cooling AUDI A4 1997 B5 / 1.G APB Engine Cooling System Components
Page 27 of 34
19-25
- Start engine and let it idle for about 10
minutes.
- Maintain an engine speed of about 2000 RPM
for about 5 minutes.
- Allow engine to run at idling speed until bottom
hose on radiator becomes hot.
- Check coolant level and top up if necessary.
When engine is at normal operating temperature
coolant level must be on max. mark, and
between min. and max. marks when engine is
cold.
Note:
When the engine is hot the cooling system is
under pressure. Carefully open filler cap on
expansion tank to release pressure before
starting repair work.
WARNING!
Hot steam can escape from the expansion
tank when the filler cap is opened. Cover the
filler cap with a cloth and remove it carefully.
Pa
ge 27 of 34 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.19.1
Page 29 of 34
19-27
Vehicles with air conditioner
WARNING!
Do not open the air conditioner refrigerant circuit.
Note:
To prevent damage to the condenser and refrigerant lines and hoses,
ensure that the lines and hoses are not stretched, kinked or bent. - Unbolt pressurizing fan and detach cooling lines for power steering
hydraulic fluid -arrows-.
- Detach air cowls from radiator -4- (left and right).
- Remove securing bolts -1- and -2- for condenser.
- Unplug connector -3- from air conditioner pressure switch -F129.
- Lift condenser up out of its bracket, turn it towards side and secure to
right-hand front wheel with wire.
Pa
ge 29 of 34 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.19.1
Page 30 of 34
19-28
Installing
Install in the opposite order to removing. When installing, note the
following points:
Tightening torques - Release two retaining pins for radiator and pull out upward -arrows-.
- Pivot radiator toward front and lift out.
- Fill with coolant Page 19
-19
.
Component
Nm
Condenser to radiator 10
Cooling lines to radiator 10
Pressurizing fan to radiator 10
Pa
ge 30 of 34 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.19.1
Page 34 of 34
19-31
Installing
Install in the opposite order to removing. When
installing, note the following points:
- Remove residues of sealant on sealing surfaces
of coolant pump and cylinder block.
- Clean sealing surfaces; ensure that they are free
of oil and grease.
- Fit new gasket on coolant pump flange.
- Insert coolant pump into cylinder block and tighten all 9 securing bolts -
2-.
- Secure rear toothed belt guard at coolant pump housing -1-.
Tightening torque: 10 Nm.
- Install toothed belt Page 13
-4 .
- Install ribbed belt Page 13
-1 .
- Install toothed belt guard.
- Fill cooling system Page 19
-19
.
Pa
ge 34 of 34 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.19.1