AUDI A6 1996 C5 / 2.G 01V Transmission Read Measuring Value Block E 17 Service Manual

01-220
Only for transmission with hydraulic control E17
Display
group
number Display
field Description
Test requirements
Spec. value on
V.A.G 1551
display Corrective actions
008
4 Signal for
deceleration/engine under
load While
driving
1) Deceleration
mode Deceleration For declines or delay
(engine brake)


Engine under
load
- Engine is under load in
normal driving
conditions.
1) While driving, a second mechanic is required to read specifications. 2) Only for vehicles with CAN-bus For information on which vehicles are equipped with CAN-bus
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, unit allocation, ratios, equipment

3) Only for vehicles without CAN-bus For information on which vehicles are equipped with CAN-bus
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, unit allocation, ratios, equipment

Pa
ge 41 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-221
Only for transmission with hydraulic control -E17-
Display
group
number Display
field Description
Test requirements
Spec. value
on V.A.G
1551
display Corrective actions
009

with
CAN-bus 1 Engine torque
(actual) while driving
1)
...Nm
The signal for actual engine torque is
transmitted by the Engine Control Module
(ECM) to the Transmission Control Module
(TCM) via the CAN-bus wiring.

2 Maximum
torque while driving 1)
...Nm
The engine torque required (reduced) by
the TCM during the shifting process
2)

3 Engine RPM with engine running approx.
0...8200
RPM - See DTC table, DTC 529 and 543
page 01
-45


4 Throttle valve
value while
standing Idle
1)
0...1 % When accelerating from idle to WOT, %-
value increases steadily.


Wide Open
Throttle
(WOT)
99...100 % - See DTC table, DTC 518 page 01
-45
Pa
ge 42 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

Notes and footnotes for display group number 009 for vehicles with CAN-bus are on the next page.
Pa
ge 43 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-222
1) While driving, a second mechanic is required to read specifications. 2) While driving in one gear, the indicated shifting torque remains constantly high, since no torque reduction is required.
Notes for display group number 009;
This display group number 009 is only valid for vehicles with CAN-bus, refer to display group number 009 on next page for
vehicles without CAN-bus. A)
A) There is a distinction made between vehicles with and without CAN-bus. For information on which vehicles are equipped
with CAN-bus
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, unit allocation, ratios, equipment

Pa
ge 44 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-223
Only for transmission with hydraulic control E17
Display
group
number Display
field Description
Test
requirements Spec. value
on V.A.G
1551
display Corrective actions
009

without
CAN-bus 1 Engine torque
(actual) While driving
1)
Nm
Engine torque is calculated by the
Transmission Control Module (TCM) based
on fuel consumption signal and engine
speed signal.

2 Engine RPM With engine
running approx.
0...8200
RPM - See DTC table, DTC 529 and 543
page 01
-45

- Perform electrical test page 01
-273

3 Throttle valve
value See display group number 2, display field 2

4 Fuel consumption
signal (high time) While driving
1)
ms Not applicable
1) While driving a second mechanic is required to read specifications.
Notes for display group number 009 see next page;
Pa
ge 45 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-224
Notes for display group number 009;

This display group number 009 is only valid for vehicles without CAN-bus, refer to previous display group number 009 for
vehicles with CAN-bus. A)
For vehicles with motronic injection and ignition systems, engine torque is transmitted by the Engine Control Module
(ECM). For these vehicles, the fuel consumption display is omitted or always indicates "00ms".
A) There is a distinction made between vehicles with and without CAN-bus. For information on which vehicles are equipped
with CAN-bus
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, aggregate allocation, ratios,
equipment

Pa
ge 46 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-225
Only for transmission with hydraulic control -E17-
Display
group
number Display
field Description
Test requirements
Spec. value
on V.A.G
1551
display Corrective actions
010
1 Torque increase in
torque converter While driving
1)
1...2,17
Calculated by the Transmission
Control Module (TCM) from the
torque converter slip speed

2 Engine speed
(RPM) With engine running approx.
0...8200
RPM - Perform electrical test page 01
-
273

- See DTC table, DTC 529 and 543
page 01
-45


3 Gear selected See display group number 1, display field 4

4 Anti-Slip Regulation
(ASR) While
driving
1)
activated
ASR active Only activated by the ASR control
module when necessary

not
activated -
1) While driving, a second mechanic is required to read specifications.
Pa
ge 47 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-226
Only for transmission with hydraulic control -E17-
Display
group
number Display
field Description
Test requirements
Spec. value
on V.A.G
1551
display Corrective actions
011
1 Selector lever
position See display group number 004, display field 2

2 Tiptronic Switch -
F189- Selector lever in tiptronic
gate M switch
- Perform electrical test from
page 01
-273


Selector lever not in
tiptronic gate -

3 Tiptronic Switch -
F189- Selector lever in tiptronic
gate, select gears
- Perform electrical test from
page 01
-273


Shift up
3)
Up switch

Shift down 2)
Down switch
4
Air conditioning
kick down While
driving
1)
activated
Comp. OFF A/C compressor switch-off is only
activated following kick-down for
down-shift

not
activated Comp. ON
Notes and footnotes for display group number 11 are on the next page.
Pa
ge 48 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-227
1) While driving, a second mechanic is required to read specifications. 2) Operate down-switch (-) by shifting selector lever toward rear. For vehicles equipped with a tiptronic sport steering wheel,
down switch must also be operated by pressing the lower left or right button (-) on the steering wheel in order to check it's
function. 3) Operate up-switch (+) by shifting selector lever toward front. For vehicles equipped with a tiptronic sport steering wheel, up-
switch must also be operated by pressing the upper left or right button (+) on the steering wheel in order to check it's function.
Pa
ge 49 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13