AUDI S3 2016 Repair Manual

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
Power seat adjustment
Applies to vehicles: with power adjustable seats
Fig. 48 Front se at: po wer se at adjust men t
@ -Adjusting the lumbar support: press the but­
ton in the applicable position .
@-moving the seat up/down : press the button
up/down. To adjust the front seat cushion, press
t he fron t button up/down. To adjust the rear seat
cushion, press the rear button up/down .
@-moving the seat forward/back: press the
but ton forward/back.
© -adjusting the backrest angle : press the but­
ton forward/back.
@ -lengthening/shortening the upper thigh sup­
port* : lift the grip handle.
A WARNING
- Only adjust the front seat with when the ve­
hicle is stationary. Otherwise, this increases
the risk of an accident
- The power adjustment for the front seats al­
so works with the ignition switched off or
with the ignition key removed. For this rea­
son, children should never be left unattend­
ed in the vehicle - they could be injured!
- Exercise caution when adjusting the seat
height. Unsupervised or careless seat ad­
justment can pinch fingers or hands causing
injuries .
- The front seat backrests must not be re­
clined too far back when driving, because
this impairs the effectiveness of the safety
belts and airbag system, which increases
the risk of injury.
Seats and storage
-To reduce the risk of injury during sudden
braking or in a collision, the driver and front
passenger should not have their backrests in
the reclined position while driving or riding .
The safety belts and airbag system can pro­
vide the greatest protection possible when
the backrests are in the upright position and
the safety belts are worn correctly. The
more a backrest is reclined, the greater the
risk of injury due to an incorrect seating po­
sition and safety belt position.
Front center armrest
Applies to vehicles: with front center a rm rest
The center armrest can be adjusted to several
l e ve ls.
Fig. 49 Armre st between th e driv er's /fro nt pa ssenger 's
s eats.
.,. To adjust the angle, raise the armrest~ fig. 49
notch by notch.
.,. To bring the armrest back down, raise it out of
the top notch and fold it back down. Then
lift
the armrest to the desired position, if necessa­
ry.
Please note that the driver 's ability to move his or
arm may be restricted when the armrest is folded
down. Because of this, the armrest should not be
folded down during city driving .
The armrest can slide forward and back.
There is a storage compartment under the arm­
rest .
59

Seats and storage
Rear center armrest
Applies to vehicles: with rear center armrest
The storage compartment and cup holder are in­
tegrated in the armrest.
Fig. SO Rear a rmrest
Folding the armrest down
• Tilt the armrest all the way down.
Opening the storage compartment
• Lift the cover on the upper rim.
~I
gl
~
For more information on the use of the cup hold­
ers , see ¢
page 62 .
Head restraints
Front head restraints
Applies to veh icles: with adjustable head restraints
-
'
' F ig. 51 Front seat: adjust ing the head restra int
Applies to vehicles w ith super sport seats* (not
pictured): the head restraint is integ rated in the
backrest and is therefore not adjustable
Adjust the head restra ints so the upper edge is as
even as possible with the top of your head. If that
is not possible, try to adjust as close to this posi­
tion as possible . Push the head restraint as close
as poss ible to the back of the head.
60
• To move the head restra int up or forward, slide
it unti l it locks into place.
• To move the head restra int down or back, press
the side button -arrow-¢
fig. 51 and slide the
head restraint until it locks into place.
Refer to ¢
page 170, Proper adjustment of head
restraints
for guidelines on how to adjust the
height of the front head restraints to suit the oc­
cupant's body size.
A WARNING
- Dr iving without head restra ints or head re­
stra ints that are not adjusted correctly dra­
matically increases the risk of serious or fa­
tal nec k injuries.
- Read and following the WARNINGS in
¢ page 170, Proper adjustment of head re­
straints.
@ Tips
Head restraints that are adjusted correctly
and safety belts are an extremely effective
combination of safety equipment.
Rear head restraints
ro -0
Fig. 52 Outer rea r head restra ints : re lease point
- 0 > :g
If there are passengers in the rear seat, fold the
head restraints up on the occ upied seats at least
to the next notch ¢
,& .
Adjusting the head restraints
• To move the head restra int up, hold it at the
sides with both hands and slide it upward until
you feel it click into place . .,.

