instrument cluster AUDI A4 1998 B5 / 1.G APB Engine Motronic Syst
Page 2 of 166
01-2
      
The Exhaust Malfunction Indicator Light (MIL) in 
the instrument cluster will be switched on if the 
engine control module recognizes malfunctions 
which have an affect (decrease emissions) on 
exhaust emissions   Page 01
-3 . 
     
Malfunctions relating to the electronic throttle 
are also indicated by a Electronic Power 
Control (EPC) warning light in the instrument 
cluster. 
Pa
ge 2 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 22 of 166
01-19
 Diagnostic Trouble Code (DTC) table
 
Notes:  
 
If malfunctions occur in the sensors and components being monitored, they will be stored in the DTC memory together 
with an indication of the type of malfunction. Notes on Engine Power Control (EPC) (drive by wire)   Page 24
-139
 . 
 Malfunctions relating to the electronic throttle are also indicated by the EPC (Electronic Power Control) warning light in the 
instrument cluster. 
 Malfunction which decrease exhaust emissions are indicated by an Exhaust Malfunction Indicator Light (MIL), the MIL is 
located in the instrument cluster. As soon as certain malfunction are recognized, the MIL is switched on immediately. 
There are also malfunctions, were the MIL is switched on only after the engine is started again. 
 Sporadically occurring malfunctions (temporary malfunctions) will be indicated on the VAG1551 display as "SP."
 The DTC table is arranged according to the 5-digit DTC in the left-hand column.
 If a malfunction is stored in the DTC memory and then does not occur again during the next 40 engine warm-up phases, 
the DTC will be automatically erased. 
 Components that are indicated as being faulty by the VAG1551 should not be replaced immediately. Always start by 
checking the wiring, connectors and Ground (GND) connections for the component using the current wiring diagram. This 
is particularly important in the case of sporadic malfunctions (indicated by the letters "SP"on the scan tool display). 
 If the connector for the engine control module is disconnected or if the battery is disconnected, all the learned values 
(adaptation values) stored in the control module will be erased, although the contents of the DTC memory will remain 
intact. The next time the engine is started the idling may be rough at first. In this case let the engine run at idle for a few 
Pa
ge 22 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 48 of 166
01-39
 
DTC  
Description of malfunction  
Corrective action  
SAE  
VAG  
  
  
P1171   17579   Throttle Actuation Potentiometer 
Signal 2  
Range/Performance
 1) 3)
  - Check throttle actuation potentiometer   Page 24
-153
 .
P1172   17580   Throttle Actuation Potentiometer 
Signal 2  
Signal too Low
 1) 3)
    
  
P1173   17581   Throttle Actuation Potentiometer 
Signal 2  
Signal too High
 1) 3)
    
  
P1176   17584   O2 Correction Behind Catalyst, B1  
Limit Attained 
2)  - Check oxygen sensor aging of oxygen sensors before catalytic 
converters  Page 24
-93
 
P1177   17585   O2 Correction Behind Catalyst, B2  
Limit Attained 
2)  - Check oxygen sensors and  
oxygen sensor control behind catalytic converters   Page 24
-100
1) With this malfunction the EPC (Electronic Power Control) Malfunction Indicator Light (MIL) in the instrument cluster is 
switched on by the ECM immediately after the malfunction has been recognized. Significance of EPC malfunction indicator 
light  Page 24
-142
 .  
2) With this malfunction the exhaust Malfunction Indicator Light (MIL) is only switched on by the ECM, if the malfunction is 
recognized after the engine has been restarted. Significance of MIL   Page 01
-3 .  
Pa
ge 48 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 53 of 166
01-43
 
DTC  
Description of malfunction  
Corrective action  
SAE  
VAG  
  
  
P1250   17658   Fuel Level  
Too Low 
4)  
 Repair Manual, Electrical Equipment, Repair Group 01
    - Fill fuel tank and erase DTC memory
- Check DTC memory from instrument cluster.
4) The malfunction "Fuel Level too Low" will be stored if the fuel level in the tank is or was too low. The malfunction remains as 
a static malfunction and will not be set a sporadic malfunction even if the customer fills the tank with fuel in the meantime. 
Therefore it is possible to recognize malfunctions which have been stored due to lack of fuel e.g.: misfiring or malfunction 
regarding oxygen sensor control.  
Pa
ge 53 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 56 of 166
01-46
 
DTC  
Description of malfunction  
Corrective action  
SAE  
VAG  
  
  
P1335   17743   Engine Torque Monitoring 2  
Control Limit Exceeded 
1) 3)
  - Check hoses   Page 24
-170
 
- Check Intake Air Temperature (IAT) sensor   Page 28
-17
- Check Mass Air Flow (MAF) sensor   Page 24
-59
- Check Engine Coolant Temperature (ECT) sensor   Page 28
-25
P1336   17744   Engine Torque Monitoring  
Adaptation at limit  - Check hoses   Page 24
-170
 
- Check Intake Air Temperature (IAT) sensor   Page 28
-17
- Check Mass Air Flow (MAF) sensor   Page 24
-59
- Check Engine Coolant Temperature (ECT) sensor   Page 28
-25
1) With this malfunction the EPC (Electronic Power Control) Malfunction Indicator Light (MIL) in the instrument cluster is 
switched on by the ECM. Significance of EPC malfunction indicator light   Page 24
-142
 .  
3) With this malfunction the exhaust Malfunction Indicator Light (MIL) is switched on by the ECM, immidiately after the 
malfunction has been recognized. Significance of MIL   Page 01
-3 .  
Pa
ge 56 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 61 of 166
01-51
 
