (ROT)
ItemCode
Glovebox Assembly-Renew 01.12.AL

Instrument Panel (IP) (01.12)
Body System (01.00)1-9-12 Workshop Manual Issue 5, January 2010
2. Disconnect multiplug (x1) starter button and remove panel assembly (see Figure 1).
3. Remove starter button from instrument panel bezel
assembly (see Figure 2). 4. Remove screws (x6) air vent
s (x2) to bezel assembly and
remove air vents (s ee Figure 3).
Installation
1. Install air vents (x2).
2. Install starter button.
3. Position panel assembly, connect multiplug (x1) starter
button.
4. Install panel and secure in clips (x4).
Rear Console Panel Assembly - Renew
Removal
1. Battery isolation switch ‘OFF’
2. Remove stowage compartment door.
3. Remove bolt and screws (x5), support rail to body. Remove support rail.
4. Remove screw (x1) centre arm rest to rear console panel assembly.
5. Release/remove centre arm rest.
6. Remove nuts (x3), screws (x4), panel assembly rear console.
7. Remove screws (x2) ashtray console panel assembly to floor.
8. Remove rear console panel assembly.
Figure 1
Figure 2
A0112218
A0112217
Figure 3
Repair Operation Time (ROT)
ItemCode
Rear Console Panel Assembly-Renew 01.12.CA
A0112217A