.... N
0 > CX)
.... I.Cl U"I
.... I.Cl ....
.. To move the head restraint down, press the
button ®
¢fig . 52 and slide the head restraint
downward .
Removing the head restraints
To remove the head res tra ints, the back res t must
be folded forward partially .
.. Remove the screwdriver from the vehicle tool
kit
r:::;, page 280 .
.. Release the backrest r:::;, page 65 .
.. Press the button @ r:::;, fig . 52 and slide the head
restraint up as far as it can go
c::> ,& .
.. Place the screwdriver in position@ in the
opening, press the button ® and pull the head
restraint out of the backrest at the same time
r:::;, _& .
.. Fold the backrest down until it latches securely
r:::;, ,& in Increasing the size of the luggage
compartment on page 65 .
Installing the head restraints
To install the head restraints , the backrest must
be folded forward partially .
.. Release the backrest
c::> page 65.
.. Slide the posts on the head restraint down into
the gu ides until you feel the posts click into
place . You should not be able to pull the head
restra int out of the backrest .
.,. Fold the backrest down until it latches securely
r:::;, ,&. in Increasing the size of the luggage
compartment on page 65 .
A WARNING
- Only remove the rear seat head restraints
when necessary in order to install a child
seat . Install the head restraint again imme­
diately once the child seat is removed. Driv­
ing with the head restra ints removed or
head restraints not in the highest position
increases the risk of serious injury .
- Read and following the WARNINGS in
r:::;, poge 170 .
-
Seats and storag e
Cigarette lighter
Applies to vehicles: with cigarette lighter
Fig. 53 Center conso le : cigarette lighte r
.,. Press the c igarette lighter in .
.,. Remove the cigarette lighter when it pops out.
The cigarette lighter should only be used as a
power source when it is absol utely necessary.
A WARNING
The cigarette lighter only works when the ig­
ni tion is switched on. Inco rrect usage can lead
to serious inj uries or burns. To reduce the ris k
of injuries, never leave children unattended in
the vehicle with the vehicle key .
(D Note
- To red uce the risk of damage to the sockets,
only use plugs that fit correctly .
- T he ciga rette lighte r socket should only be
used as a powe r source fo r electr ical acces­
sories for a short pe riod of time. The sock­
ets* in the vehicle should be used for longe r
use of power supply .
(D Tips
The vehicle battery dra ins when accessories
are tu rned on but the engine is off.
.
61

Seats and storage
Socket
Applies to vehicles: with socket
Electrical accessories con be connected in the 12
volt socket.
-
--:,: -_-,--,-~
' ' I
Fig . 54 Center console: front/rear 12 volt socket•
Fig. 55 Luggage compartment s ide trim panel: 12 volt
socket * (example)
... Remove the plug from the center console sock­
et
¢ fig. 54, or
... Open the cover on the luggage compartment
socket*
¢ fig . 55 .
... Insert the plug for the electr ical device into the
socket.
The 12 volt socket can be used for electrical ac­ cessories. The power consumption at the outlet
m ust not exceed 120 watts.
A WARNING
The socket works only when the ignition is
switched on. Incorrect usage can lead to seri­
ous injur ies or burns. To reduce the risk of in­
jur ies, never leave children unattended in the
vehicle with the vehicle key.
(D Note
- To prevent damage to the socket, only use
the correct type of plugs.
62
- Never connect devices that generate electri­
cal power such as solar pane ls or a battery
charger to the 12 vo lt socket. They can dam­
age the vehicle e lectrica l system.
(D Tips
The vehicle battery drains when accessories
are turned on but the eng ine is off.
Storage
Beverage holders
Fig. 56 Center console: front cup holders
Fig. 57 Sect ion of the rear bench seat: rear cup holde rs*
Front cup holders
... Place beverages in the holder ¢fig. 56. There is
space for two beverages. A larger plast ic bottle
can be placed in the door trim.
Rear* cup holders
... To open the cup holders, tap on the rim@
¢fig . 57.
... To place the beverage container in the cup
holder, push the arm @ outward .
... Then push the arm against the beverage con­
tainer so that the arm lies closely against it .
... To close the cup holders, push them back into
t he slot . .,.