DTC  
Description of malfunction  
Corrective action  
SAE  
VAG  
  
  
P1386   17794   Internal Control Module  
Knock Control Circ.Error  - Replace Engine Control Module (ECM)   Page 24
-24
P1387   17795   Internal Control Module  
Altitude Sensor Error
 2)
    
P1388   17796   Internal Control Module  
Drive by wire error 
1) 3)
    
1) With this malfunction the EPC (Electronic Power Control) Malfunction Indicator Light (MIL) in the instrument cluster is 
switched on by the ECM. Significance of EPC malfunction indicator light   Page 24
-142
 .  
2) With this malfunction the exhaust Malfunction Indicator Light (MIL) is only switched on by the ECM, if the malfunction is 
recognized after the engine has been restarted. Significance of MIL   Page 01
-3 .  
3) With this malfunction the exhaust Malfunction Indicator Light (MIL) is switched on by the ECM, immediately after the 
malfunction has been recognized. Significance of MIL   Page 01
-3 .  
Pa
ge 61 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 77 of 166
P1548   17956   Boost Pressure 
Contr.Valve  
Open    
  1) With this malfunction the EPC (Electronic Power Control) Malfunction Indicator Light (MIL) in the instrument cluster is 
switched on by the ECM immediately after the malfunction has been recognized. Significance of EPC malfunction indicator 
light  Page 24
-142
 .  
3) With this malfunction the exhaust Malfunction Indicator Light (MIL) is switched on by the ECM, immidiately after the 
malfunction has been recognized. Significance of MIL   Page 01
-3 .  
Pa
ge 77 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 79 of 166
01-66
 
DTC  
Description of malfunction  
Corrective action  
SAE  
VAG  
  
  
P1558   17966   Throttle Actuator  
Electrical Malfunction 
1)3)
  - Check throttle valve control module   Page 24
-145
P1559   17967   Idle Speed Contr. Throttle Pos.  
Adaptation Malfunction 
2)  - Perform adaptation   Page 24
-146
P1560   17968   Maximum Engine Speed Exceeded  
- Repair mechanical damage
P1564   17972   Idle Speed Control Throttle Position  
Low Voltage During Adaptation  - Charge battery or repeat adaptation   Page 24
-146
P1565   17973   Idle Speed Control Throttle Position  
Lower Limit not Attained 
1) 3)
  - Check throttle valve control module   Page 24
-145
P1568   17976   Idle Speed Control Throttle Position  
Mechanical Malfunction 
1) 3)
    
1) With this malfunction the EPC (Electronic Power Control) Malfunction Indicator Light (MIL) in the instrument cluster is 
switched on by the ECM. Significance of EPC malfunction indicator light   Page 24
-142
 .  
2) With this malfunction the exhaust Malfunction Indicator Light (MIL) is only switched on by the ECM, if the malfunction is 
recognized after the engine has been restarted. Significance of MIL   Page 01
-3 .  
3) With this malfunction the exhaust Malfunction Indicator Light (MIL) is switched on by the ECM, immediately after the 
Pa
ge 79 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 82 of 166
01-68
 
DTC  
Description of 
malfunction  
Corrective action  
SAE  
VAG  
  
  
P1603   18011   Internal Control Module 
Malfunction 
2)  - Replace Engine Control Module (ECM)   Page 24
-24
 .
P1604   18012   Internal Control Module 
Malfunction 
1)3)
    
P1606   18014   Rough Road Spec Engine 
Torque ABS-ECU  
Electrical Malfunction  
 Electrical Wiring Diagrams, Troubleshooting & Component Locations    - Check wire connection between ECM and ABS control module   Page 24
-
198
 
P1609   18017   Crash shut-down 
activated  Accident with airbag triggered or a output Test Diagnostic Mode (TDM) has 
been carried out, therefore erase DTC Memory in ECM; Notes crash signal   
Page 24
-196
   
P1612   18020   Electronic Control Module 
2)  
Incorrect Coding  - Check or code Engine Control Module (ECM)   Page 01
-93
1) With this malfunction the EPC (Electronic Power Control) Malfunction Indicator Light (MIL) in the instrument cluster is 
switched on by the ECM. Significance of EPC malfunction indicator light   Page 24
-142
 .  
2) With this malfunction the exhaust Malfunction Indicator Light (MIL) is only switched on by the ECM, if the malfunction is 
recognized after the engine has been restarted. Significance of MIL   Page 01
-3 .  
3) With this malfunction the exhaust Malfunction Indicator Light (MIL) is switched on by the ECM, immediately after the 
malfunction has been recognized. Significance of MIL   Page 01
-3 .  
Pa
ge 82 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 83 of 166
01-69
 
DTC  
Description of malfunction  
Corrective action  
SAE  
VAG  
  
  
P1620   18028   Engine coolant temperature signal  
Open/short to B+    
P1621   18029   Engine coolant temperature signal  
Short to ground  - Check coolant temperature signal   Page 24
-181
P1622   18030   Engine coolant temperature signal  
Range/Performance    Note for malfunctions P1620, P1621 and P1622:  
The Engine Control Module (ECM) receives the "Coolant temperature signal" from the instrument cluster. When the ECM 
receives this signal the boost pressure will be decreased. 
Pa
ge 83 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1