.... N
0 > CX)
.... I.Cl U"I
.... I.Cl ....
A WARNING
Spilled hot liquid can increase the risk of acci­
dents and injuries.
- Never drive with containers that contain hot
liquid such as coffee or tea. The hot liquid
could spill and cause burns during a colli­
sion, sudden braking or other vehicle move­
ment. Spilled hot liquid can also increase
the risk of accidents and injuries.
- Only use soft containers in the cup holders .
Hard cups and glasses can increase the risk
of injury during a collision.
- Never use the cup holder or the adapter as
an ashtray - this is a fire hazard.
(D Note
Beverage containers in the cup holders should
always have a lid . Otherwise, beverages could
spill and cause damage to vehicle equipment
or stain the seat covers.
Glove compartment
Fig. 58 Glove compartmen t
Opening/closing
.. To open the glove compartment, pull the han­
dle in the direction of the arrow.
.. To close the glove compartment , swing the lid
upward until it clicks into place .
The glove compartment can be locked using the
vehicle key .
A WARNING
Always leave the lid on the glove compart­
ment cover closed while driving to reduce the
risk of injury.
Seats and storage
Additional storage compartments
There are additional storage compartments,
compartments and holders at other locations in
the vehicle:
- In the upper part of the glove compartment.
- In the center console under the center arm -
rest* .
- On the back of the right front seat . The com­
partment* can hold a maximum weight of 2 lbs
(1 kg) .
- Garment hooks on the B -pillar
c:> ,& .
A WARNING ,~ -- Do not place any objects on the instrument
panel. Objects that are not stored securely
can slide around in the vehicle while driving ,
when accelerating or braking or when turn­
ing.
- Make sure that objects cannot fall out of the
center console storage compartment or oth­
er compartments and into the footwell
while driving. These objects could prevent
you from braking or accelerating during
sudden braking maneuvers.
- Garments hung on the hooks must not ob­
struct the driver's view . The garment hooks
are only designed for light objects. Do not hang any garments with hard, sharp or
heavy objects in the pockets on the garment
hooks . These objects could injure vehicle oc­
cupants during sudden braking or in a colli­
sion -especially if the airbags deploy .
-Always keep the glove compartment closed
while driving to reduce the risk of injury dur­
ing a collision or heavy braking .
- Read and following the WARNINGS in
¢ page 204, Important safety instructions
on the side airbag system.
- Hang garments so that they do not obstruct
the driver's view .
- The garment hooks should only be used for
light articles of clothing. Do not leave any
heavy or sharp-edged objects in the pockets
that could interfere with the side airbags
unfolding and cause injuries in the event of
a collision.
63

Sea ts and stor age
- Do not use coat hangers to hang garments,
because th is could reduce the effect iveness
of the side curtain airbags.
- Do not hang any heavy objects on the gar­
ment hooks, because they could cause injury
during heavy braking.
- Beca use of their load capac ity, the hooks
should only be used to secure objects that
weigh a maximum of 10 lbs (5 kg). Heavy
objects w ill not be secured suff ic iently, and
this increases the risk of injury.
Luggage compartment
Loading luggage compartment
Luggage items must be stowed securely.
F ig. 59 Place heavy objects as far forward as poss ible (ex­
amp le).
Note the following to preserve the vehicle's good
handling character istics .
• Distribute t he load as evenly as possible.
• Place heavy objects as far forward as possib le
¢ fig. 59.
• Secure luggage i tems with the cargo net* or
with non-elastic retai ning straps to the tie­
down rings *
¢page 66.
A WARNING
-
-Loose objects in the luggage compartment
can slide about suddenly and alter the vehi­
cle's handling characterist ics.
- Loose objects in the passenger compart­
ment can fly forward during abrupt maneu­
vers or acc idents and injure occupants.
64
- Always store objects in the luggage com­
partment and use su itab le straps, particu­
larly w ith heavy objects.
- When you transport heavy objects, always
remember that a change in the center of
gravity may result in a change in the vehi­
cle's handling characteristics.
- Follow all warnings¢
page 166, Driving
safety.
@ Tips
The tire pressure must be adjusted to the load
- see the tire pressure sticker located on the
driver's side 8-pillar.
General information
_&. WARNING
Refer to the chapter Dr iv ing Safely
¢
page 166, Driving safety for important in­
formation, tips, suggestions and warnings that you should read and follow for your own
safety and the safety of your passengers.
Luggage compartment cover
Applies to vehicles: With luggage co mpa rtment cover
(A3 Spo rtback)
The luggage compartment cover prevents the
view into the luggage compartment.
Fig . 60 Open luggage compartme nt lid wit h luggage com ­
pa rtment cove r
Removin g
• Unhinge the straps (D and pull the cover @in
the direction of the arrow out of the holder @. .,..

Installing
• Slide the cover@ hor izontally into the desig­
nated ho lder @in the side bracket until the
cover is lined up.
• Hook the straps into the l uggage compartment
lid @ ¢
A.
A WARNING
-To prevent accidents, never install the lug­
gage compartment cove r unsec ured.
- The luggage compartment cover is not a
surface for storing objects. Objects placed
on the cover increase the r isk of injury to all
vehicle occupa nts dur ing sudden bra king
mane uvers o r when i nvo lved in an accident .
Increasing the size of the luggage
compartment
-
The rear seat backre sts can be folded forward ei ­
ther separately or together.
F ig. 61 Backrest: re lease lever (le ft s ide, examp le)
Folding the backr est forward
• Push the corresponding head restraint down­
ward
¢ page 60.
• Press the release lever @ in the direct ion of the
arrow .
• Fold the backrest forward .
Folding the backrest back into the upright
position
• Fold the backrest down until it latches secure ly
¢ ,& .When you can no longer see the red mark
;::: on the pin @, the seat is la tched .
0 > CX)
rl I.Cl U"I
rl I.Cl rl
Seats and storag e
A WARNING
-~
-The backrest must be latched securely to
e nsu re that the safety belt is p rotecti ng the
center seating position .
- The bac krest must be securely latched so
objects cannot slide fo rward out of the lug­
gage compartment during sudde n braking .
- Always make su re the backrest is latched
completely by pull ing fo rwa rd on it .
- Make sure the safety belt is not caught in
the door hinges or the seat fittings and
damaged.
- To rn or frayed safety be lts can break, and
be lt anchors can b reak dur ing a col lision .
C heck the safety be lts regu la rly. Safety
be lts wi th noticeable damage to the we b­
b in g, b indings, bu ckles or ret ra cto rs m ust
be repla ced.
(D Note
- If you move the front seat back when the
rear seat backrest is fo lded fo rwa rd, yo u
c o ul d d am age the head restra in ts on t he
rear sea t. If necessary, remove the rear sea t
head restraint be fore mov ing the front seat
back
- Make sure the sa fe ty belt is not pinche d in
the back rest lock a nd damage d when the
rear seat backrest if folded back . Othe r ob­
jects should be removed from the rear
bench seat to protect the rear backrest from
damage .
65

Sea ts and stor age
Lowering the cargo floor
Applies to veh icles: w ith adj ustable cargo f loor
The cargo floor can lower to expand the storage
area in the luggage compartment.
F ig. 62 L uggage compartment: lowered cargo floor
The cargo floor can also be inse rted at a lower
point depending on vehicle eq uipment .
., Lift the cargo floor in order to lower it.
., Pull the cargo floor back slightly a nd insert it in
the lowe r pos it ion
@ .
To make loading and un load ing eas ier, br inging
the cargo floo r back into position @ afte r trans­
port ing b ulky i tems is recommended.
Tie-downs and cargo net
The cargo net* prevents small objects from slid­
ing.
F ig . 63 Luggage compartment: location of the tie -downs
66
F ig. 6 4 Luggage compartment: luggage compartment net•
spread out
., Secure the cargo to the tie-downs c::> fig. 63
-arrows- .
., To secure the cargo net, first hang the front
hooks in the tie-downs then hang the rear
hooks -arrows-
c::> fig. 64.
., Obse rve
the safety precaut ions c::> page 172,
Storing cargo correctly .
.&_ WARNING
Weak, damaged or fau lty straps used to se­
cure objects to the tie-downs can fail during
heavy braking or a co llision and lead to seri­
ous injur ies .
- Always use s uitable straps and secure ob­
jects to the tie-downs in the luggage com­
partment to prevent objects from shifting
and sliding forward.
- Never secure a child seat restraint to a tie­
down.
- Because of their load capacity, the hooks
should only be used to secure objects that
weigh a maximum of 10 lbs (5 kg). Heavy
objects will not be secured sufficiently, and
this increases the risk of inju ry.
-

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
Bag hooks
Applies to vehicles: with bag hooks
Fig. 65 A3 Sportba ck luggage com part men t: bag hook s
( r igh t sid e, e xampl e)
Fig. 66 A3 Sed an luggag e compartmen t: bag hoo ks (exa m­
p le )
You can also use the hooks to hang light purses ,
bags , etc.
_&. WARNING
The hooks can hold a maximum weight of 6
lbs. (3 kg). Heavier objects are not adequately
secured. There is risk of personal injury.
Seats and storage
Reversible mat
Applies to vehicles: with cargo mat
The reversible mat protects the luggage com­
partment and bumper from dirt and scratches.
Fig. 67 Lugg ag e compar tment: re ve rs ib le ma t w it h back­
rest folded forward (example)
You can use the reversible mat with the dirt-re­
sistant side or the decorative side. After loading
or unloading, fold up the reversible mat and
close the luggage compartment lid. Only store
the reversible mat if it is dry.
Pass-through
Appl ies to vehicles: with pass-through
Fig. 68 Backrest: pass -thro ugh cover
.,. Fold the rear seat center armrest down .
.,. Fold the pass-through cover down¢
fig. 68.
_&. WARNING
- Make sure that all objects that you are
transporting in the pass-through are secure.
They could slide around during sudden brak­ ing maneuvers and cause injuries .
- Sharp edges on objects that are loaded must be covered for protection.
67

Sea ts and stor age
Roof rack
Description and mounting locations
Additional cargo can be carried with a roof lug­
gage rack.
Fig. 69 Roof rack attachment points (w it h out roof rails)
Fig. 70 A3 Sportback w ith roof rail: Roof rack attac hment
points
" Always read and follow the instructions prov id­
ed by the roof rack manufacturer when instal­
ling the roof rack system .
If luggage or cargo is to be carried on the roof,
you must observe the followi ng:
- Only use roof racks approved for your vehicle.
These approved roof racks are the basis for a
complete roof rack system. Additional attach­
ments o r carrier systems are needed to trans­
po rt luggage and sports equ ipment. We recom­
mend using roof racks from the Aud i orig inal
accessor ies program.
- When ins tall ing the roof rack, make sure it is
o nly mounted on the designated locations on
the roof
r=;, fig. 69.
- We recommend that you keep the installation
inst ruct ions for your roof rac k system togethe r
with yo ur Ow ner's li teratu re in the vehicle.
68
When should th e roof rack be removed?
- Before goi ng through an automatic car wash (it
is best to ask the car wash operator for advice).
- When not in use, to reduce fuel consumpt ion,
w ind no ise and to g uard aga inst theft.
_& WARNING
- Use of an unapproved roof rack or incorrect
mounting of an approved roof rack can
cause the roof rack or the items attached to
it to fall off the roof onto the road.
- Objects falling from the roof of a vehicle can
cause a crash and personal injury.
- On ly mount the roof rack on the designated
locations on the roof
r=;, fig. 69.
- The roof rack system must be insta lled ex­
actly according to the i nstr uctions provided.
- When drivi ng with a roof rack system,
changes to the center of gravity and wind
resistance can change the vehicle handling
and lead to a co llision. Always adapt yo ur
driving and your speed to the current condi­
tions.
(D Note
- Your vehicle warranty does not cove r any
damages to the vehicle caused by using roof
racks or mounting structures not approved
by Audi for yo ur vehicle . The same applies to
damage resulting from incorrect roof rack
ins tallation.
- Always check the roof rack mountings and hardwa re before each trip and du ring a t rip
to ma ke sure eve ry t hing is securely tight­
ened. If necessa ry, retighte n the mountings
and che ck the entire sys tem from time to
t ime.
- After mou nting a roof rac k system, o r when
yo u transport ob jects on the roof o f your
ve­
hicle, the he ight of the vehicle is natura lly
increased. Be careful when driving under
low bridges or in parking garages for exam­
ple. This could cause damage to the load
and
even the vehicle itself.
- Make sure the open rear lid and the sun­
roof" do not come into contact w it h the roof
rack.